Larson Electronics WAL-M-3X48LED-120 User manual

WAL-M-3X48LED-120
144 Watt LED Flood Light - 3x 200lb. Magnets on Aluminum Base
IP67 - 120-277VAC
Instruction Manual
Thank you for your purchase of the Larson Electronics WAL-M-3X48LED-120 aluminum flood light fixture.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. THE WAL-M-3X48LED-120 MUST BE WIRED IN ACCORDANCE WITH NATIONAL ELECTRICAL
CODE AND ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.
WE STRONGLY ENCOURAGE ONLY A LICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS
PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,
CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.
WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE
INSTALLATION OR PERFORMING ANY MAINTENANCE.
RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.
RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.
RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.
•PEOPLE WITH PACEMAKERS SHOULD CONSULT THEIR PHYSICIAN(S) BEFORE USE.
ELECTROMAGNETIC FIELDS IN CLOSE PROXIMITY TO HEART PACEMAKER COULD CAUSE
PACEMAKER INTERFERENCE OR PACEMAKER FAILURE.
•KEEP FINGERS AWAY FROM MAGNET WHEN MOUNTING AS INJURY COULD OCCUR.
The WAL-M-3X48LED-120 LED work light from Larson Electronics is capable of illuminating an area 675 feet in length by
450 feet in width with 8,640 lumens of brilliant illumination. This compact 120 volt work light comes attached to an
aluminum bracket equipped with three 200 lbs. grip magnetic feet that allows operators to easily mount this unit to any
ferrous metallic surface. This light can be mounted overhead, on tank walls etc. and will stay firmly in place. This unit
includes a waterproof step down transformer to operate the low voltage LED light emitters off standard 120V current.
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 1of 2
Magnetic Mounts
Deutsch
Connector
Mounting
Mounting of this fixture is achieved using the three 200lb
grip magnets at the back of the fixture. Simply stick the
fixture in the desired position to any magnetic metallic
surface capable of supporting the load of the fixture.
Clean the surface before mounting, and be sure to keep
fingers clear of the magnets as they could cause injury.
Take care when removing to not slide the fixture,
especially on painted surfaces, as this could cause
scratches or damage.
Power
WARNING: Check product label for correct voltage!
The light emitters are "instant on" and will power on as
soon as they are supplied with proper voltage. Simply
mate the power cord with the built in transformer via the
quick disconnect Deutsch connector, then plug the power
cord into a compatible receptacle outputting the correct
voltage. The 48 Watt LED light emitters produce 8,640
lumens combined and will illuminate a workspace 675` L
X 450` W in size. This versatile work light can be used as
an overhead light, pedestal light, and just about
anywhere a portable and economical, yet powerful
illumination is needed, and a surface for mounting exists.
QUICK DISCONNECT
DEUTSCH CONNECTOR

WAL-M-3X48LED-120
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 2of 2
MAINTENANCE
There are no serviceable parts inside the fixture. However, it is good practice to routinely clean and check the
fixture for proper function.
•Disconnectpower running to the lamp and be sure the fixture iscool to the touch.
•Use a non-abrasive glass cleaning solution to clean the lens.
•Store in a cool, dry place when not in use.
Note: It is not necessary to open the fixture and clean or touch the LED’s.
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.
Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of
children when not in use.Inspect for good working condition prior to storage and before re-use.
REPLACEMENT PARTS
The WAL-M-3X48LED-120 is designed to provide years of reliable performance. Should the need for replacement parts
arise, please contact Larson Electronics.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
SAL[email protected] OR BY PHONE AT 1-877-348-9680 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.