Larson Electronics EPL-LED-150W-RT-JB2-X24V-75C-24W07 User manual

EPL-LED-150W-RT-JB2-X24V-75C-24W07
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
1of 5
150 Watt Explosion Proof LED Flood Light
Surface Mount - 21,000L - 75' SOOW EXP Plug - Wiring Hub - Inline
Transformer
Instruction Manual
Thank you for your purchase of the Larson Electronics EPL-LED-150W-RT-JB2-X24V-75C-24W07.
WARNING:
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CRITICAL SAFETY INSTRUCTIONS:
•INSTALLATION SHOULD ONLY BECONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY
RELEVANT LOCAL BUILDING CODES.
•RISK OFFIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL
SYSTEMS. IFNOTQUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.
•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP
OBJECTS. SUITABLE FOR DAMP LOCATIONS.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. THE EPL-LED-150W-RT-JB2-X24V-75C-24W07 MUST BE WIRED IN ACCORDANCE WITH NATIONAL
ELECTRICAL CODE AND ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.
WE STRONGLY ENCOURAGE ONLY A LICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS
PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,
CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.
WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE
INSTALLATION OR PERFORMING ANY MAINTENANCE.
RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.
RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.
RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.
WARNING:
USER SHOULD BE TRAINED IN THE PROPER USE AND MAINTENANCE OF THIS DEVICE. THIS LINE
CORD IS INTENDED TO ALLOW OPERATORS TO EXTEND POWER TO EQUIPMENT WHEN STATIONARY OUTLETS ARE NOT
READILY AVAILABLE.
IMPROPER USE OF THIS CORD, PLUG, AND RECEPTACLE CAN LEAD TO SERIOUS INJURIES OR DEATH TO
PERSONNEL.
PERIODIC INSPECTION OF THE CORD IS NECESSARY.
THE CORD MUST BE ROUTINELY CHECKED FOR CUTS, BREAKS, OR ANY SEVERE ABRASIONS, AND IF ANY ARE FOUND,
THE CORD MUST BE REPLACED BEFORE RESUMING USE.
WARNING
TO AVOIDTHE RISKOF FIRE,EXPLOSION OR ELECTRIC SHOCK, THIS PRODUCT SHOULD BE INSTALLED,
INSPECTEDAND MAINTAINEDBY A QUALIFIED ELECTRICIANONLY, IN ACCORDANCEWITHALL
APPLICABLEELECTRICAL CODES.
TO AVOIDELECTRIC SHOCK:
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•PRODUCT MUST BE CONNECTEDTOA WIRING SYSTEM WITHAN EQUIPMENT-GROUNDING CONDUCTOR.

EPL-LED-150W-RT-JB2-X24V-75C-24W07
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
2 of 5
TO AVOIDEXPLOSION:
•MAKE SURE THE SUPPLYVOLTAGE IS WITHIN THE VOLTAGE RATING.
•ENSURETHE MARKED TRATING IS LESS THAN THE IGNITION TEMPERATURE OF THE HAZARDOUS
ATMOSPHERE.
•DO NOT OPERATE IN AMBIENT TEMPERATURES ABOVETHOSEINDICATED ON THE PRODUCT
NAMEPLATE.
•DO NOT OPERATE IF THE LENS, CORD, SEALS, HOUSING, RECEPTACLES, ETC. IS CRACKED OR DAMAGED.
IFSO, DISCONTINUE USEAND CONTACT MANUFACTURER FOR REPLACEMENT PARTS.
•ALL FASTENERS SHOULDBE PROPERLY SEATED.
WARNING:
USER SHOULD BE TRAINED IN THE PROPER USE AND MAINTENANCE OF THIS DEVICE. IF WIRING OR LAMP REPLACEMENT
INSTRUCTIONS ARE NOT FOLLOWED EXACTLY, THE HANDLAMP MAY NOT BE SUITABLE FOR THE HAZARDOUS LOCATION INVOLVED.
WHEN HANDLAMP IS CONNECTED TO A POWER SOURCE IN HAZARDOUS AREA, PLUG AND MATCHING RECEPTACLE MUST BE SUITABLE
FOR HAZARDOUS LOCATION INVOLVED. WHEN HANDLAMP IS CONNECTED TO POWER SOURCES OUTSIDE OF HAZARDOUS AREA,
STANDARD DUTY PLUGS AND RECEPTACLES MAY BE USED.
STANDARD PLUG AND TRANSFORMER MUST ONLY BE CONNECTED TO A RECEPTACLE LOCATED OUTSIDE THE
HAZARDOUS AREA!
IMPROPER USE OF THIS HANDLAMP, ASSOCIATED PLUG, RECEPTACLE, AND CORD CAN LEAD TO SERIOUS INJURIES OR DEATH TO
PERSONNEL.
PERIODIC INSPECTION OF THE HANDLAMP AND CORD IS NECESSARY.
THE CORD MUST BE ROUTINELY CHECKED FOR CUTS, BREAKS, OR ANY SEVERE ABRASIONS, AND IF ANY ARE FOUND, THE CORD MUST
BE REPLACED BEFORE RESUMING USE OF THE HANDLAMP.
THE GLOBE IS MADE OF TEMPERED GLASS. IF THIS GLASS BECOMES SCRATCHED OR CHIPPED IT SHOULD BE REPLACED IMMEDIATELY.
The EPL-LED-150W-RT-JB2-X24V-75C-24W07 from Larson Electronics is an Explosion Proof LED Flood Light Fixture
that provides operators with a powerful and energy efficient alternative to traditional hazardous location luminaries. LED
technology and compact design makes this lamp an excellent replacement upgrade option for bulky and high
maintenance cost older fixtures. This unit is equipped with a rear access wiring hub and terminal strips. The EPL-
LED-150W-RT-JB2-X24V-75C-24W07 uses 220 V AC input voltage that is stepped down to 24 V DC via an encapsulated
inline transformer to operate the light fixture.
WIRING
We strongly encourage a licensed electrician install this product,in all locations especially in outdoor areas
where weatherproofing may be required. Universal voltage driver permits operation at 220 V AC Input Stepped Down
to 24 V DC.
Warning: Check product label for correct input voltage!
Attach supply line wires to the appropriate light fixture wires as shown
in thediagram 
Secure each pair of wires according to the diagram. Utilize a junction box or
similar device and take precautionary steps for weatherproofing all
connections if installed in a location where water may come in contact with the
unit. Ensure the unit is properly grounded and that wiring is done according to
all local and national electrical/building codes.
Standard Cord Cap
This unit comes pre-wired from factory with the selected cord cap. Take
precautionary steps for weatherproofing all connections if installed in a
location where water may come in contact with the unit. All outdoor
installations and indoor installations near a wet location require the use of a
GFCI device for safety, according to the National Electrical Code® (NEC).
Ensure the unit is properly grounded.

EPL-LED-150W-RT-JB2-X24V-75C-24W07
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
3of 5
See Images Below as a Reference
BRACKETS A
BRACKET B
BRACKETS A
BRACKET B
MOUNTING
This fixture offers an adjustable surface mounting system that allows this fixture to be mounted to any flat surface
including walls and ceilings. A single ½-13 bolt isused to mount the fixture to the surface.
1.1. Using bolts, washers and nuts provided, attach brackets “A” toboth sides of
bracket “B”.
2.2. The LED fixture has 9 holes for a versatile mount option. Select the holes that you would like to use.
3.3. Brackets “A” will then be bolted to the LED fixture with the remaining bolts and washers.
4.4. The fixture is now ready for installation.

EPL-LED-150W-RT-JB2-X24V-75C-24W07
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
4of 5
WIRING (see attached wiring diagram)
This unit comes preconfigured with selected voltage, beamangle,and color temp.Once mounted, wire cord to correct
voltage listed on nameplate.
This explosion proof flood light is equipped with 75 feet of 12/3 chemical and abrasion resistant SOOW cord between the
light fixture and the encapsulated inline transformer. There is an additional 5 feet of 16/3 SOOW cord extending from the
transformer that is fitted with a waterproof 24W07 non-NEMA twist lock cord cap.
WARNING: CHECK NAMEPLATE
FOR PROPER VOLTAGE. DAMAGE
FROM IMPROPER VOLTAGE WILL
VOID WARRANTY.
VOLTAGE
This light uses 220 V AC input voltage that is stepped down to the 24 V DC voltage required to operate the light ficture.
The voltage is stepped down via an encapsulated inline transformer.
MAINTENANCE
Caution: To avoidpersonal injury, disconnect power to the light and allow the unit to cool downbeforeperforming
maintenance.
Warning:No user serviceable parts inside of fixture. Riskof electric shock. Removal of the lens will voidthe warranty.
1. Perform visual,mechanical and electrical inspections on a regular basis.We recommend routine checks to be
made on a yearly basis. Frequency of use and environment shoulddetermine this. It is recommendedto follow an
Electrical Preventive Maintenance Program as described in NFPA 70B: Recommendedpractice for Electrical
Equipment.
2. The lens should be cleaned periodically as neededto ensure continued photometric performance. Clean the lens
with a damp, non-abrasive,lint-free cloth. If not sufficient, use mild soapor a liquid cleaner.
3. Inspect the cooling fins on the luminaire to ensure that they are free of any obstructions or contamination (i.e.
excessivedust build-up). Clean with a non-abrasive clothif needed.
4. Do not operate if the lens is cracked or damaged. All fasteners shouldbe properly seated.

EPL-LED-150W-RT-JB2-X24V-75C-24W07
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
5of 5
WARNING: CHECK NAMEPLATE
VOID WARRANTY.
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.
Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of
children when not in use.Inspect for good working condition prior to storage and before re-use.
REPLACEMENT PARTS
The EEPL-LED-150W-RT-JB2-X24V-75C-24W07 is designed to provide years of reliable performance. Should the need
for replacement parts arise, please contact Larson Electronics.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
[e-mail] OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.