L&L ARC336700D1 User manual

ARC336700D1
+DARC336700D1
rev. 00 18/07/2018
L&L Luce&Light / Via della Tecnica, 46 / 36031 Povolaro di Dueville, Vicenza / Italy / T [phone] / F [phone]
E [email protected] / www.lucelight.it 1/2
Made in Italy
44
44
25
ARC336700D1
WARNING!!!
Please read the following instructions carefully.
IMPORTANT:
• Although LED runs on a very low voltage, always cut o󰀨 the power supply before installing the LED light or subjecting it to
maintenance.
• Unauthorised alterations or tampering of the product will invalidate all the conditions of guarantee.
• This xture must be istalled by a qualicate electrician.
• Install the device in a well-ventilated place.
• The device generates heat when in function.
• L&L Luce&Light is not resposable if its xtures are not installed in according to local safety standards.
• Data contained in this document may be changed at any moment without prior notice and do not place L&L Luce&Light under
any implicit or explicit obligation.
The 3-channel sequence, used to dynamically change colour in RGB lamps.
INSTALLATION INSTRUCTIONS
Power supply units and control gear
44
44
25
Rated voltage
12 — 48 Vdc
Output current
700 mA

12 ÷ 48 Vdc
PP
Out 700 mA
RGB
V
in
ARC336700D1
RED +
ROSSO +
ROUGE +
ROT +
ROJO +
VERMELHO +
RED +
ROSSO +
ROUGE +
ROT +
ROJO +
VERMELHO +
RED +
ROSSO +
ROUGE +
ROT +
ROJO +
VERMELHO +
GREEN +
VERDE +
VERT +
GRÜN +
VERDE +
VERDE +
BROWN -
MARRONE -
MARRON -
BRAUN -
MARRÓN -
CASTANHO -
BROWN -
MARRONE -
MARRON -
BRAUN -
MARRÓN -
CASTANHO -
BLUE +
BLU +
BLEU +
BLAU +
AZUL +
AZUL +
BLUE +
BLU +
BLEU +
BLAU +
AZUL +
AZUL +
BLUE +
BLU +
BLEU +
BLAU +
AZUL +
AZUL +
WHITE -
BIANCO -
BLANC -
WEIß -
BLANCO -
BRANCO -
WHITE -
BIANCO -
BLANC -
WEIß -
BLANCO -
BRANCO -
GREY -
GRIGIO -
GRIS -
GRAU -
GRIS -
CINZENTO -
GREY -
GRIGIO -
GRIS -
GRAU -
GRIS -
CINZENTO -
GREEN +
VERDE +
VERT +
GRÜN +
VERDE +
VERDE +
GREEN +
VERDE +
VERT +
GRÜN +
VERDE +
VERDE +
ARC336700D1
L&L Luce&Light / Via della Tecnica, 46 / 36031 Povolaro di Dueville, Vicenza / Italy / T [phone] / F [phone]
E [email protected] / www.lucelight.it 2/2
INSTALLATION INSTRUCTIONS
CONNECT THE SPOTLIGHTS AND THE PUSH BUTTONS BEFORE POWERING THE CONTROL DEVICE
USING WITH N.O. PUSH BUTTON
PUSH SHORT PRESS: switches the spotlights on/o󰀨.
PUSH LONG PRESS (>3 SEC): locks the sequence on the colour present at that time.
PUSH LONG PRESS (>3 SEC): restarts the sequence.
CYCLE TIME SELECTION (WITH DEVICE SWITCHED OFF)
PUSH LONG PRESS (WHEN SWITCHED OFF): choice of 4 levels of ashing LEDs, which stand for the cycle times:
• fast ashing: 6 sec cycle
• fast ashing 1: 30 sec cycle
• fast ashing 2: 6 min cycle
• slow ashing: 30 min cycle
NO PUSH BUTTON
USE N.O. PUSH BUTTON
MAXIMUM DISTANCE 10 m
USE SHIELDED CABLE
Max 6 Spot RGB
3x2W
(Vin = 24 Vdc)
Max 12 Spot RGB
3x2W
(Vin = 48 Vdc)
CONNECT IN SERIES