Lantronix xSenso 21R2 User manual

WHAT’S
INSIDE
Rubber Feet (4)
xSenso™ 21R2 Wall Mount BracketQuick Start Guide
1 HARDWARE REVIEW
2 HARDWARE INSTALLATION
DIN Rail Mount
1. Angle the xSenso™ to position and
hook onto the DIN rail, then push it
back until it is flat against the DIN
rail. Push the orange clip upwards to
secure.
2.To remove from DIN rail, pull the
orange clip downward to unlock.
Angle and lift the xSenso™ upwards
to unlatch and remove.
Desktop, shelf, or table top installation
1. Place xSenso™ upside down on a smooth, flat surface.
2.Peel off the rubber feet from the adhesive strip and place them
adhesive-side down onto each corner of the xSenso™ device.
3.Turn the xSenso™ over so that it is resting on the rubber feet.
Mini USB Port
For management
and configuration of
xSenso™ device
Relay 1
Analog
Input 2
Relay 2
Analog
Input 1
9-30VDC Terminal
Block Power Input
9-30VDC Barrel Locking Power Input
NO = Normally Open
NC = Normally Closed
COM = Common Ground
Input Current I = 0-20mA
Input Voltage V = ±100mV, ±1V, ±10V
Excitation P = 15VDC, 10mA per channel or 20mA total
= Ground
10/100 Mbps
(Auto-MDIX)
Ethernet port
Reset pin
Input 1 and
Input 2
status LED
Output 1 and
Output 2
status LED
WHAT’S
INSIDE
RubberFeet (4)
xSenso™21R2 WallMount BracketQuickStart Guide
1 HARDWARE REVIEW
2 HARDWARE INSTALLATION
DINRail Mount
1.Angle the xSenso™ to position and
hookonto the DIN rail, then push it
backuntil it is flat against the DIN
rail. Push the orange clip upwards to
secure.
2.Toremove from DIN rail, pull the
orangeclip downward to unlock.
Angleand lift the xSenso™ upwards
tounlatch and remove.
Desktop,shelf, or table top installation
1.Place xSenso™ upside down on a smooth, flat surface.
2.Peel off the rubber feet fromthe adhesive strip and place them
adhesive-sidedown onto each corner of the xSenso™ device.
3.Turnthe xSenso™ over so that it is resting on the rubber feet.
MiniUSB Port
Formanagement
andconfiguration of
xSenso™device
Relay1
Analog
Input2
Relay2
Analog
Input1
9-30VDCTerminal
BlockPower Input
9-30VDCBarrel Locking Power Input
NO =Normally Open
NC =Normally Closed
COM = CommonGround
InputCurrent I = 0-20mA
InputVoltage V = ±100mV,±1V, ±10V
Excitation P= 15VDC, 10mA per channel or 20mA total
= Ground
10/100Mbps
(Auto-MDIX)
Ethernetport
Resetpin
Input1 and
Input2
statusLED
Output1 and
Output2
statusLED
WHAT’S
INSIDE
RubberFeet(4)
xSenso™21A2 WallMountBracketQuickStartGuide
1HARDWAREREVIEW
2HARDWAREINSTALLATION
DINRailMount
1.AnglethexSenso™topositionand
hookontotheDINrail,thenpushit
backuntilitisflatagainsttheDIN
rail.Pushtheorangeclipupwardsto
secure.
2.ToremovefromDINrail,pullthe
orangeclipdownwardtounlock.
AngleandliftthexSenso™upwards
tounlatchandremove.
Desktop,shelf,ortabletopinstallation
1.PlacexSenso™upsidedownonasmooth,flatsurface.
2.Peelofftherubberfeetfromtheadhesivestripandplacethem
adhesive-sidedownontoeachcornerofthexSensodevice.
3.TurnthexSenso™oversothatitisrestingontherubberfeet.
MiniUSBPort
Formanagement
andconfigurationof
xSenso™device
Analog
Output1
Analog
Input2
Analog
Output2
Analog
Input1
9-30VDCTerminal
BlockPowerInput
9-30VDCBarrelLockingPowerInput
OutputCurrentI=0-20mA
OutputVoltageV=0-10V
=Ground
InputCurrentI=0-20mA
InputVoltageV=±100mV,±1V,±10V
ExcitationP=15VDC,10mAperchannelor 20mA total
=Ground
10/100Mbps
(Auto-MDIX)
Ethernetport
Resetpin
Input1and
Input2
statusLED
Output1and
Output2
statusLED
WHAT’S
INSIDE
xSenso™21A2QuickStartGuide
xSenso™21A2QuickStartGuide
xSenso™21R2 Quick Start Guide
xSenso™21R2 Quick Start Guide

xSenso™21R2 Quick Start Guide
4 DEVICE DISCOVERY OVER NETWORK
INSTALL DEVICE INSTALLER
REQUIREMENTS: Computer must have a working Ethernet adapter
running Windows as the Operating System (OS). For device discovery,
the computer and device should be connected to the same IP subnet.
1. Download the latest version of DeviceInstaller from
http://www.lantronix.com/downloads. The minimum required
version for DeviceInstaller is 4.3.0.8.
2. Run the executable to start the installation process on the computer
being used to configure the xSenso.
3. Follow the installation wizard prompts.
1. Run DeviceInstaller
Click: Start > Programs > Lantronix > DeviceInstaller > DeviceInstaller.
2. Upon launch, DeviceInstaller will search for Lantronix devices on the
network. Select the unit from the list of Lantronix devices on the
local network. (You may also click on the Search icon if your device
isn’t found immediately)
3. Click the Assign IP icon.
4. If prompted, enter the MAC address (on the product label) and click
Next.
5. Select Assign a Specific IP address and click Next.
6. Enter the IP Address. The Subnet Mask displays automatically based
on the IP address. If desired, you may change it. On a local network,
you can leave the Default Gateway blank (all zeros). Click Next.
7. Click the Assign button and wait several seconds until a confirmation
message displays. Click Finish.
8. Click on the Search icon and DeviceInstaller locates the unit and
adds it to the list.
If DeviceInstaller is unable to discover the xSenso™:
• InWindowsDeviceManager,ensurethattheEthernetadapteris
installed and working properly.
• IfyourPCorlaptophasmorethanonenetworkinterface,makesure
the correct interface is selected in DeviceInstaller.
•GotoTools>Options and make sure the correct network interface is
selected. If not, check the correct interface, click on OK, and restart
DeviceInstaller.
•ChecktheLEDindicatoronthexSenso™tomakesurethereisa
physical connection between the Ethernet adapter and the xSenso.™
Once the xSenso™ is in the device list, it can be configured.
1. Double-click the unit in the list. Details about the unit will be
displayed.
2.Select the Web Configuration tab and click on the green arrow. You
will be prompted for a username and password.
3.The default USER ID = admin and PASSWORD = PASS (both are case
sensitive)
For additional configuration, please refer to the xSenso™ User Guide for
detailed instructions: http://www.lantronix.com/support/downloads
© 2012 Lantronix, Inc. Lantronix and xSenso are trademarks of Lantronix, Inc. All other trademarks and trade names are the property of their respective holders. Specifications subject to
change without notice. 900-656-R Rev A 11/12
Contact Technical Support
For technical support queries, visit http://www.lantronix.com/support or call [phone] Monday – Friday from 6:00 a.m. – 5:00 p.m., Pacific
Time, excluding holidays.
Latest Firmware For the latest firmware downloads, visit http://www.lantronix.com/support/downloads
IP Address Assignment Tutorial To view a tutorial on how to assign an IP address, visit http://www.lantronix.com/support/tutorials
5 IP ADDRESS CONFIGURATION
6 COMPLETE THE CONFIGURATION
POWER REQUIREMENTS
NOTE: xSenso™ does not come with an external power supply. Power
supplies may be purchased as separate accessories. Refer to the User
Guide for part numbers.
1. Connect a power source to the terminal block or the locking barrel power
connector. Both power connectors support an input power source of
9-30VDC. Both may be used simultaneously for power redundancy.
2.Connect an Ethernet cable between the LAN port on the xSenso™ and
a network switch or router.
THIS COMPLETES THE HARDWARE INSTALLATION.
3 INSTALLATION