Lanoptik HD1210 Series User manual

HD1210 Series Camera
User’s Manual
www.lanoptik.com

Content
www.lanoptik.com
CHAPTER 1 NOTES AND SAFETY REQUIREMENTS
1.1 CAUTIONS AND NOTES
CHAPTER 2 SOFTWARE SYSTEM REQUIREMENTS
2.1 SYSTEM REQUIREMENTS UNDER USB WORK MODE
CHAPTER 3 PACKING LIST
CHAPTER 4 FUNCTION INTRODUCTION OF EACH PART
4.1 NAME AND FUNCTION FOR EACH PART OF THE CAMERA
CHAPTER 5 PRODUCT ASSEMBLY GUIDE
5.1 CAMERA ASSEMBLY
5.1.1 Assembly with biological microscope
5.1.2 Disassembly the Camera
CHAPTER 6 INSTRUCTIONS
6.1 SOFTWARE INSTALLATION
6.1.1 USB working mode
6.1.2 WiFi working mode
6.2 DEVICE CONNECTION
6.3 METHOD OF PARFOCALIZING
6.4 START TO USE
CHAPTER 7 DISCLAIMER
- 1 -
- 1 -
- 2 -
- 2 -
- 3 -
- 4 -
- 4 -
- 5 -
- 5 -
- 5 -
- 5 -
- 6 -
- 6 -
- 6 -
- 6 -
- 6 -
- 6 -
- 6 -
- 7 -

To avoid danger or damage incurred to the lens, do not touch the lens or sensor directly with your
fingers.
Chapter 1 Notes and Safety Requirements
1.1 Cautions and Notes
User's Manual | Microscope Camera HD1210 Series
To avoid failure or electric shock hazard and so on, do not disassemble or modify the internal
structure of the device.
Do not plug in or unplug the Power connection port when hands are wet.
Do not use alcohol and other organic solvents to clean.
If the lens or sensor is dirty or damp, you should better use dry and non-linen fabric or professional
lens tissue to wipe them. To avoid scratches on the surface, do not touch the lens with your fingers.
Wipe the lens or sensor lightly.
The products are not specifically designed for an outdoor use. Do not expose it to outdoor
environment without any protection. Excessive temperature and humidity will damage the lens.
Please avoid using the product under the following environment: high temperature or high humidity
environment, places with direct sunlight, dirt or vibration and places near heat source.
Please use and store in the following environment:
Operating temperature ： 0℃~ 40℃
Storage temperature ： -20℃~ 60℃
Operating Humidity ： 30~60%RH
Storage Humidity ： 10~80%RH
If any foreign matter, water or liquid enter into the device by accident, disconnect the Power line
immediately. Please send it to the maintenance center and do not use the hair dryer to dry it by
yourself.
To prevent microscope from being tripped over or dropped, please put away the device’s connect
cable in use or standby.
To avoid electric shock by accident, please power off microscope before you move your computer or
laptop.
The cleanliness of the device lens will directly affect clarity degree of contents from the computer
screen during preview. Problems like various circles or spots on the screen may mostly be incurred
by dirt on the lens. When cleaning, please use professional lens tissue or other professional detergent
to clear the dirt on the lens.
Registered trademark and copyright: Copyright ownership of this produc belongs to Lanoptik
Technologies Ltd. Without written authorization of this company, any organizations or individuals
shall not photocopy, print, or translation to another language to any part of this document.
www.lanoptik.com
- 1 -

Windows 7 (64bit), Windows 8 (64bit), Windows 8.1 (64bit), Windows 10 (64bit) , Windows 11 (64bit)
2.2 System Requirements under WiFi Work Mode
2.1 System Requirements under USB Work Mode
Chapter 2 Software System Requirements
User's Manual | Microscope Camera HD1210 Series
Dual core 3GHz or higher CPU
USB 2.0 high-speed interface or USB2.0 compatible interface
At least 10 GB available hard-disk space
8G or more memory
DVD-ROM driver (only needed when installing software)
5.0 or above version for Android system.
8.0 or above version for IOS system.
Wireless network hardware must support the 802.11ac protocol (5G WiFi mode).
www.lanoptik.com
- 2 -

Paper QR code. Link address
1.WiFi DigiCamera
USB Power adaptor
2.Hexagon key
Chapter 3 Packing List
User's Manual | Microscope Camera HD1210 Series
www.lanoptik.com
- 3 -

7.Focusing screw
2.HDMI interface
4.Power indicator
6.ACT indicator light
1.Network interface (After connecting to the Internet, the wireless device (mobile phone, tablet, PC, etc.)
connects to the camera WiFi signal, which can realize the connection between the
wireless device and the camera and the Internet at the same time.)
3.USB cable (Under USB work mode
： connect with PC to realize data transmission, and PC can live-stream
image through software.
Under WiFi work mode ： connect to USB power plug to realize power supply to the Camera. The
wireless device can connect to the Camera WiFi to live-stream image.)
5.Power on/off OFF
： The Camera will stop working.
USB Working mode ： It will allow the Camera connect to PC via. USB cable.
WiFi Working mode ： It will allow the Camera connect to smart phones/tablets via. WiFi.)
4.1 Name and Function for Each Part of the Camera
8.Dovetail slot
Chapter 4 Function Introduction of Each Part
User's Manual | Microscope Camera HD1210 Series
www.lanoptik.com
- 4 -

5.1.2 Disassembly the Camera
Chapter 5 Product Assembly Guide
5.1 Camera Assembly
5.1.1 Assembly with biological microscope
1. Take out the dust cover of the trinocular microscope, as shown in figure 5-5-1:
1) Loosen the fixing screw of the dust cover of the trinocular microscope;
2) Take out the dust cover of the microscope dovetail slot.
2. Camera installation
1) Place the camera to the dovetail slot of the microscope, as shown in figure 5-5-2;
2) Tighten the fastening screw on the microscope dovetail slot and fix the camera on the microscope.
Fig. 5-5-1 Fig. 5-5-2
1 ． Reverse the assembly sequence
User's Manual | Microscope Camera HD1210 Series
www.lanoptik.com
- 5 -

Chapter 6 Instructions
User's Manual | Microscope Camera HD1210 Series
6.1 Software Installation
6.1.1 USB working mode
Through the download links provided with the packing box, please download Pixit Pro software.
For the specific operation of software, please refer to the "User Manual of Pixit Pro_English"
6.1.2 WiFi working mode
1. Install KoPa WiFi Lab for Android system.
Method 1: Download KoPa WiFi Lab through the download links provided with the packing box.
Method 2: copy “KoPa WiFi Lab for Android”apk into Android system for installation.
2. Install “KoPa WiFi Lab”for iOS:
Download and install the “KoPa WiFi Lab” on apple's APP Store.
6.2 Device connection
Plug the USB-A port of the USB cable into the USB port of computer.
Switch the Camera to USB working mode.
Run KoPa Capture Pro software if you are using.
1. USB working mode
For the specific operation of software, please refer to the "User Manual of Pixit Pro _English"
Connect the USB cable to the supplied USB power plug.
Switch the Camera to WiFi working mode. After about 20 seconds, the WiFi work indicator in the
Camera stops flashing and stays on.
Connected to WiFi name: WiFiCamera_5G_xxxxxx and input password: 12345678 to your smart
phones/tablets.
Run the APP "KoPa WiFi Lab"
2. WiFi working mode
Connect the USB cable to the USB power plug to supply power to the camera.
Turn the camera's toggle switch to the "USB" or "WiFi" position.
Connect the camera to the HDMI display with an HDMI cable, and turn on the HDMI display to display
the HDMI output.
3. HDMI working mode
www.lanoptik.com
- 6 -
6.3 Device connection
Place a specimen on the microscope table and adjust the eyepiece diopter to the minimum value.
Using a 10X objective lens, it is recommended to focus on any black spot/or the darkest spot on the
section until it is most clear.
(Use the hexagon key to finely turn the focusing screw (adjust the focus length), until live preview
from the software is clear, parfocalizing is done now.
6.4 Start to use
The camera is ready

Please do not use wet hands to plug and unplug the power supply of the equipment.
Please be sure to use a regular brand power socket, and make sure the grounding is well grounded to
prevent electric shock.
Please be sure to make regular safety checks on sockets and plugs to avoid potential electrical
safety hazards caused by aging and short circuit.
Please be sure not to use the product in a humid or hot environment to ensure the safety of the
product.
Please be sure to loosen bundle cords of the power cable before using, to avoid electromagnetic
induction and heating, thus increasing the heat dissipation speed.
Please be sure not to use the product equipment or socket or other places in high or easy to fall, so
as to avoid damage.
Before opening the socket power supply, please be sure to turn off the load power switch of the
product equipment.
The company reserves the rights to improve product, upgrade technology and change parameters
without prior notice.
1. In order to protect the legitimate rights and interests of users, please carefully read the
instructions, disclaimers and safety instructions provided with this product before using it. The company
reserves the right to update the above documents. Please operate the product
according to the instructions and safety instructions.
2. Once you begin to use the product, you shall be deemed to have read, understood,
recognized and accepted all terms and contents of the product's instructions, disclaimers and
safety instructions. Users undertake to be responsible for their actions and all consequences.
User undertakes to use the product only for legitimate purposes and agrees to these terms and
any relevant policies or guidelines that the company may establish.
3. In the process of using this product, please strictly abide by and execute the requirements
including but not limited to the instructions and safety instructions. All personal injuries,
accidents, property losses, legal disputes and other adverse events that cause conflicts of
interest caused by violation of the safety instructions or irresistible factors shall be borne by
users themselves, and the company shall not assume any responsibility.
4. Safety instructions:
Chapter 7 Disclaimer
User's Manual | Microscope Camera HD1210 Series
www.lanoptik.com
- 7 -

LANOPTIK TECHNOLOGIES LTD
No. 72 Hongjing Street, Lejia Road, Baiyun District, Guangzhou, China. 510400
Phone: [phone] | Fax: [phone]
Website: http://www.lanoptik.com | Email: [e-mail]
Specifications are subject to change without any obligation on the part of the manufacturer.