Lancom AirLancer ON-Q360ag User manual

LANCOM Antenna
AirLancer ON-Q360ag

MOUNTING INSTRUCTIONS
Attaching the antenna bracket by wall mounting
In the case of wall mounting, attach the antenna bracket to
the wall with the enclosed bolts. You may need to drill the
holes first and insert dowels.
Attaching the antenna bracket by pole mounting
In the case of pole mounting, use screw clamps to attach
the antenna bracket directly to the pole.
Attaching the antenna arm to the antenna
When attaching the antenna arm to the antenna, please
ensure that there is a close fit between them. Make use
of the pin on the antenna arm and the matching recess in
the antenna. Finally, use the locking screw to secure the
antenna arm to the antenna.
Important
Mounting the antenna upside down
If the antenna will be mounted outdoors and with the
cables exiting upwards, it is essential to have a good seal by
sticking the insulation disk to the antenna before attaching
it to the antenna arm.

MOUNTING INSTRUCTIONS
Attaching the antenna to the antenna bracket
The antenna is attached to the antenna bracket by means
of the antenna arm. To do this, place the antenna-arm joint
socket onto the joint head of the antenna bracket. Tighten
this joint with the wing screw or hexagon socket screw
supplied. Whichever screw you use, please be sure to use
the washer supplied.
Attaching the antenna to a suspended ceiling
This requires a 3-cm diameter hole in the suspended ceiling.
First stick the insulation disk to the antenna. This acts as a
washer and protects the ceiling and the antenna. Insert the
cables and the screw thread through the hole in the ceiling.
Then screw the locking screw onto the screw thread and
tighten it.
Important
Working responsibly with high frequencies
The AirLancer ON-Q360ag meets the requirements of
the R&TT directives 1995/5/EC and the FCC & ARPANSA
regulations. To ensure compliance with these requirements,
a minimum distance of 20 cm must be maintained between
the antenna and the human body when operating the
antenna.
Important
Electrical and electronic equipment law
In the interests of recycling, please do not dispose of
electrical and electronic waste in your household garbage.
Ensure that your electrical and electronic waste is disposed
of in accordance with the regulations in your country.

MOUNTING INSTRUCTIONS
Important
Proper handling of antenna cables
Antenna cables are sensitive RF cables. During installation it is important that the cables are not
creased, and bent as little as possible, otherwise the antenna will suffer a loss of performance. Do
not coil the antenna cable in tight loops.
Important
Antenna gain and terminating unused antenna connectors on the access point
It is essential for unused antenna connectors on the access point to be terminated with the supplied
rod antenna. The terminating resistor supplied with the adapter AirLancer AN-RPSMA-NJ is suitable
for use with indoor access points. In addition, you must disable the unused antenna connectors in
LCOS (changing the antenna grouping of the respective WLAN module), and configure the antenna
gain of the antenna. The settings can be found in LANconfig at:
Configuration > Wireless LAN > General > Physical WLAN settings > Radio
Operating mode
2x2 MIMO & 2x2 MIMO
Apart from its standard operation as a 4x4 MIMO antenna, this antenna can also be used by two
WLAN modules operating in two different frequency ranges. This is done by connecting two of the
connectors to each WLAN module. As the AirLancer ON-Q360ag has antenna segments that are
aligned equally to one another, you are free to choose your arrangement.

LANCOM, LANCOM Systems and LCOS are registered trademarks. All other names or descriptions used may be trademarks or registered trademarks of their owners. Subject to change without notice. No liability for technical errors and/or omissions.
Technical details
Frequency range 2400 - 2500 MHz, 4900 - 5900 MHz
Antenna characteristics
Radiation characteristics
horizontal (2.4 GHz) 360°
vertical (2.4 GHz) 60°
horizontal (5 GHz) 360°
vertical (5 GHz) 33°
Recommended use Hotspot, coverage of open spaces
VSWR 2.0:1 max.
Gain 2.4 GHz 4 dbi max.
5 GHz 4 dbi max.
Mechanical details
Size 26 x 16 cm (height x diameter)
Weight 950 g
Temperature range -30°C to 70°C
Color light grey
Material UV-resistant plastic
Mounting options Wall, pole, and ceiling mounting
Cables, connectors 4 x 91.4 cm UV-resistant RG58 cable with N-plug connector
Item
Warranty 2 years for AirLancer and accessories
Item number 61246
Package content
Antenna, insulation disk, antenna arm, antenna bracket, locking screw, fastening
bolts (2x wall mounting, hexagon socket screw/wing screw with washer to
connect antenna arm to antenna bracket), Quick Reference Guide
2400 MHz
2500 MHz
5150 MHz
5400 MHz
5900 MHz
-40
-35
-30
-25
-20
-15
-10
-5
0
5
0
30
60
90
120
150
180
210
240
270
300
330
2410 MHz
2470 MHz
5000 MHz
5300 MHz
5800 MHz
-25
-20
-15
-10
-5
0
5
0
30
60
90
120
150
180
210
240
270
300
330
2410 MHz
2470 MHz
5000 MHz
5300 MHz
5800 MHz
2.4 & 5 GHz h-plane 2.4 & 5 GHz e-plane