Larson Electronics LEDWP-LP-450-TRN-DCM User manual

LEDWP-LP-450-TRN-DCM
Larson Electronics, LLC
Phone: [phone]
Fax: [phone]
www.larsonelectronics.com
1 of 2
45W LED Flood Light
5100 Lumens - 120-277V AC - IP66 Rated
Instruction Manual
Thank you for your purchase of the Larson Electronics LEDWP-LP-450-TRN-DCM LED Flood Light.
Please follow the steps below in order to install, operate and maintain this product.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. THE LEDWP-LP-450-TRN-DCM MUST BE WIRED IN ACCORDANCE WITH NATIONAL
ELECTRICAL CODE ANDALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.
WE STRONGLY ENCOURAGE ONLY ALICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS
PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,
CONSULTAN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.
WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE
INSTALLATION OR PERFORMING ANY MAINTENANCE.
RISK OF FIRE/ELECTRIC SHOCK – DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.
RISK OF PERSONAL INJURY – FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.
RISK OF BURN – ALLOW FIXTURE TO COOL BEFORE SERVICING.
MOUNTING
Follow the guideline below toproperly assemble and install the unit.
The wall packlight includes the LEDlight and trunnion mount.Some models may omit hardware depending
on selected options.
1. Begin by choosing a location toinstall the fixture. This LEDflood light issuitable for outdoor use where the
potential exposure of ultraviolet light, moisture or full water immersion exists. The LEDWP-LP-450-TRN-DCM
operates in extreme temperatures from -40ºC to 45ºC and includes an unbreakable polycarbonate lens that
protects the LEDS against the buildup or intrusion of dust, dirt and humidity.
2. Affix the mount to your chosen surface. There are pre-drilled holes on the trunnion bracket for mounting and
for the cord grip. These can be used anyway suitable for the location. Plan a way for wiring to connect such as
using a separate junction box and utilize the cord grip where necessary. The trunnion mount can be attached to
any flat surface capable of supporting the load and where mount holes can be drilled.
3. Attach lamp. The lamp is attached to the trunnion mount via mount holes on either side of the fixture. A single
bolt on each side secures the lamp to the mount and holds the lamp in desired position.
WIRING
We strongly encourage a licensed electrician install this product, especially in outdoor locations where
weatherproofing may be required. Universal voltage driver permitsoperation at 120V - 277V AC, 50
or 60Hz.
Warning: Check product label for correct input voltage!
Attach supply line wires to the appropriatelight
fixturewires as shown in the diagram 
Secure each pair with a wire nut according to the
diagram. Utilize a junction box or similar device and
take precautionary steps for weatherproofing all
connections if installed in alocation where water may
come in contact with the unit. Ensure the unit is
properly grounded.

LEDWP-LP-450-TRN-DCM
Larson Electronics, LLC
Phone: [phone]
Fax: [phone]
www.larsonelectronics.com
2 of 2
MAINTENANCE
There are no serviceable parts inside the fixture. However, it is good practice to routinely clean and check the
fixture for proper function.
• Disconnect power running to the lamp and be sure the fixture is cool to the touch.
• Use a non-abrasive glass cleaning solution to clean the lens.
Note: It is not necessary to open the fixture and clean or touch the LED’s.
TROUBLESHOOTING
Refer to the guide below or contact the manufacturer if the fixture does not function properly.
Is the correct line voltage being supplied to the fixture?
Is the fixture properly grounded?
Make sure installed power switches, photocells, etc. are functioning properly.
These instructions may not cover all details or variations of this product for your equipment or installation
requirements. Should further information not covered by these instructions be required, please contact Larson
Electronics at 1-800-369-6671 for further assistance.
Please visit LarsonElectronics.com for Warranty and Return information.