Lanoptik HW Series User manual

4K Smart Microscope Camera
User’s Manual
www.lanoptik.com
HW Series

Content
www.lanoptik.com
CHAPTER 1 NOTES AND SAFETY REQUIREMENTS
1.1 CAUTIONS AND NOTES
CHAPTER 2 SOFTWARE SYSTEM REQUIREMENTS
CHAPTER 3 PACKING LIST
CHAPTER 4 FUNCTION INTRODUCTION OF EACH PART
4.1 NAME AND FUNCTION FOR EACH PART OF THE CAMERA
CHAPTER 5 PRODUCT ASSEMBLY GUIDE
5.1 SMART EMBEDDED CAMERA ASSEMBLY
5.1.1 Assembly with trinocular microscope
5.1.2 Disassembly the Camera
CHAPTER 6 INSTRUCTIONS
6.1 SOFTWARE INSTALLATION
6.3 METHOD OF PARFOCALIZING
6.4 START TO USE
CHAPTER 7 DISCLAIMER
- 1 -
- 1 -
- 2 -
2.1 SYSTEM REQUIREMENTS FOR CONNECTION TO PC WORK MODE - 2 -
- 3 -
- 4 -
- 4 -
- 5 -
- 5 -
- 5 -
- 5 -
- 6 -
- 6 -
6.2 DEVICE CONNECTION - 6 -
- 7 -
- 7 -
- 8 -
2.1 SYSTEM REQUIREMENTS UNDER HDMI WORKING MODE - 2 -
6.2.1 WiFi working mode - 6 -
6.2.2 HDMI working mode - 6 -

To avoid danger or damage incurred to the lens, do not touch the lens or sensor directly with your
fingers.
Chapter 1 Notes and Safety Requirements
1.1 Cautions and Notes
User's Manual | Microscope Camera HW Series
To avoid failure or electric shock hazard and so on, do not disassemble or modify the internal
structure of the device.
Do not plug in or unplug the Power connection port when hands are wet.
Do not use alcohol and other organic solvents to clean.
If the lens or sensor is dirty or damp, you should better use dry and non-linen fabric or professional
lens tissue to wipe them. To avoid scratches on the surface, do not touch the lens with your fingers.
Wipe the lens or sensor lightly.
The products are not specifically designed for an outdoor use. Do not expose it to outdoor
environment without any protection. Excessive temperature and humidity will damage the lens.
Please avoid using the product under the following environment: high temperature or high humidity
environment, places with direct sunlight, dirt or vibration and places near heat source.
Please use and store in the following environment:
Operating temperature ： 0℃~ 40℃
Storage temperature ： -20℃~ 60℃
Operating Humidity ： 30~60%RH
Storage Humidity ： 10~80%RH
If any foreign matter, water or liquid enter into the device by accident, disconnect the Power line
immediately. Please send it to the maintenance center and do not use the hair dryer to dry it by
yourself.
To prevent microscope from being tripped over or dropped, please put away the device’s connect
cable in use or standby.
To avoid electric shock by accident, please power off microscope before you move your computer or
laptop.
The cleanliness of the device lens will directly affect clarity degree of contents from the computer
screen during preview. Problems like various circles or spots on the screen may mostly be incurred
by dirt on the lens. When cleaning, please use professional lens tissue or other professional detergent
to clear the dirt on the lens.
Registered trademark and copyright: Copyright ownership of this produc belongs to Lanoptik
Technologies Ltd. Without written authorization of this company, any organizations or individuals
shall not photocopy, print, or translation to another language to any part of this document.
www.lanoptik.com
- 1 -

Windows 7 (64bit), Windows 8 (64bit), Windows 8.1 (64bit), Windows 10 (64bit) , Windows 11 (64bit)
2.1 System Requirements for connection to PC Work Mode
Chapter 2 Software System Requirements
User's Manual | Microscope Camera HW Series
Dual core 3.0GHz or higher CPU
8G or more memory
At least 10 GB available hard-disk space
1000Mbps/100Mbps compatible with network cable interface
2.2 System Requirements for HDMI Work Mode
The monitor has an HDMI TYPE A interface.
The display supports up to 3840x2160 P60 output
Display HDMI interface support hot plug
www.lanoptik.com
- 2 -
2.3 System Requirements under WiFi Work Mode
5.0 or above version for Android system.
8.0 or above version for IOS system.
Wireless network hardware must support the 802.11ac protocol (5G WiFi mode).

User's Manual | Microscope Camera HW Series
www.lanoptik.com
- 3 -
Mouse & Keyboard Suite
Embedded Smart Camera
12V AC Adapter
2.Hexagon Key
Chapter 3 Packing List
HDMI Cable

4.1 Name and Function for Each Part of the Camera
Chapter 4 Function Introduction of Each Part
User's Manual | Microscope Camera HW Series
www.lanoptik.com
- 4 -
Power in: Connect with the AC adapter in the accessories to supply power to the camera.
Reset hole: Long press for 8 seconds to reset the camera.
USB 3.0 interface: Can connect a mouse, keyboard or USB flash disk, convenient use of embedded
APP.
USB 2.0 interface: Can connect a mouse, keyboard or USB flash disk, convenient use of embedded
APP.
HDMI interface: Through the HDMI cable, connect with the display device with HDMI interface, realize
video, signal transmission.
WiFi antenna: Enhance 5G WiFi signal transmission.
Power on-off button: Power on/off ： 1) after being electrified, press for 3 seconds to start the
camera; 2) after the camera is started, long press for 3 seconds to prompt the "shutdown/restart"
option; 3) after starting the camera, press the button for 5 seconds to shut it down.
Headset interface: Connect with headset cable to realize the mutual transmission of audio signals.
Signal indicator light: 1) When the camera is started: there is signal transmission, the indicator light
flashes; When no mobile device is connected indicator light is always on; 2) When the camera is off:
the indicator light is not on.
C mount: Connect to a microscope with C-mount adapter.
Signal indicator light: 1) When the camera is started: there is signal transmission, the indicator light
flashes; When no mobile device is connected indicator light is always on; 2) When the camera is off:
the indicator light is not on.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.

Chapter 5 Product Assembly Guide
5.1 Camera Assembly
5.1.1 Assembly with trinocular microscope
1. Screw out the dust cover of C-mount of the trinocular KoPa scope, as shown in figure 1
2.Smart Camera assembly
1)Take out the dust cover of the smart camera
2)Screw the smart camera onto the C thread of KoPa scope
3. Please refer to "Chapter 6" for camera connection and use.
5.1.2 Disassembly the Camera
1 ． Reverse the assembly sequence
User's Manual | Microscope Camera HW Series
www.lanoptik.com
- 5 -
Figure 1 Figure 2

Chapter 6 Instructions
User's Manual | Microscope Camera HW Series
6.1 Application installation for smart devices
www.lanoptik.com
- 6 -
6.2 Device Connection
6.2.1. WiFi Connection
Method 1: Automatic connection to mobile devices via scan QR code
1) Mount the camera to the microscope: refer to "Chapter 5",
2) Power the camera
3) Run "KoPa WiFi Lab"APP,
4) Click the "scan" icon in the App and scan the WiFi QR code on the top of camera to preview image,
5) Please refer to [ User Manual of KoPa WiFi Lab ] for detailed operation.
Scan “APP QR code”to install APP
Use the smart terminal device to scan the QR code of the student camera and download and install [KoPa
WiFi Lab] as prompted.
Select APP download entry according to
the systemtypeofthesmartterminal
After the APP download is complete, follow the prompts to allow installation and allow all authorizations.
Clicking "Not Allowed" will result in an inability to connect properly.
For Android users, if you can log in to the Google App Store, you can click one of the two buttons
to download.
For Android users in mainland China, please click the button to download.
iOS system users please click the button to download

User's Manual | Microscope Camera HW Series
www.lanoptik.com
- 7 -
Method 2: Manually connect to mobile devices by entering a password
1) mounting the camera to a microscope: refer to "Chapter 5"
2) power the camera
3) search for the following WiFi signal in the Settings of the mobile device and enter the password
WiFi name: WiFiCamera_5G_xxxxxx;
Default Password: 12345678
4) Run "KoPa WiFi Lab" APP and click the preview icon of the APP to display image.
5) Please refer to [ User Manual of KoPa WiFi Lab ] for detailed operation.
6.2.2 HDMI Connection
1. mounting the camera to a microscope: refer to "Chapter 5"
2. connect the camera with the display device with HDMI cable, and turn on the HDMI display device.
3. power the camera
4. Plug a mouse to the USB port.
5. Long press the power switch on the camera for 3 seconds to activate the camera
6. The camera is started normally. Please refer to the [User Manual of KoPa WiFi Lab AO] for detailed
operation.
6.3 Method of Parfocalizing
1. Place the specimen on the loading platform of the microscope, adjust the eyepiece diopter to the
minimum value, and use the 10X objective lens. It is recommended to use any black spot/or the darkest
point on the focusing section under visual observation to be the clearest.
2. Use the allen key to turn the focusing screw and adjust the focal length until the image from
software is clear.
6.4 Start to Use
The camera is ready for use now

Please do not use wet hands to plug and unplug the power supply of the equipment.
Please be sure to use a regular brand power socket, and make sure the grounding is well grounded to
prevent electric shock.
Please be sure to make regular safety checks on sockets and plugs to avoid potential electrical
safety hazards caused by aging and short circuit.
Please be sure not to use the product in a humid or hot environment to ensure the safety of the
product.
Please be sure to loosen bundle cords of the power cable before using, to avoid electromagnetic
induction and heating, thus increasing the heat dissipation speed.
Please be sure not to use the product equipment or socket or other places in high or easy to fall, so
as to avoid damage.
Before opening the socket power supply, please be sure to turn off the load power switch of the
product equipment.
The company reserves the rights to improve product, upgrade technology and change parameters
without prior notice.
1. In order to protect the legitimate rights and interests of users, please carefully read the
instructions, disclaimers and safety instructions provided with this product before using it. The company
reserves the right to update the above documents. Please operate the product
according to the instructions and safety instructions.
2. Once you begin to use the product, you shall be deemed to have read, understood,
recognized and accepted all terms and contents of the product's instructions, disclaimers and
safety instructions. Users undertake to be responsible for their actions and all consequences.
User undertakes to use the product only for legitimate purposes and agrees to these terms and
any relevant policies or guidelines that the company may establish.
3. In the process of using this product, please strictly abide by and execute the requirements
including but not limited to the instructions and safety instructions. All personal injuries,
accidents, property losses, legal disputes and other adverse events that cause conflicts of
interest caused by violation of the safety instructions or irresistible factors shall be borne by
users themselves, and the company shall not assume any responsibility.
4. Safety instructions:
Chapter 7 Disclaimer
User's Manual | Microscope Camera HW Series
www.lanoptik.com
- 8 -

LANOPTIK TECHNOLOGIES LTD
No. 72 Hongjing Street, Lejia Road, Baiyun District, Guangzhou, China. 510400
Phone: [phone] | Fax: [phone]
Website: http://www.lanoptik.com | Email: [e-mail]
Specifications are subject to change without any obligation on the part of the manufacturer.