Lakeland CFU139 User manual

CFU139
CEDAR LOG GLIDER
Please check contents before assembly If any items are missing or damaged, do not take the unit back
to the store Call 1-800-427-5136 for customer service and e ill save you time by correcting any
problems directly for you.
NOTE:
• Read all instructions before starting.
• Do not completely tighten any scre s until the
unit is fully assembled and setting on a level
surface.
• Use a rubber mallet (or a block of ood bet een
the hammer and the unit) to drive do eled ends
into holes as far as possible.
CEAR LOG GLIDER COMPONENTS LOG GLIDER HARDWARE
(Sho n smaller than actual size)
NOTE: Cracks or Checks in logs are part of the natural
beauty of cedar logs and should not be considered defects.
TOOLS REQUIRED
Lay assembled seat on floor. Insert do el
end of uprights on assembled back into holes
on the back seat rail, adjust uprights in or
out as needed to align properly. Do not tap on
seat back ith hammer.
To keep the seat rail from splitting, lay the
back on the floor and drive the seat onto the
do elled ends by hitting on the bottom of the
seat assembly.
STEP 1
2 Glider End Assemblies
Rail 57” Long
Preassembled Back
6 Braces
9” Long
2 Back Legs
26” Long
2 Arms
20” Long
Preassembled Seat
1 Left
Front Leg
26” Long
1 Right
Front Leg
26” Long
STEP 2
Make a right leg set and a left leg set by
inserting do el end of back leg into angled hole
of front leg. The drilled holes on each leg should
face the same direction as sho n in figure 2.
Put arms onto legs by inserting do el end of front
legs into the hole in the arms. Drive arm onto leg
assembly as far as possible.
figure 1
figure 2

Lay back and seat assembly on its side and
insert do el ends of seat rail into holes on leg sets.
Drive legs on as far as possible. Turn assembly over
and repeat procedure for the other side.
Scre a brace onto the seat rail and to the leg.
Repeat process on other side. As illustrated in figure
3.
Set chair in upright position on a level surface and
hen legs are in proper position, bring ARM in
against UPRIGHT. Tighten the preinstalled lag
scre s into the pilot hole in the arm ith a rench
or socket. Secure do eled joints in place ith
scre s perpendicular to the do eled ends as
sho n in figure 6. Repeat procedure for other
side.
Factory: 1 Lakeland Place, P.O. Box 350, Edmore, Michigan 48829, Phone: [phone] Fax: [phone],
.lakelandmlls.com
Check all joints for tightness before and during each usage season.
If you have hardware left over after completing your unit, it most
likely has been assembled incorrectly, and may not be safe to use.
Please call Customer Service at 800 427 5136 for assistance.
STEP 3
STEP 4
STEP 5
STEP 6
Insert glider rail into glider ends. Rail should
be off centered to the back of the glider base.
Scre on braces as sho n using 2” flat head
scre s, by placing them on the top and front
of each end of the glider rail. Note the
location of asher and glider strap on lag
scre . Attach all four glider straps to glider
base ith the 1/4” x 2-1/2” lag scre into pre
drilled holes.
Turn Glider Base on it’s side. Secure
do el joint in place ith flat head scre
perpendicular to do eled end as sho n
in figure 5. Repeat on other end of
glider base.
figure 3
figure 4
figure 5
figure 6
figure 7
STEP 7
Set assembled seat into glider base and attach
bottom of glider strap to legs of unit ith lag
scre s, in pilot holes. As sho n in figure 7.
Tighten do n all lag scre s firmly to secure
unit. Your glider is no assembled and
ready for finish or immediate use. Relax
and enjoy!
STEP 8
STEP 9