Lanner FW-7551 User manual

>>
Network
Application Platforms
Hardware platforms for next generation networking infrastructure
FW-7551
V1.3
User's Manual
Date (Y/M/D): 2017/05/09

i
About
About
Network Application Platforms
Overview
Icon Descriptions
The icons are used in the manual to serve as an indication
of interest topics or important messages. Below is a
description of these icons:
NOTE: This check mark indicates that
there is a note of interest and is something
that you should pay special attention to
while using the product.
WARNING: This exclamation point
indicates that there is a caution or
warning and it is something that could
damage your property or product.
Online Resources
The listed websites are links to the on-line product
information and technical support.
Resource Website
Lanner http://www.lannerinc.com
Product
Resources
http://www.lannerinc.com/download-
center/
RMA http://eRMA.lannerinc.com
Copyright and Trademarks
This document is copyrighted, © 2014. All rights are
reserved. The original manufacturer reserves the right to
make improvements to the products described in this
manual at any time without notice.
No part of this manual may be reproduced, copied,
translated or transmitted in any form or by any means
without the prior written permission of the original
manufacturer. Information provided in this manual is
intended to be accurate and reliable. However, the original
manufacturer assumes no responsibility for its use, nor for
any infringements upon the rights of third parties that
may result from such use.
Acknowledgement
Intel, Pentium and Celeron are registered trademarks of
Intel Corp.
Microsoft Windows and MS-DOS are registered trademarks
of Microsoft Corp.
All other product names or trademarks are properties of
their respective owners.
Compliances
CE
This product has passed the CE test for environmental
specifications. Test conditions for passing included the
equipment being operated within an industrial enclosure.
In order to protect the product from being damaged by
ESD (Electrostatic Discharge) and EMI leakage, we strongly
recommend the use of CE-compliant industrial enclosure
products.
FCC Class B
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when
the equipment is operated in in a residential environment.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may cause
harmful interference to radio communications. Operation
of this equipment in a commercial area is likely to cause
harmful interference in which case the user will be required
to correct the interference at his own expense.
Safety Guidelines
Follow these guidelines to ensure general safety:
• Keep the chassis area clear and dust-free during and after
installation.
• Do not wear loose clothing or jewelry that could get caught
in the chassis. Fasten your tie or scarf and roll up your
sleeves.
• Wear safety glasses if you are working under any conditions
that might be hazardous to your eyes.
• Do not perform any action that creates a potential hazard
to people or makes the equipment unsafe.
• Disconnect all power by turning off the power and
unplugging the power cord before installing or removing a
chassis or working near power supplies
• Do not work alone if potentially hazardous conditions exist.
• Never assume that power is disconnected from a circuit;
always check the circuit.

ii
About
About
Network Application Platforms
LITHIUM BATTERY CAUTION:
Risk of Explosion if Battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions
Operating Safety
Electrical equipment generates heat. Ambient air temperature
may not be adequate to cool equipment to acceptable
operating temperatures without adequate circulation. Be sure
that the room in which you choose to operate your system has
adequate air circulation.
Ensure that the chassis cover is secure. The chassis design
allows cooling air to circulate effectively. An open chassis
permits air leaks, which may interrupt and redirect the flow of
cooling air from internal components.
Electrostatic discharge (ESD) can damage equipment and
impair electrical circuitry. ESD damage occurs when electronic
components are improperly handled and can result in complete
or intermittent failures. Be sure to follow ESD-prevention
procedures when removing and replacing components to avoid
these problems.
Wear an ESD-preventive wrist strap, ensuring that it makes
good skin contact. If no wrist strap is available, ground yourself
by touching the metal part of the chassis.
Periodically check the resistance value of the antistatic strap,
which should be between 1 and 10 megohms (Mohms).
EMC Notice
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when
the equipment is operated in a residential environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may cause
harmful interference to radio communications. Operation
of this equipment in a commercial area is likely to cause
harmful interference in which case users will be required
to correct the interference at their own expense.
Consignes de sécurité
Suivez ces consignes pour assurer la sécurité générale :
• Laissez la zone du châssis propre et sans poussière
pendant et après l’installation.
• Ne portez pas de vêtements amples ou de bijoux qui
pourraient être pris dans le châssis. Attachez votre
cravate ou écharpe et remontez vos manches.
• Portez des lunettes de sécurité pour protéger vos
yeux.
• N’effectuez aucuneaction qui pourraitcréerundanger
pour d’autres ou rendre l’équipement dangereux.
•
• Coupez complètement l’alimentation en éteignant
l’alimentation et en débranchant le cordon
d’alimentation avant d’installer ou de retirer un
châssis ou de travailler à proximité de sources
d’alimentation.
• Ne travaillez pas seul si des conditions dangereuses
sont présentes.
• Ne considérez jamais que l’alimentation est coupée
d’un circuit, vérifiez toujours le circuit. Cet appareil
génère, utilise et émet une énergie radiofréquence
et, s’il n’est pas installé et utilisé conformément aux
instructions des fournisseurs de composants sans
fil, il risque de provoquer des interférences dans les
communications radio.
Avertissement concernant la pile au
lithium
• Risque d’explosion si la pile est remplacée par une
autre d’un mauvais type.
• Jetez les piles usagées conformément aux
instructions.
• L’installation doit être effectuée par un électricien
formé ou une personne formée à l’électricité
connaissant toutes les spécifications d’installation et
d’appareil du produit.
• Ne transportez pas l’unité en la tenant par le câble
d’alimentation lorsque vous déplacez l’appareil.
• La machine ne peut être utilisée qu’à un lieu fixe
comme en laboratoire, salle d’ordinateurs ou salle de
classe.

iii
About
About
Network Application Platforms
Sécurité de fonctionnement
• L’équipement électrique génère de la chaleur. La
température ambiante peut ne pas être adéquate
pour refroidir l’équipement à une température de
fonctionnement acceptable sans circulation adaptée.
Vérifiez que votre site propose une circulation d’air
adéquate.
• Vérifiez que le couvercle du châssis est bien fixé. La
conceptionduchâssispermetàl’airderefroidissement
de bien circuler. Un châssis ouvert laisse l’air
s’échapper, ce qui peut interrompre et rediriger le flux
d’air frais destiné aux composants internes.
• Les décharges électrostatiques (ESD) peuvent
endommager l’équipement et gêner les circuits
électriques. Des dégâts d’ESD surviennent lorsque
des composants électroniques sont mal manipulés et
peuvent causer des pannes totales ou intermittentes.
Suivez les procédures de prévention d’ESD lors du
retrait et du remplacement de composants.
- Portez un bracelet anti-ESD et veillez à ce qu’il soit
bien au contact de la peau. Si aucun bracelet n’est
disponible, reliez votre corps à la terre en touchant la
partie métallique du châssis.
Vérifiez régulièrement la valeur de résistance du
bracelet antistatique, qui doit être comprise entre 1 et
10 mégohms (Mohms).
Consignes de sécurité électrique
• Avant d’allumer l’appareil, reliez le câble de mise à la
terre de l’équipement à la terre.
• Une bonne mise à la terre (connexion à la terre) est
très importante pour protéger l’équipement contre
les effets néfastes du bruit externe et réduire les
risques d’électrocution en cas de foudre.
• Pour désinstaller l’équipement, débranchez le câble
de mise à la terre après avoir éteint l’appareil.
• Un câble de mise à la terre est requis et la zone reliant
les sections du conducteur doit faire plus de 4 mm2
ou 10 AWG.
Procédure de mise à la terre pour source
d’alimentation CC Procédure de mise à la
terre pour source d’alimentation CC
• Desserrez la vis du terminal de mise à la terre.
• Branchez le câble de mise à la terre à la terre.
• L’appareil de protection pour la source d’alimentation
CC doit fournir 30 A de courant.
Cet appareil de protection doit être branché à la source
d’alimentation avant l’alimentation CC.
Version Date
(M/D/Y)
Descriptions
0.2 08/13/2013 Take o CMOS Jumper
1.0 03/24/2014 Ocial release
1.1 06/24/2014 Modied CPU specications,
ordering information and block
diagrams
1.2 08/19/2015 Modied memory specications
1.3 05/09/2017 Modied expansion specica-
tion

TTaTTable of Contentsbeable of Contents
iv
Chapter 1: Introduction 1
System Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Front Panel Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Rear Panel Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Chapter 2: Hardware Setup 5
Preparing the Hardware Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installing the System Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installing the Hard Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installing the CompactFlash Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Chapter 3: Motherboard Information 7
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Motherboard Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Chapter 4: BIOS Settings 13
Accessing the BIOS menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Navigating the BIOS menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
The Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Advanced Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Intel RCSetup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Security Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Boot Conguration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Save & Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Save and Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Appendix A: Programming Watchdog Timer 28
Appendix B: Setting up Console Redirections 29
Appendix C: Programming Generation 2 LAN Bypass 30
Lanner Generation 2 Bypass. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Appendix D: Installing Intel QuickAssist Software for Linux 31
Appendix E: Terms and Conditions 32
Warranty Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
RMA Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

1
Introduction
Network Application Platforms
Chapter 1
Chapter 1:
Introduction
Thank you for choosing the FW-7551. This system
integrates the newest Intel® Atom Processor C2000
series processor, codenamed Rangeley, with the Intel
QuickAssist technology to provide a robust and high-
performance communication platform. It supports up to
8GB of DDR3 system memory at 1333 or 1600 MHz.
The C2000 series processor comes with an enhanced
cryptographic/content processing acceleration via
integrated Intel®QuickAssist Integrated Accelerator:
–Bulk Encryption: AES, DES, 3DES, RC4
–Hash: SHA-1, MD5; SHA-2 (SHA-224, SHA-256, SHA-
384, SHA-512);
Authentication: HMAC, AES-XCBC, AES-CCM, and
AES-GCM
–Public Key Exchanges: RSA, DH, DSA, ECC
The processor also supports Intel Virtualization
Technology.
The FW-7551 is equipped with advanced I/O capabilities
,which incorporates a console port, one Serial-ATA port
and two USB 2.0 ports as well as a ComplactFlash slot.
The system also features 6 GbE ports. In addition, the 4
(of all 6) LAN ports are equipped with Lanner proprietary
Generation 2 bypass.
Please refer to the chart below for a summary of the
system’s specifications.
Note: For instructions on quick installation and
acquiring the Intel® Atom™ Processor C2000
Product Family for Communications Infrastructure
Software for Linux* Software package, refer to the
attached PDF file.
Form Factor Desktop
Platform Processor Options
Intel® Atom™ SoC CPU
C2358(2-core) / C2518
(4-core) / C2758(8-core)
BIOS AMI BIOS
System
Memory
Technology
DDR3 1333/1600 MHz, ECC
only
Max. Capacity 8 GB (for SKU A and B)
16GB (for SKU C and D)
Socket
1 x 204-pin SO-DIMM (for
SKU A and B)
2 x 204-pin SO-DIMM (for
SKU C and D)
OS Support Linux Kernel 2.6 or above
Storage HDD Bays 1 x 2.5” HDD/SSD kit
CompactFlash 1 x Type II CompactFlash
Networking
Ethernet Ports 6 x GbE RJ45 onboard
Bypass SKU A/C/D: 2 pairs Gen.2,
SKU B: N/A
Controllers 2 x Intel i210AT,
4 x Marvell 88E1543
Ethernet Modules N/A
Management Port N/A
I/O Interface
Reset Button 1 x reset button
Software reset by default
Console 1 x RJ45
USB 2 x USB 2.0
IPMI via OPMA
slot N/A
Display N/A
Expansion PCIe 1 x Mini-PCIe Half Size
(PCIe/USB2.0)(By SKU)
PCI N/A
Cooling Processor CPU heatsink
System 1x cooling Fan
Environmental
Parameters
Temperature,
ambient operating
/ storage
0 ~ 40º C / -20~70º C
Humidity (RH),
ambient operating
/ ambient non-
operating
5~90%, non-condensing /
5~95%, non-condensing
Miscellaneous
LCD Module N/A
Watchdog Yes
Internal RTC with
Li Battery Yes
Physical
Dimensions
Dimensions
(WxHxD) 240 x 44 x 166 mm
Weight 1.2 kg
System Specifications

2
Introduction
Network Application Platforms
Chapter 1
Package Contents
Your package contains the following items:
• FW-7551 Network Security Platform
• Power cable
• 1 console cable
• Drivers and user’s manual CD.
Optional Accessories
The system has a variety of optional accessories, visit the
following website for more information.
http://www.lannerinc.com/products/x86-network-
appliances/rackmount/fw-7551
Power Type/Watts 36W Power Adapter
Input 100~240V@50~60Hz
Approvals and Compliance CE, FCC Class B, RoHS
Ordering Information
FW-7551A
Intel® Atom™ processor C2358 (Code-
named “Rangeley”), 1x DDR3 SO-DIMM
socket, 6 GbE LAN ports with Gen.2 Bypass,
36 W power adapter
FW-7551B
Intel® Atom™ processor C2358 (Code-
named “Rangeley”), 1x DDR3 SO-DIMM
socket, 4 GbE LAN ports without Bypass, 36
W power adapter
FW-7551C
Intel® Atom™ processor C2518 (Code-
named “Rangeley”), 2 x DDR3 SO-DIMM
socket, 6 GbE LAN ports with Gen.2 Bypass,
60 W power adapter
FW-7551D
Intel® Atom™ processor C2758 (Code-
named “Rangeley”), 2 x DDR3 SO-DIMM
socket, 6 GbE LAN ports with Gen.2 Bypass,
60 W power adapter

3
Introduction
Network Application Platforms
Chapter 1
Front Panel Features
F1 Power/Status/HDD LED
Power: If the LED is on it indicates that the system is powered on. If it is off, it indicates that the system is powered off.
Status: This LED is programmable. You could program it to display the operating status with the following behavior:
If the LED is green, it indicates that the system’s operational state is normal. If it is red, it indicates that the system is
malfunctioning.
HDD: If the LED blinks, it indicates data access activities; otherwise, it remains off.
F2 These LEDs are indicators for the 6 Ethernet ports on the back panel.
Speed LED: If the LED is amber, it indicates that the connection speed is 1000Mbps. If the LED is green, it indicates that the
connection speed is 100Mbps. And if it is off, it indicates that the speed is 10Mbps.
Link/ACT LED: If the LED is on, it indicates that the port is active. If it blinks, it indicates that there is traffic.
F1 F2

4
Introduction
Network Application Platforms
Chapter 1
Rear Panel Features
R2
R1 R5
R1 Reset Switch
The reset switch can be used to reboot the system without turning off the power.
R2 Power-in Socket
The system requires an ATX 60W Power Supply.
R3 Power-on Button
R4 Console Port
By using suitable rollover cable or RJ-45 to DB-9 console cable, you can connect to a computer terminal for diagnostic
or configuration purpose. Terminal Configuration Parameters: 115200 baud, 8 data bits, no parity, 1 stop bit , no flow
control.
R5 Two USB 2.0 Ports
It connects to any USB devices, for example, a flash drive.
R6 Ethernet Ports (LAN3-LAN4: bypass pair; LAN5-LAN6: bypass pair *)
4(of all 6)on-boardEthernet ports equip with 2pairs of LAN bypass. These4GbE ports areprovided byMarvell 88E1543and
the other two are provided by Intel i210AT. LAN1 is capable of Preboot eXecution Environment (PXE) (This feature needs
to be enabled or disable in the BIOS; the default is disabled). Two pairs (LAN3-LAN4, LAN5-LAN6) can be configured as
LAN Bypass by using Lanner Gen2 Bypass technology when failure events occur. This feature can be enabled dynamically
with a watch dog timer. Refer to your User’s Manual CD for a sample implementation of this feature.
Note:
1. The LAN bypass functionality is only available on model FW-7551A.
2. The FW-7551B only has 4 Ethernet ports
RESET
DC + 12v
R3
POWER
R4
CONSOLE
USB
R6
1 2 3 4 5 6
LAN1 LAN2
Intel i210AT Intel i210AT
LAN3 LAN4
Marvell 88E1543 Marvell 88E1543 (bypass pair)
LAN5 LAN6
Marvell 88E1543 Marvell 88E1543 (bypass pair)

5
Hardware Setup
Chapter 2
Network Application Platforms
Chapter 2:
Hardware Setup
Preparing the Hardware Installation
To access some components and perform certain service
procedures, you must perform the following procedures
first.
WARNING: To reduce the risk of personal injury,
electric shock, or damage to the equipment,
remove the power cord to remove power from the
server. The front panel Power On/Standby button
does not completely shut off system power.
Portions of the power supply and some internal
circuitry remain active until AC power is removed.
1. Unpower the FW-7551 and remove the power cord.
2. Unscrew 2 screws on each side and the bottom of the
top cover of the FW-7551 System.
3. Slide the cover backwards to open it.
Installing the System Memory
The motherboard supports DDR3 memory that features
data transfer rates of 1333, 1600 MHz to meet the higher
bandwidth requirements of the latest operating system
and Internet applications. To install the memory:
1. Open the DIMM slot latches.
2. Install the DIMM.
Note:
1. The system requires DDR3 1333/1600 MHz (ECC)
memory.Do not install memories with different
specifications.
2. The system can support up to 8 GB in maximum.
Installing the Hard Disk
The system can accommodate one 2.5” Serial-ATA disk.
Follow these steps to install a hard disk into the FW-7551:
1. Unscrew the 4 screws on the hard disk tray to take out
the hard disk tray from the system.
2. Place hard disk on the hard disk tray and align the holes
of the hard disk with the mounting holes on the tray.
3. Secure the hard disk with 4 mounting screws on the
bottom of the hard disk tray.
4. Connect the Serial-ATA power and data disk cables
to the hard disk’s power and drive connector
respectively.
5. Plug the Serial-ATA power and data disk cables to the
Serial-ATA power and drive connectors on the main
board.
6. Put the hard disk tray with the installed hard disk back
to the system and secure it with the mounting screws.

6
Hardware Setup
Chapter 2
Network Application Platforms
.
Note:
1. The HDD kit is not included in the package; order
it separately.
2.5” HDD installation
Installing the CompactFlash Card
FW-7551 provides one CompactFlash slot. Follow the
procedures bellow for installing a CompactFlash card.
1. Align CompactFlash card and the card slot with the
arrow pointing toward the connector. The card fits
only the correct way into the slot; do not force the card
into the slot.
2. Push the card to insert into the connector.

7
Motherboard Information
Network Application Platforms
Chapter 3
Chapter 3:
Motherboard Information
Block Diagram
The block diagram depicts the relationships among the
interfaces or modules on the motherboard. Please refer
to the following figure for your motherboard’s layout
design.
Intel® Atom™ processor
C2358 (Codenamed Rangeley)
LPC
6x GbE RJ-45 / Connectors w/ LED
2x PCI-E x1
Dual Channel
DDR3 1333/1600 MHz
ECC DIMM only
Up to 8GB Maximum
2x SATA
connectors
1x 2.5"
CF
2x USB
PIN header
2x USB
connectors
USB 2.0
SATA
3.0
Golden Finger
SuperIO
SPI
RJ45 console
Reset
Bottom
MB-7551
SATA
2.0
4x GbE MAC
By-pass By-pass
Intel
I210
Intel
I210
Marvell 88E1543
SFP223A
GPIO
Fan Monitor
Thermal Monitor
Watchdog
Mini-PCIe
Socket
PCIe x1 (optional)
(Codenamed Rangeley)
1x or 2x DDR3/L 1333 / 1600 MHz
204-pin SO-DIMM

8
Motherboard Information
Network Application Platforms
Chapter 3
Motherboard Layout
The motherboard layout shows the connectors and
jumpers on the board. Refer to the following picture
as a reference of the pin assignments and the internal
connectors.
PS1
GPIO1
DIMM1
CF1
SATA6G_1
PKMB1
COM1
USB1
LAN
LAN
LAN
LAN
LAN
LAN
FAN1
LPC1
USB2
SATA6G_2
J21

9
Motherboard Information
Network Application Platforms
Chapter 3
Jumper Settings
Fan Connectors(FAN1 ): The 3-pin connector is for
connecting the CPU fan.
ATX Power Connector (PS1): This 8-pin connector are
for connecting ATX power supply plugs.
Pin No. 1 2 3
Signal GND +12V FAN Status
USB Connector(USB2): It is for connecting the USB
module cable. It complies with USB2.0 and support
up to 480 Mbps connection speed.
Dual USB 2.0 Ports (USB1): This provides two USB 2.0
ports in the front panel.
Console Port (COM1)
Pin No. Signal
1 P5V_ATX
2 GND
3 GND
4 P12V
5 P3V3_ATX
6 GND
7 P5VSB_ATX
8 PSON
Pin No. Signal
1 +P5V_USB0_L
2 USB0_SB_L_DN
3 USB0_SB_L_DP
4 GND
5 +P5V_USB0_L
6 USB1_SB_L_DN
7 USB1_SB_L_DP
8 GND
1 2 3 4
5 6 7 8
Pin No. Signal Pin No. Signal
1 LNRTSA# 5 GND
2 LNDTRA# 6 LNSINA
3 LNSOUTA 7 LNDSRA#
4 GND 8 LNCTSA#
Pin No. Signal Pin No. Signal
1 +P5V_USB2_L 2 NC
3 USB2_SB_L_DN 4 NC
5 USB2_SB_L_DP 6 NC
7 GND 8 GND
9 GND 10 Key ping
1
2
3
81
2
1
10
9

10
Motherboard Information
Network Application Platforms
Chapter 3
GPIO Output Pin (J10): Theses pins can be used to write
to an internal register to control the GPIO output pin
state.
SPI-ROM Update Connector (SPI-ROM1): It is for
updating the SPI Flash soldered on board for service
and repair purposes.
LPC I/O bus (It can also be called Port 80) (LPC1): It is
a proprietary connector for connecting a checkpoint
device to output checkpoints throughout booting
and Power-On Self Test (POST) to indicate the task
the system is currently executing.
CompactFlash Connector (CF1): It is for connecting a
Compact Flash card to be served as your system’s
storage. The connector is a CF Type II slot which could
fit both CF Type I or CF Type II cards.
25 1
50 26
CF1
1
Pin No. Function Pin No. Function
1 GND 26 DET1
2 CF_DD3 27 CF_DD11
3 CF_DD 4 28 CF_DD 12
4 CF_DD 5 29 CF_DD 13
5 CF_DD 6 30 CF_DD 14
6 CF_DD 7 31 CF_DD 15
7 -CF_DCS0 32 -CF_DCS1
8 GND 33 CF_VS1
9 GND 34 CF_DIOR_N
10 GND 35 CF_DIOW_N
11 GND 36 WE#
12 GND 37 CF_IDEIRQ
13 VCC_CF 38 VCC_CF
14 GND 39 MST_SLV
15 GND 40 CF_VS2
16 GND 41 CF_IDERST_N
17 GND 42 CF_IORDY
18 CF_DA2 43 CF_DMARQ
19 CF_DA 1 44 CF_DDACK_N
20 CF_DA 0 45 CFACT_N
21 CF_DD0 46 CF_PDIAG
22 CF_DD 1 47 CF_DD 8
23 CF_DD 2 48 CF_DD 9
24 GND 49 CF_DD 10
25 DET2 50 GND
9
10
1
2
Pin No. Function Pin No. Function
1 SIO_GP20 2 SIO_GP21
3 SIO_GP46 4 SIO_GP47
5 SIO_GP53 6 SIO_GP54
7 SIO_GP56 8 SIO_GP57
9 P5V 10 GND
Pin No. Function Pin No. Function
1 SPI_HOLD0_L 2 NC
3 PMU_AVN_SPI_R_CS0 4 V_3P3_SPI
5 PMU_AVN_SPI_MISO 6 NC
7 NC 8 PMU_AVN_SPI_R_CLK
9 GND 10 PMU_AVN_SPI_R_MOSI
Pin No. Function Pin No. Function
1 CLK_33M_P80 2 LPC_AD1
3 PLTRST_PORT80_N 4 LPC_AD0
5 LPC_FRAME_N 6 P3V3
7 LPC_AD3 8 Key ping
9 LPC_AD2 10 GND
9
10
1
2
2
1
10
9

11
Motherboard Information
Network Application Platforms
Chapter 3
4-Pin SATA Power Connector (PS4P1)
AT-Mode Power Button Connector (J21) It is for
connecting the power switch in AT mode.
Hardware or Software Reset Jumper(J4): The jumper
can be adjusted to be in either hardware or software
reset mode when the reset switch is pressed. The
hardware reset will reboot the system without turning
off the power. The software reset can be programmed
to reset a software to its default setting.
Keyboard and Mouse Connector (PKMB1)
DIMM Socket (DIMM1): The 204-pin DDR3 SO-DIMM is
for connecting the DDR3 1333/1600 ECC memory.
The system can support up to 8 GB in maximum.
SATA Connector (SATA6G_1, SATA6G_2): It is for
connecting a SATA harddisk to be served as your
system’s storage. The system can accommodate one
disk (2.5) with SATA 3.0 standard. The controller
contains two modes of operation—a legacy mode
using I/O space, and an AHCI mode using memory
space. Software that uses legacy mode will not have
AHCI capabilities.
The AHCI (Advanced Host Controller Interface) is a
programming interface which defines transactions
between the SATA controller and software and
enables advanced performance and usability with
SATA. Platforms supporting AHCI may take advantage
of performance features such as no master/slave
designation for SATA devices—each device is treated
as a master—and hardware assisted native command
queuing. AHCI also provides usability enhancements
such as Hot-Plug.
Note:
1. You will need to configure your SATA as
AHCI mode in the BIOS in order to use the
advanced features of SATA. To do this, access
the BIOS menu under IntelRCSetup->
South Bridge Chipset Configuration->SATA
Configuration.
2. Also, the hotplug enable/disable option is
under the same SATA Configuration menu.
Enable the hotplug function explicitly in this
menu if you need it.
Pin No. Signal
1+12V
2 GND
3 Ground
4 5V
Pin No. Signal
1 P3VSB
2 MR
Pin No. Signal
1 GND
2 TX_P
3 TX_N
4 GND
5 RX_N
6 RX_P
7 GND
1
2
3
4
5
6
7
1
2
3
4
1 2
Pin No. Signal
1-2 Hardware reset
2-3 Software reset
3 2 1
7
8
1
2
Pin No. Signal Pin No. Signal
1 +P5V_KM 2 MS_L_CLK
3 MS_L_DAT 4 NC
5 KB_L_DAT 6 NC
7 GND 8 KB_L_CLK

12
Motherboard Information
Network Application Platforms
Chapter 3
PCIe Expansion Connector (MPCIEC1): Mini-PCIe
connector
PIN NO. FUNCTION PIN NO. FUNCTION
1 PMU_WAKE# 27 GND
2 VCC3 28 1.5V
3 NC_RSV1 29 GND
4 GND 30 SMB_CLK
5 NC_RSV2 31 MINI_PCIE_TXN0
6 1.5V 32 SMB_DATA
7 MINI_CLKREQ_N1 33 MINI_PCIE_TXP0
8 NC_UIM_PWR 34 GND
9 GND 35 GND
10 NC_UIM_DATA 36 USB_IO3_DN
11 MINIPCIE_REFCLKN 37 GND
12 NC_UIM_CLK 38 USB_IO3_DP
13 MINIPCIE_REFCLKP 39 VCC3
14 NC_UIM_RST 40 GND
15 GND 41 VCC3
16 NC_UIM_VPP 42 NC_LED_WWAN#
17 NC_RSV3 43 GND
18 GND 44 NC_LED_WLAN#
19 NC_RSV4 45 NC_RSV9
20 RF_KILL_N2_R 46 NC_LED_WPAN#
21 GND 47 NC_RSV10
22 PLTRST_MINIPCIE_N 48 1.5V
23 MINI_PCIE_RXN0 49 NC_RSV11
24 P3VSB 50 GND
25 MINI_PCIE_RXP0 51 NC_RSV12
26 GND 52 VCC3

13
Bios Settings
Chapter 4
Network Application Platforms
Chapter 4:
BIOS Settings
Accessing the BIOS menu
When you are installing a motherboard or when the
system prompts “Run Setup” during start-up, you will use
the BIOS Setup program to configure the system, . This
section explains how to configure your system using this
program.
Even if you are not prompted to enter the BIOS Setup
program when you are installing a motherboard, you can
still change the configuration of your computer later on
with this program. For example, you may want to enable
the security password feature or change the power
management settings. This requires you to reconfigure
your system by using the BIOS Setup program so that the
computer can recognize these changes and record them
in the CMOS RAM .
When you start up the computer, the system provides you
with the opportunity to run this program. Press <Delete>
during the Power-On-Self-Test (POST) to enter the Setup
utility (There are a few cases that other keys may be
used, such as <F1>, <F2>, and so forth.); otherwise, POST
continues with its test routines.
If you wish to enter Setup after POST, restart the system
by pressing <Ctrl+Alt+Delete>, or by pressing the reset
button on the system chassis. You can also restart by
turning the system off and then back on. Do this last
option only if the first two failed.
The Setup program is designed to make it as easy to use as
possible. Being a menu-driven program, it lets you scroll
through the various sub-menus and make your selections
from the available options using the navigation keys.
Note: This manual describes the standard look of
the setup screen. There may be some instances in which
the motherboard features can vary from one to another
due to customization.This means that some of the options
described in this manual mays not match that of your
motherboard’s AMIBIOS.
Navigating the BIOS menu
The BIOS setup utility uses a key-based navigation system
called hot keys. Most of the BIOS setup utility hot keys can
be used at any time during the setup navigation process.
These keys include <F1>, <F10>, <Enter>, <ESC>, <Arrow>
keys, and so on.
Keys Description
-><- Left/Right The Left and Right <Arrow> keys
allow you to select an setup screen.
For example: Main screen, Advanced
screen, Boot screen, and so on.
Up/Down The Up and Down <Arrow> keys
allow you to select an setup item or
sub-screen.
+- Plus/Minuss The Plus and Minus <Arrow> keys
allow you to change the field value
of a particular setup item. For
example: Date and Time.
Tab The <Tab> key allows you to select
setup fields.
->
->

14
Bios Settings
Chapter 4
Network Application Platforms
The Main Menu
The main BIOS setup menu is the first screen that you can
navigate. Each main BIOS setup menu option is described
in this chapter.
TheMain BIOSsetup menu screenhas twomainframes.The
left frame displays all the options that can be configured.
“Grayed-out” options are configured parameters and
cannot be modified. On the other hand, Options in blue
can be modified.
The right frame displays the key legend. Above the key
legend is an area reserved for a text message. When an
option is selected in the left frame, it is highlighted in
white. Often a text message will accompany it.
System Language
Use this item to choose the BIOS language.
System Time/System Date
Use this option to change the system time and date.
Highlight System Time or System Date using the <Arrow>
keys. Enter new values through the keyboard. Press the
<Tab> key or the <Arrow> keys to move between fields.
The date must be entered in MM/DD/YY format. The time
is entered in HH:MM:SS format.

15
Bios Settings
Chapter 4
Network Application Platforms
Advanced Settings
Select the Advanced tab from the setup screen to enter
the Advanced BIOS Setup screen. You can select any of
the items in the left frame of the screen, such as SuperIO
Configuration, to go to the sub menu for that item. You
can display an Advanced BIOS
Setup option by highlighting it using the <Arrow> keys.
All Advanced BIOS Setup options are described in this
section. The Advanced BIOS Setup screen is shown at
the right. The sub menus are described on the following
pages.
PXE Function
The Preboot eXecution Environment (PXE) allows you to
boot computers using a network interface independently
of data storage devices (like hard disks) or installed
operating systems. Enable or disable this function with
this option here. For LAN port that can be configured to
PXE function, refer to Chapter 1 Introduction.