LAON TECHNOLOGY LT150 MOBILE User manual

ⓒ2017 LaON Technology Co., Ltd. All rights reserved.
LT150 MOBILE
Digital Wireless Intercom System
Operating Instructions
(V2.3 171101)
LaON Technology Co., Ltd.
www.laon-tech.com

ⓒ2017 LaON Technology Co., Ltd. All rights reserved.
TABLE OF CONTENTS
IMPORTANT SAFETY INFORMATIONS
2
SECTION 1. INTRODUCTION
4
SYSTEM USAGE EXAMPLE
6
SECTION 2. PRODUCT OVERVIEW
9
MS150 MOBILE STATION EQUIPMENTS
9
BP150 BELT PACK EQUIPMENTS
10
BATTERY CHARGER AND HEDSET EQUIPMENTS
10
EQUIPMENTS OVERVIEW
12
MS150 MOBILE STATION OVERVIEW
12
BP150 BELT PACK OVERVIEW
13
LT150 MOBILE SYSTEM MENUS
14
SECTION3. SYSTEM SETUP AND CONNECTIONS
16
MS150 MOBILE STATION SETUP
16
BP150 BELT PACK SETUPAND PAIRING UP
17
BELT PACK SETUP
17
PAIRING UP BELT PACKS
18
BATCHG125 BATTERY CHARGER SETUP
19
BRK150 MOUNT KIT INSTALLATION
19
SECTION 4. SYSTEM OPERATION
20
MS150 MOBILE STATION OPERATION
20
AUXILIARY DEVICE SETUP
27
BP150 BELT PACK OPERATION
28
SECTION 5. FAQ AND TROUBLE SHOOTING
36
MOBILE STATION
36
BELT PACK
37
SECTION 6. APPENDIX
38
FACTORY DEFAULT SETTING AND RECOMMENDATION
38
6-PIN HEADSET CABLE CONNECTOR
38
SECTION 7. TECHNICAL SPECIFIACTIONS
39
LT150 SYSTEM SPECIFICATIONS
39
MS150 MOBILE STATION
39
BP150 BELT PACK
40

ⓒ2017 LaON Technology Co., Ltd. All rights reserved. 2
IMPORTANT SAFETY INFORMATIONS
1. For LT150 systems, to reduce the risk of electric shock, explosion or fire;
Use only the supplied AC power adapter
Do not disassemble the product
Avoid contact with liquids besides the permitted certain equipments
Use only the proper type of battery and rechargeable battery supplied by the manufacturer
2. Battery Safety and Cautions
Do not charge with any other AC power adapter or charger.
Do not burn, disassemble, bend or short-circuit the battery.
Dispose of used up battery promptly and safely according to local regulations.
Keep battery away from children.
Do not short the metal contacts with electrically conducting material such as bracelets, keys, and etc.
Recommended battery storage temperature is -20 °C to 30°C for less than 1 year, -20°C to 40°C for less than 90
days, -20 °C to 50°C for Less than 30 days.
Recommended Battery charging temperature is 0°C to 40°C
Do not burn or expose batteries to excessive heat such as sunshine or other heat sources
When using alkaline or other maker‟s rechargeable batteries other than LAON provided rechargeable batteries,
LTWI-BAT50 and LTWI-BAT150, use the same batteries as packaged by the makers for the same specifications,
related current and voltage. In case of using non-LAON provided rechargeable batteries, use the maker designated
battery charger. Two or Four batteries to be used together by putting into the Battery Sled of LAON products should
be managed to have the same residual time, life and recharged with same cycles. Using batteries together with
different specifications and natures may cause damages on inner parts of the applicable LAON product and affect
battery operating time.
3. Antenna Safety and Cautions
Use only manufacturer supplied antennas.
Antenna shall be mounted in such a manner to minimize the potential for human contact during normal operation. The
antenna should not be contacted during operation. The minimum separation distance of 7.9 inches (20 cm) from the
antenna to the body of user required.

ⓒ2017 LaON Technology Co., Ltd. All rights reserved. 3
LT150 system operates in the 5GHz UNII band frequency range. LT150 system is approved for license free use in most countries.
There may be restrictions on the use of some bands or RF spectrum operations in some countries. Therefore, it is your
responsibility to confirm with the designated authorizer in your local area whether the equipments of the LT150 system approved to
use in your country or not.
NOTICE
Illustrations, figures and images of this publication are only for explaining equipment‟s operations and functions and may
roughly reflect the actual equipment.
Contact the designated distributors or retailers to avoid erroneous interpretations or language translations that may cause
equipment malfunctioning.
The information herein, including but not limited to, illustrations, figures and images subject to change without prior notice and
shall not be interpreted as an expressed or implied commitment on LAON Technology‟s part.
With due respect, LAON Technology, the manufacturer of the equipment does not provide any expressed or implied warranty to
anything included in this operating instruction and shall have no legal responsibility for any implied warranties of suitableness
for a specific application or for any special, indirect, or consequential damages.
LAON Technology may update this publication at its own discretion.

ⓒ2017 LaON Technology Co., Ltd. All rights reserved. 4
SECTION 1: INTRODUCTION
LaON Technology(„LaON‟)‟s patent-technology base digital wireless intercom system offers the best audio quality with an excellent
clarity by using 5GHz UNII band, triple diversity - frequency, time and antenna, and frequency interference avoidance
technologies. It guarantees the system stability even in the large congested site environments where various A/V and wireless
equipments are co-located. With LT150 system‟s Mobile Station „MS150‟, users can install the Station at the fixed place or use
in mobile with a battery. In addition, external devices such as a speaker and microphone can be connected with the Mobile
Station through Auxiliary In/Out interface. The Mobile Station can be operated in a Belt Pack mode for the LT750‟s Base
Station „BS750 and the Auxiliary In/Out activation mode is still available when it is staying in a Belt Pack mode. LT150 Mobile
System provides the equivalent audio quality and performance to the highest range system, LT750 Expert System that is
used for professional applications.
LT150 MOBILE SYSTEM MAIN FEATURES
LICENSE-FREE 5GHz UNII BAND
5GHz UNII Band, the worldwide license-free frequency band provides approximately up to 29 RF channels depending on
the regions as opposed three (3) RF channels on 2.4GHz ISM band. Therefore, users are able to enjoy pleasant wireless
communications with even less traffics or interferences. Due to high frequency band, the system is also hardly affected
by high-power digital equipments such as amplifiers and speakers.
INDUSTRY-TOP LEVEL AUDIO QUALITY
23ms low latency level and 7.2KHz audio frequency guarantee a high quality audio performance. LT150 system is
perfectly tuned professional wireless intercom system that fits to use at various loud and congested site environments.
TWO(2) COMMUNICATION GROUP CHANNEL
Up to two(2) group communication channels can be allocated for both of Mobile Station and each Belt Pack.
FIVE(5) FULL-DUPLEX LISTEN & TALK COMMUNICATION CHANNEL (1 MS + 4 BPs)
Five (5) full-duplex audio channels are offered with one (1) Mobile Station.
UP TO ONE HUNDRED AND TWENTY EIGHT(128) BELT PACK CONNECTION
One hundred and twenty eight (128) Belt Packs can be registered into a Mobile Station.
MOBILE STATION
The Station is compact and can be operated either by a rechargeable battery pack or AA type alkaline battery( x 6) with a
LaON provided battery sled.
BELTPACK IN MASTER MODE
A Belt Pack can play a role as a master where there is no Mobile Station or the Mobile Station is located far from the
actual Belt Pack operation area.
AUXILIARY I/O INTERFACES
Auxiliary Input / Output ports are provided to secure seamless connections with wired intercom systems, external audio
devices and etc.
COMPACT DESIGN
Comfortable headset and compact Belt Pack with internal antenna support high wearability with mobility even at the
tough broadcasting or event sites.
VARIOUS OPTIONS ON BATTERY
Either LaON provided rechargeable battery or AA type alkaline battery with LaON provided battery sled can be used for
supplying power to the Belt Pack. Also, non-LaON provided rechargeable battery can be used with the battery sled.
MONITORING FUNCTIONS
Belt Pack provides various monitoring functions such as the link status, RSSI(Received Signal Strength Indication),
battery status and etc.
MONITORING OF AUDIO BREAK-UP
When a Belt Pack is out of coverage, the Belt Pack user is easily able to monitor the audio break-up with his/her side
tone.

ⓒ2017 LaON Technology Co., Ltd. All rights reserved. 5
TOP SECURITY WITH AES 256BIT LEVEL 3 ENCRYPTION
AES 256bit Level 3, the top level encryption technology is applied to secure confidential communications.
EFFICIENT 7 PORT CHARGER
There are five (5) bays for charging the Belt Pack batteries which are equipped in the Belt Packs and two (2) bays for
charging the Belt Pack batteries which are separated from the Belt Packs. Two (2) of them are for dual use for charging
Remote Station or Mobile Station‟s batteries.
LaON IN-HOUSE TECHNOLOGIES AND SOLUTIONS
LaON has developed from the wireless SoC built in the systems to the wireless intercom systems in-company by
applying its own patent base technologies. Base on the know-how and comprehensive experiences in wireless
technology, LaON offers timely and prompt service with full flexibilities for customer satisfactions with top priority.
SYSTEMS AT A GLANCE
(BS:Base Station / MS:Mobile Station / BP:Belt Pack / RBS:Remote Station)
LT SERIES
LT750
(From July 2016)
LT550
LT250
LT150
(From July 2016)
SYSTEM
Frequency band
5GHz UNII
5GHz UNII
5GHz UNII
5GHz UNII
Station type
Fixed
Fixed
Fixed
Fixed or Mobile
Battery availability for Station
Ｘ
Ｘ
Ｘ
O
Number of full-duplex channel
11(1BS + 10BP)
11(1BS + 10BP)
9(1BS + 8BP)
5(1MS + 4BP)
Number of group channel
5
5
3
2
4-Wire port
O(1)
O(1)
Ｘ
Ｘ
Auxiliary I/O port
O(1)
O(1)
O(1)
O(1)
Number of RBS connection
10
5
1
Ｘ
Audio Frequency
200 Hz~7.2kHz
200 Hz~3.5kHz
200 Hz~3.5kHz
200Hz~7.2KHz
Speaker Output
400mW
250mW
250mW
400mW
BP connection and compatibility
BP750, MS150
BP550
BP250, BP550
BP150, BP750
Number of BP connection
128
128
128
128
Link, RSSI, Battery status Monitoring
O (BS, BP)
O (BS, BP)
O(BS, BP)
O(BP)
RF monitoring
O
O (USB S/W)
Ｘ
O
BP # for group channel allocation
128
32
32
128
BELT PACK
Two groups communication (IC/ISO)
O
O
O
O
Side tone level adjustment
O
Ｘ
Ｘ
O
Key lock
O
Ｘ
Ｘ
O
Hands off sensitivity level selection
O
O
O
O
Low cut adjustment
O(-3dB/-6dB)
Ｘ
Ｘ
O(-3dB/-6dB)
Maser BP function
O
Ｘ
Ｘ
O

ⓒ2017 LaON Technology Co., Ltd. All rights reserved. 6
SYSTEM USAGE EXAMPLE
COMMUNICATION GROUP ALLOCATION
For Mobile Station, up to two(2) groups can be allocated and either one group can be selected at once
On Belt Pack, communication in each individual group or both two groups is available.
On Mobile Station, the group channel setup and volume control will be applied the same to the device which is connected
through auxiliary In/Out interface.
IC/ISO communications in ONE (1) system
Group 1 & 2
Group 1
Auxiliary or
4-Wire device
Group 1
BP1
BP2
BP10
BP17
BP28
BP127
BP128
…
…
…
Group 1: IC
Group 2 : ISO
MS150
Mobile Station
BP1
BP2
BP4
BP3
BP5
BP10
BP28
BP17
BP127
BP128
Group 1 or 2
Group 1 or 2
Group 1 or 2
Auxiliary Device
Headset
…
…
MS150
Mobile Station
…
…

ⓒ2017 LaON Technology Co., Ltd. All rights reserved. 7
SYSTEM USAGE OF THE STAND-ALONE OPERATION
SYSTEM USAGE WITH LT750 EXPERT SYSTEM
SYSTEM USAGE WITH WIRED INTERCOM SYSTEM / MATRIX (MS150 in „MS‟ MODE)
INTERCOM PANEL
INTERCOM PANEL
INTERCOM PANEL
MATRIX
INTERCOM
…
MS150
Mobile Station
…
…
BP1 BP128
BP1 BP128
BP1 BP128
BP1 BP128
…
MS150
Mobile Station
MS150
Mobile Station
MS150
Mobile Station
BP1
BP2
BP4
BP3
BP127
……..
MS150 Mobile Station
in Belt Pack mode
Auxiliary devices
(SPK, Microphone etc)
BS750 Base Station
BP128
BP1
BP2
BP4
BP3
BP127
BP128
……..
MS150 Mobile Station

ⓒ2017 LaON Technology Co., Ltd. All rights reserved. 8
SYSTEM USAGE WITH WIRED INTERCOM SYSTEM / MATRIX (MS150 in „BP‟ MODE)
MASTER BELT PACK (MB) MODE
A Belt Pack can be set in Master Mode to replace the Mobile Station.
In the Master Belt Pack Mode, the system provides a single communication group channel with five (5) full-duplex audio
communication channels (1 MB + 4 BPs).
Automatic handoff is available between the Mobile Station and Master Belt Pack if they are located in independent
separate area respectively. All Belt Packs to be linked to the Master Belt Pack should mandatorily be set the group
channel to one (1).
Stand-alone operation in each independent area
NOTE: Do not use Mobile Station and Master Belt Pack(MB) in a same coverage. Otherwise, the Belt Packs will be
automatically linked to either one with stronger signal which will cause confusion and wrong operation on the wireless
communication.
……..
BP1
BP2
BP3
BP4
BP127
BP128
BP150 Belt Pack
……..
BP1
BP2
BP3
BP4
BP127
BP128
BP150 Belt Pack
Master Belt Pack (MB)
Link with BPs in communication group channel 1
Automatic or manual handoff between MS and MB
Five (5) full-duplex audio communication channels
MS150 Mobile Station (MS)
MS150
Mobile Station
in BP mode
Auxiliary
(Group#3)
BP1
BP2
BP3
BS750
Base Station
Auxiliary
(Group#1)
4-Wire
(Group#2)
……..
BP127
BP128
BP126
Auxiliary
(Group#4)
MATRIX
INTERCOM

ⓒ2017 LaON Technology Co., Ltd. All rights reserved. 9
SECTION 2: PRODUCT OVERVIEW
LT150 SYSTEM EQUIPMENTS
The followings are basic LT150 Wireless Intercom System equipments.
MS150 MOBILE STATION EQUIPMENTS
Mount kit „BRK150‟ enables to fixed install the Mobile Station onto the wall or camera tripod.
Mount kit, BRK150
BAT150 Rechargeable battery (optional)
Battery sled
MS150 Mobile Station
Mobile Station Antenna
AC power adapter

ⓒ2017 LaON Technology Co., Ltd. All rights reserved. 10
BP150 BELT PACK EQUIPMENTS
BATTERY CHARGER AND HEDSET EQUIPMENTS
BATCHG125 BATTERY CHARGER EQUIPMENTS
AC Power Supply
BATCHG125 Battery Charger
BAT50 Rechargeable Battery Pack (Optional)
Battery sled
BP150 Belt Pack
BPPCH100 Belt Pack Pouch (Optional)

ⓒ2017 LaON Technology Co., Ltd. All rights reserved. 11
HEADSETS
LMH-10 (Dynamic)
PTE-850 (Electret)
LSH-S125 (Electret)
LMH-125 (Electret)
LMH-125D (Dynamic)

ⓒ2017 LaON Technology Co., Ltd. All rights reserved. 12
EQUIPMENTS OVERVIEW
MS150 MOBILE STATION OVERVIEW
1. Antenna connector
10. Battery cover
2. Antenna connector
11. AUX Input Line / Mic. level selection switch
3. OLED Display
12. AUX IN connector
4. Headset TALK button with indicator light
13 .AUX OUT connector
5. Control button
14. 12V DC POWER connector
6. Headset communication group button
15. Power switch
7. Headset speaker volume control (UP)/Menu selection button
16. Headset cable connector (Receptacle)
8. Menu SET button
9. Headset speaker volume control (DOWN)/Menu Selection button
17. Mount kit hole
Figure 2-1. Panels of the Mobile Station
2
4
3
5
9
8
10
7
6
1
12
13
14
15
11
17
16

ⓒ2017 LaON Technology Co., Ltd. All rights reserved. 13
BP150 BELT PACK OVERVIEW
BP150 Belt Pack is moisture resistant which is excellent in using under humid environment.
1. Headset cable connector (Receptacle)
7. Menu SET button
2. OLED display
8. Headset speaker volume control (DOWN) / Menu selection button
3. Headset TALK button with indicator light
9. Belt clipper
4. Power (PWR) button
10. Battery cover
5. Headset comm. group (GRP) button/
TALK button in TWO GROUPS mode
11. Charger terminals (Bottom of the Belt Pack)
6. Headset speaker volume control (UP) /
Menu selection button
Belt Pack pairing setup key: „PWR + SET‟
Manual handoff key: „PWR + PWR‟ (Double click of PWR)
BELT PACK CHARGER TERMINAL SPECIFICATION
NOTE
Do not stand the Belt Pack direct on electric conductors such as bracelets, keys and etc. and do not short the metal
contacts on the bottom of the Belt Pack with those electrically conducting material.
It is necessary to store the battery after fully charged and separating from the Belt Pack.
Turn off the Belt Pack before charging.
1
2
1. –
2. Temperature sensor
3. +
3
Figure 2-2. Panels of the Belt Pack
9
10
11
1
4
2
7
3
5
6
8

ⓒ2017 LaON Technology Co., Ltd. All rights reserved. 14
LT150 MOBILE SYSTEM MENUS
MS150 MOBILE STATION MENU („MS‟ MODE)
Below is the menu operation with the Mobile Station
Pressing SET button on the NORMAL menu will lead you to MAIN menu.
On MAIN menu, press UP/DOWN direction key to move to the next menus.
Pressing CTRL button once on any menu screen will lead you to the NORMAL menu.
BP150 BELT PACK MENU
Pressing SET button on the NORMAL menu will lead you to MAIN menu.
On MAIN menu, press UP/DOWN direction key to move to the next menus.
Pressing PWR button once on any menu screen will lead you to the NORMAL menu.
In Two Groups set mode, the Speaker Volume adjustment will be available for each group individually.
Belt Pack menus shown sequentially
BP150
MS
MB
<NORMAL menu>
<MAIN menu>
SPEAKER VOLUME adjustment menu in TWO GROUPS set mode
<MAIN menu>
<NORMAL menu>
MS150
MS
MS150
CH:11
Menus in Mobile Station (MS) mode shown sequentially

ⓒ2017 LaON Technology Co., Ltd. All rights reserved. 15
MS150 MOBILE STATION MENU IN BELT PACK („BP‟) MODE
Below is the menu operation of the Mobile Station when it is staying in a Belt Pack mode for the LT750‟s Base Station, BS750.
BP150 BELT PACK MENU IN MASTER BELT PACK („MB‟) MODE
Below is the menu operation of the Belt Pack when it is staying in Master Belt Pack mode.
MB
MB
MB
CH:11
<NORMAL menu (Master Belt Pack)>
<MAIN menu>
Master Belt Pack menus shown sequentially
MS-BP
Mobile Station‟s menus in Belt Pack mode shown sequentially
MS
<NORMAL menu>
<MAIN menu>

ⓒ2017 LaON Technology Co., Ltd. All rights reserved. 16
SECTION 3: SYSTEM SETUP AND CONNECTIONS
MS150 MOBILE STATION SETUP
Following is how to set up LT150 Mobile System.
Step 1: Put two enclosed antennas to the antenna connectors (#1 and #2) on the upper panel of the Mobile Station. Turn the
sleeve on each of the antenna connectors clockwise to tighten them, and ensure that the antennas are connected firmly.
NOTE 1: These two antennas must be positioned vertically and be folded completely as 90 degree. Otherwise, it will be
caused to weaken the signal.
NOTE 2: While attaching the antennas directly to the rear panel of the Mobile Station, the Mobile Station should be away
from any metal obstructions, walls, and electronic equipments that can create radio interference. It is highly
recommended to place the antenna as high as possible in the center of the coverage and away from
obstructions.
Step 2: Supply the power to the Mobile Station.
When you use the wall-adapter power supply:
Plug the DC cable from the enclosed wall-adapter power supply into the 12VDC POWER connector (#14) on the
bottom of the Mobile Station. Plug the large female connector at the end of the AC power cord into the power supply
and plug the other end of theAC power cord into a standard wall outlet.
When you use the battery:
Pull the cover up to open the battery cover (#10) and put a fully charged rechargeable battery pack (BAT150) or battery
sled with six fresh AA 1.5v alkaline batteries. Make sure the position of polarity (+, -) is correct.
When both options are used at the same time, power adapter will automatically be used.
Step 3: The headset is with „Push-Pull Lock‟ type connector. Put a headset into the HEADSET connector (#16) on the bottom panel
of the Mobile Station. To disconnect the headset, hold the plug on the headset connector and pull out slightly turning.
Step 4: Press the POWER switch (#15) on the bottom panel of the Mobile Station and press CTRL button longer than 3 seconds to
turn on the Mobile Station. A voice message “Power on” will be heard from the headset, and the red TALK light adjacent
to the TALK button will go on. In MS mode, „DFS detecting‟ message will be indicated on the Mobile Station‟s upper panel
display for one (1) minute and once the detecting is completed, NORMAL menu with an indication „MS150‟ will pop up as
shown in Figure 3-2: After a few seconds, TALK light will be changed to green slow flashing, indicating the Mobile Station
is ready to use
See the MS150 MOBILE STATION OPERATION in SECTION 4 for details about the NORMAL menu.
Figure 3-2. NORMAL menu („MS‟ mode)
MS150
Figure 3-1. Panels of the Mobile Station
2
4
3
5
9
8
10
7
6
1
12
13
14
15
11
17
16

ⓒ2017 LaON Technology Co., Ltd. All rights reserved. 17
BP150 BELT PACK SETUP AND PAIRING UP
When you operate each Belt Pack for the first time with the Mobile Station, you must pair up the Belt Pack with a Mobile Station.
This pairing process allows a Mobile Station and a Belt Pack to recognize each other and an own cryptic code will be given for the
corresponding system. The Mobile Station will identify all the paired up Belt Packs and recognize the difference between the Belt
Packs. If a Belt Pack is added or replaced later, the new one is necessarily to be paired up with the Mobile Station.
Each Mobile Station allows up to one hundred twenty eight (128) Belt Pack connections.
BELT PACK SETUP
Before pairing up the Belt Pack with the Mobile Station, set up all Belt Packs as following steps:
Slide the cover down to open the battery cover (#10), and put a fully charged rechargeable battery pack (BAT50) or battery sled
with two fresh AA 1.5V alkaline batteries. Make sure the position of polarity (+, -) is correct. Close the battery cover.
9
10
11
1
4
2
7
3
5
6
8

ⓒ2017 LaON Technology Co., Ltd. All rights reserved. 18
PAIRING UP BELT PACKS
Check out the power status of the each Belt Pack‟s, which will be paired up with Mobile Station. To execute a paring process, the
Mobile Station and Belt Packs should be turned on. Belt Packs should not go further than 3 feet (1 meter) from the Mobile Station
while they are being paired.
NOTE: Once paring is completed, the Mobile Station and each Belt Pack should go further than 6.5 feet (2 meters) to operate
otherwise, there could be audio breakups.
READY FOR PAIRING PROCESSING WITH BELT PACK
Turn on the Belt Pack by pressing PWR button for 2 seconds and confirm the NORMAL menu is displayed. When a Belt Pack
is not paired up yet, the LED adjacent to the TALK button will be blinking in red.
EXECUTING PARING PROCESSING WITH MOBILE STATION AND BELT PACK
a. Confirm the initial screen of the Mobile Station is displayed on the OLED screen. If the screen is in a sleep mode, press
SET to wake it up. On Mobile Station, press and hold the SET button on the front panel just after pressing and holding the
CTRL button. By doing this, the Mobile Station will be in „pairing waiting mode‟ and the message, “Pairing…” will appears
shortly on the Mobile Station display and then you can release both buttons. In the pairing waiting mode, Mobile Station
waits a pairing requirement from the Belt Pack for 20 seconds, and during this time all communications between Belt
Packs will be halted.
b. With a Belt Pack to be paired up, confirm the initial screen is displayed otherwise press SET to wake it up from the sleep
mode and stay not further than 3 feet (1 meter) from the Mobile Station. Press and hold the SET button on the front panel
just after pressing and holding the PWR button. By doing this, the Belt Pack will also be in „pairing processing mode‟ and
the message, “Pairing…” will shortly appears on the Belt Pack display and then you can release both buttons.\
NOTE 1: When executing the paring processing with a Belt Pack, after pressing and holding the PWR button, quickly press
and hold the SET button otherwise, the Belt Pack power may be turned off.
NOTE 2: While the pairing process, all communications will be halted temporarily and recovered upon completing the pairing.
NOTE 3: When you pair up each Belt Pack with the Mobile Station for the first time, each ID number of the Belt Pack is
generated sequentially.
IF PAIRING COMPLETED PROPERLY:
The display of the Belt Pack shows a Belt Pack Label with an ID number that is sequentially generated from “1” to “128”. If the
paring is completed successfully “Paring…” message will be changed to “Paring Completed” within 20 seconds as shown from
Figure 3-3. And the LED adjacent to the TALK button of the Belt Pack is changed to green.
Move to QUIT and press SET button to return to the BELTPACK menu. Repeat the paring processing for each Belt Pack.
IF PARING IS FAILED:
After the message “Pairing...” appears on the Belt Pack display, up to 20 seconds will be taken until the message, “Pairing
Failed” appears on the Belt Pack display. Try to process the paring again. If the paring is failed again, try again after rebooting
of the Belt Pack. If these processes do still not work, please contact your dealer or manufacturer for the further supports.
Pairing …
Pair- ID:000
Pairing Failed
Pairing …
BPK01 ID:001
Pairing Completed
Power Off/On
Figure 3-3: Pairing completed status
Figure 3-4: Pairing failed status

ⓒ2017 LaON Technology Co., Ltd. All rights reserved. 19
BATCHG125 BATTERY CHARGER SETUP
The BATCHG125 is a seven-bay charger for charging the Belt packs, BAT50 and BAT150 Rechargeable Battery Pack. It is able to
charge up to five Belt Packs with the BAT50 Rechargeable Battery Packs are equipped, and two BAT50 Rechargeable Battery
Packs in about 4.5 - 5 hours. Using the Belt Pack/BAT150 dual bay, up to two BAT150 Rechargeable Battery Packs can be charged
instead of the Belt Pack. LEDs show charging status at all times.
See the “BATCHG125 Operating Instructions” for details.
BRK150 MOUNT KIT INSTALLATION
Fasten the enclosed two (2) screws on the bottom of the Mobile Station. And with the screw holes on the Mount Kit, the Mobile
Station can be fixed install on a wall or camera tripod.
Figure 3-5. BRK150 Mount Kit
3
2
1
Screw holes on the wall
Screw hole for a camera tripod
Screw holes to fasten with Mobile Station