SAFETY INSTRUCTIONS
Failure to observe the following instructions may result in serious damage to property and personal injury!
Danger!
Do not operate the work light if it shows visible
damage.
Danger! - Burns of the skin and fires
Parts of the work light can get hot. Allow the work light
to cool before touching and observe the installation
and operating conditions.
Danger! - Glare and damage to the eyes
Luminaires can have very high luminances. Never
look from a short distance or permanently in the light
of a luminaire.
Danger! - Electric shock, fires and property
damage
Work on the circuits and the electrical installation
of the work light must be carried out by a qualified
electrician. Disconnect the work light from the power
supply before carrying out such work.
Do not make any changes to the work light, supply
line and plug connections.
Inside the work light are parts that are under elec-
trical voltage. Never remove covers. There are no
user-serviceable parts inside the device. Before
using the work light, check that the information on
the work light matches that of the power supply.
Use this work light only in the areas for which it is
approved.
Note! - Operating conditions
The work light is suitable for indoor use. Observe the
specified operating conditions.
Avoid heavy dirt and strong vibrations.
Note! - Protection against overvoltage
LED work lights must be protected against overvolt-
ages by suitable means.
Note! - Checking of the protective devices
Check the work light and protective equipment
regularly in accordance with the applicable legal
requirements.
Note! - Warranty Terms
The guarantee of the product warranty is only given
in compliance with the guarantee conditions.
Power 30 W
Input voltage 230 V AC
Rated frequency 50/60 Hz (CPS)
Number of LEDs 32
Luminous flux 3480 Im
Light output 116 lm/W
Beam angle 60°
Color temperature 5000 K
Color rendering index Ra > 70
Ambient temperature
(operation / storage)
−30 °C to +50 °C
−22 °F to +122 °F
Humidity
(operation / storage) 10 % to 90 %
Dimmable No
Clamping range Up to 3G1.5
Protection class I
Degree of protection IP65
Shock resistance level IK08
Housing material Die-cast aluminium
Lamp glass Impact-resistant glass
Mass 1.65 kg / 3.64 lbs
PRODUCT FEATURES / TECHNICAL DATA
INSTALLATION AND COMMISSIONING
Unpack the work light and carefully inspect it for damage
before use.
Keep the packaging. In order to optimally protect the work
light against vibrations, dust and moisture during transport
and storage, use the original packaging or your own suitable
transport or storage packaging.
Only make the electrical connection in a de-energized condi-
tion and in compliance with legal regulations.
Use only suitable connecting cables. The work light is
switched on or off by plugging in or unplugging the power
plug.
EU conformity. Meets the European safety standards
Recognized Component Mark. Underwriter Laborato-
ries tested for US safety standards.
IP65 Dustproof
Hose-proof
IK08 Impact strength according to IEC 62262
D
D-fire rating according to standard EN 60598-2-24
Danger high voltage
Warning of a dangerous spot
Note
SHORT SIGNS AND SYMBOLS
Fig. 1 Release the cross handles. Fig. 2 Place the work light on the cross
handles and push it upwards.
Fig. 3 Move the work light to the left.
Fig. 4 Tighten the cross handles. Fig. 5 Insert the plug with the screw [A]
turned up (1) and lock with the
bracket (2).
Fig. 6 Insert the motor cable into the
extension cable.
Fig. 7 Insert the mains plug into the
socket. The work light lights up.
Fig. 8 Disconnect the power plug from the
socket. The work light goes off.
Fig. 9 The work light can be swiveled up
and down.
OPERATING INSTRUCTIONS / SAFETY INSTRUCTIONS English OPERATING INSTRUCTIONS / SAFETY INSTRUCTIONS
English
DIMENSIONS
135,5 mm
5.33 in
130 mm
5.12 in
191 mm / 7.52 in
160 mm / 6.3 in
40°
110°
