Laguna Tools Smartshop SUV User manual

1
Smartshop SUV Manual 2021
Basic Operations-Main Screen Set-up, Set-up Menus, Machine Settings,
CNC Tool Data, Delivery Protocols, Warranties, Packaging/RMA
Procedures.
744 Refuge Way
Grand Prairie, TX. 75050
Direct Phone #: [phone]
Warranty Repair Information: [phone]
Laguna Tools

2
•Main Screen Buttons & Flow.
•CNC Positions.
•Machine Settings.
•Edit/Check “G” Code.
•CNC Tools Data.
•Axis Calibration.
•Program Manager.
•CNC Settings.
•Axis Settings.
•“Jog” Positions.
•“Settings” from Main Screen.
•Program Preview from Main Screen.
•Alarm Screens.
•Schematics.
•Delivery Protocol.
•Parts & Service.
•Warranty.
•Packaging/RMA Procedures/Bill of Lading.
Table of Contents-

3
Main Screen Button(s) & Flow-
“Main” Screen

4
Main / Home Screen Defined-
Above is the Start-Up Home Screen-
Park Tool = Pressing this button will put the active tool in spindle into its tool holder and leave the spindle
empty.
Preventive Maintenance Note-
*****One should never leave a tool in spindle when machine is Idle. Leaving a tool in spindle will
cause rust and damage to tool holder and or spindle.
Verify Origin = Pressing this button will move the machine to whatever ZPO (Z-Point Origin) Coordinates
is selected on the Jog screen, G54-G59.
****ZPO (Z-Point Origin) coordinates –These are based on the G54-G59 set and selected from the Jog Screen.

5
Main / Home Screen Defined-
Hold = The Hold button is used to Pause a program run. Press the Run button to continue.
NOTE: The spindle stays running during hold. Press stop button to stop the spindle and program.
Run = The Run button is used to start a CNC Program.
Preview Program = This button will open a visual representation of the active program in X and Y axis
and provide a estimated run time.
Settings = The settings button enters the Override / MDI screen. This is also accessible from the set-up
menu screen under CNC Settings.
Hold
Preview Program
Run
Settings

6
Main / Home Screen Defined (Cont’d.)-
Right Side Fields defined:
Select Program drop down window = This field
allows you to quickly select a program from the
files copied to the controller’s memory.
Active Tool = This references the current tool in
spindle.
Feed rate = This shows the current federate as
dictated by the active program.
Spindle RPM = This shows the current spindle speed.
Start at Block = This is the run from line number
function. With the machine in a Stopped state input
the line in which you would like to start from and
press the Run button.
Start at Tool = This field allows the program to jump
to a specific tool for it’s starting point. Input the tool
number desired then press run. There will be a slight
delay while the code is scanned to the requested
starting point.

7
Main / Home Screen Defined (Cont’d.)-
Coord’s Selector/Lower Right Drop
Down = This is the selector for the X,Y,
and Z coordinates displayed at the
bottom of the Main Page.
FROM DRP DOWN MENU-
1. ZPO Coordinates –These are based
on the G54-G59 set and selected from
the Jog screen.
2. Machine Coordinates –These are the
actual distances from machine “Zero”.
3. Relative Coordinates –These are
resettable to zero from current
position and equate to a digital tape
measure function.
CNC Monitor = These 5 lines are
displaying the CNC “G”-Code as
it is running.
DROP DOWN MENU

8
Main Screen Buttons & Flow to proceed to CNC Positions-
“Set-Up” Screen Appears-
1. Make sure one is in “Machine Coordinates”.
2. From the “Main Screen” select the “SET UP” Button, then it will proceed to
“Set-Up” Screen.

9
CNC Positions-
2a. Select “CNC Positions” Button.
4a.Press “Main” Button to return to amin/Home Screen.

10
CNC Positions (Cont’d.)-
6. Then press the “Settings” Button.