Larson Electronics LEDWP-600E-E2E-10C User manual

LEDWP-600E-E2E-10C
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
1of 2
60 Watt LED Low Profile Wall Pack Light With Glare Shield
Daisy Chain Capable - U Bracket Mount
Thank you for your purchase of the Larson Electronics LEDWP-600E-E2E-10C Wall Pack Light. Please follow
the steps below in order to install, operate and maintain this product.
MOUNTING
The LED wall pack includes the necessary hardware for installing the mounting bracket, cord grip, and glare
shield. Follow the guideline below to properly assemble and install the unit.
The wall pack light includes the LED light, trunnion mount, glare shield, and hardware for installing the center
cord grip. Some models may omit hardware depending on selected options.
Ambient Temperature Range: -25°C to +60°
1. Begin by choosing a location to install the fixture. This LED wall pack is IP68 waterproof, vapor proof,
and built to resist the damaging effects of an outdoor environment. This fixture should not be used in areas
with no ventilation or extreme ambient temperatures.
2. Affix the mount to your chosen surface. There are 3 predrilled holes on the trunnion bracket. 2 for
mounting and 1 for the cord grip. These can be used any way suitable for the location. Plan a way for
wiring to connect such as using a separate junction box and utilize the cord grip where necessary.
3. Attach lamp.The trunnion mount can be attached to the lamp in two locations, the lower area or middle
area on the back of the wall pack. Use the included ( 2 screws ❶) and ( 2 lock washers ❷) for
attaching the mount as shown in the diagram on page 2. The fixture can be placed in any direction.
WIRING
We strongly encourage a licensed electrician install this product, especially in outdoor locations where
weatherproofing may be required. Universal voltage driver permits operation at 100V - 277V AC, 50 or 60Hz.
Warning: Check product label for correct input voltage!
Attach supply line wires to the appropriate light
fixture wires as shown in the diagram

This unit comes pre-wired from factory with the
selected cord cap. Plug into matching receptacle
outputting voltage on nameplate. Take precautionary
steps for weatherproofing all connections if installed in
a location where water may come in contact with the
unit. Ensure the unit is properly grounded.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. THE LEDWP-600E MUST BE WIRED IN ACCORDANCE WITH NATIONAL ELECTRICAL CODE AND
ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.
WE STRONGLY ENCOURAGE ONLY A LICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS
PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,
CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.
RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.
RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.
RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.
WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE
INSTALLATION OR PERFORMING ANY MAINTENANCE.

LEDWP-600E-E2E-10C
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
2of 2
ASSEMBLY
Use the table below for assembling the hardware including the glare shield.
Note: Some hardware shown may not be included depending on final product configuration.
DAISY CHAIN
Daisy chain multiple fixtures by connecting ends. Plug the male cord
cap from next lamp to the female cord cap of first lamp and repeat for
each additional lamp. Plug the first lamp in the daisy chain to a power
outlet to illuminate all attached lamps.
MAINTENANCE
There are no serviceable parts inside the fixture. However, it is good practice to routinely clean and check the
fixture for proper function.
•Disconnect power running to the lamp and be sure the fixture is cool to the touch.
•Use a non-abrasive glass cleaning solution to clean the lens.
Note: It is not necessary to open the fixture and clean or touch the LED’s.
Should further information not covered by these instructions be required, please contact Larson Electronics at
1-800-369-6671 for further assistance.
CORD GRIP
MOUNT SCREW
ASSEMBLED UNIT w/Glare Shield