Landmann 0423 User manual

IMPORTANT - Please read the instructions carefully before assembling
A ssembly Instructions
43CM ROUND CHARCOAL KETTLE BBQ
Assembly Instructions
PLEASE RETAIN THE INSTRUCTIONS FOR FUTURE USE.

How to use your barbecue
• For outdoor use only.
• Allow a miniumum of 1m clearance between this product and any surface which may
be affected by heat.
• Always use on a flat, firm and level surface.
• Combustible or flammible materials should never be stored within 1m of this product
when in use.
the barbecue
barbecue
barbecue
item.
barbecue
the barbecue
barbecue
barbecue
2
Safety and Care Advice
Burning charcoal inside can cause harm which
mainly results in serious injury
Wait for it to become cool.
.
winds.
Only use

3
PARTS LIST
Please check parts against the list below before assembling your Barbecue Grill. Take a few moments
to familiarise yourself with the contents. Check that all holes are clear of paint before assembly.
1 PC
2 PCS
1 PC
1 PC
1 PC
1 PC
1 PC
2 PCS
2 PCS
4 PCS
1 PC
2 PCS
1 PC
(A) ROUND BAKELITE HANDLE
(B) SQUARE BAKELITE HANDLE
(C) HANGING HOOK
(D) FIRE BOWL
(E) LID
(F) COOKING GRILL
(G) CHARCOAL GRILL
(H) SHORT LEG
(I) LONG LEG
(J) LEG CUP
(K) ASH TRAY
(L) WHEEL
(M) WIRE SHELF

4
H
A
N
D
Y
H
I
N
T
S
please read all instructions carefully and keep packaging for future reference, you can
always compare the assembled barbecue with the image on packaging.
WARNING
Dispose of all polythene packing carefully and keep out of the reach of children.
Please read the section on barbecue safety prior to using your Barbecue.
(N) AIR VENT (FOR LID)
(O) ASH VENT
(P) M 4 X 20 BOLT
(Q) M6 X 30 BOLT
(R) M 4 X 10 BOLT
(S) PLASTIC WASHER
(T) WHEEL NUT
(U) M4 NUT
(V) Ø4 WASHER
(W) Ø6 WASHER
(X) M4 NUT
(Y) M6 X 16 BOLT NUT
1 PC
1 PC
2 PCS
4 PCS
2 PCS
2 PCS
2 PCS
2 PCS
2 PCS
8 PCS
2 PCS
4 PCS
(FOR FIRE BOWL)

ASSEMBLY
H
A
N
D
Y
H
I
N
T
S
All sharp edges have been carefully removed during manufacturing process, but please
be careful when handling all components to avoid accident to happen.
Tools required: Either a Philips crosshead or flat bladed screwdriver
and either an adjustable spanner or a pair of pliers.
WARNING
STEP 1 - LID ASSEMBLY & HANGING HOOK
Place round bakelite handle (A) with bolt (P) on lid (E) and
align round bakelite handle with hanging hook (C) which
you place inside of the lid. Then secure with washer (V)
and nut (X).
STEP 2 - ATTACHING HANDLES
Take one of the square handles (B) and remove the two
bolts (Y) and washers (W) that are attached to it. Fix the
handle to the outside of the fire bowl (D), using two of the
holes near the rim. Then fix the second square handle to
the opposite side of the fire bowl.
STEP 3 - FITTING LEGS
Next, take one of the short legs (H) and remove the bolt
(Q) and washer (W) from its top. Place a leg cup (J) over
the top of the leg. Note, that the hole in the cup must go
onto the leg first, so the cup points upwards. Push the bolt
and washer through any one of the four holes in the
bottom of the fire bowl. Next, screw into the top of the
leg, making sure the leg cup sits squarely against the
bottom of the fire bowl. At this point, do not fully tighten
the bolt, but leave some movement in the leg. Now, attach
the other three legs in the same way.
Note: The second short leg must sit next to
the first short leg. This means one of
the handles you fixed to the bowl will
be between the two short legs. This
also applies to the long legs.
(A)
(E) (C)
(V)
(X)
(P)
(W)
(B)
(Y)
(W)
(D)
(Q)
(W)
(J)
(H)
5

6
STEP 4 - ATTACHING WIRE SHELF
Place the fire bowl upside down on the floor so that the
four legs point upwards and make sure that the short
legs are closest to you.Take the wire shelf (M) and
position it so the threaded bar is closest to your body
and the two kinks at the other end of the shelf point
upwards. Insert the kinked ends of the shelf into the
holes nearest the end of the long legs. You may need to
tilt the shelf upwards slightly to fit them in. It may be
necessary to turn the legs round to line the holes up.
Once you have done this,insert the threaded ends of
the shelf into their corresponding holes in the short
legs (closest to you). You will have to push the legs outward
slightly to do this.
STEP 5 - WHEEL ASSEMBLY
Place the wheels (L) on the threaded ends of the
wire shelf (M) and fix with wheel nuts (T) and washer (S)
tighten wheel assembly.
Note: you may have to squeeze the legs
inwards to fit the nuts on the threaded ends
STEP 6 - ASSEMBLY AIR VENT
Using bolt (R) and wing nut (U) to fit air vent (N) to the
outside of the lid.
(M)
(L)
(T) (S) (M)
(U)
(N)
(R)
Important: Now stand the barbecue on its
legs and fully tighten the four
screws holding the legs.

7
STEP 7 - ASSEMBLY OF AIR VENT
The air vent with handle (O) should be attached to the
underside of the fire bowl.Use bolt (R) and wing nut (U)
to secure in place.
(G)
(F)
(K)
(O)
(R)
(U)
STEP 8 - PLACING OF CHARCOAL GRILL,
COOKING GRILL & ASH TRAY
Place the charcoal grill (G) inside the fire bowl, seating
it on the ledge that runs round the fire bowl, party away
down. Place the cooking grill (F) inside the fire bowl
also, ensuring its two handles are facing upwards.
Finally, fix the ash tray (K) to the four legs. Place the
ash tray on the wire shelf between the four legs and lift
towards the fire bowl, making sure the legs line up with
Now push the ash tray back down the leg a little and it
will be firmly locked against the legs
The barbecue grill is now fully assembled and you are
ready to enjoy your first barbecue.
the four gaps around the ash tray. Slide the ash tray up
as far as it will go and then turn it slightly clockwise.

barbecue
r r
barbecue
r
r r
Q
barbecue
barbecue
8

9
r
barbecue
barbecue
barbecue
r r
barbecue
r r.
barbecue
barbecue
barbecue
barbecue
rbarbecue
barbecue
barbecue
barbecue
barbecue
barbecue
cooking grill(F)
charcoal grill(G)