Larson Electronics GL-30100 User manual

GL-30100
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 1of 2
GL-30100 Handheld Remote Control for Golight Stryker and Radioray Wireless
Remote Control Spotlight
Instruction Manual
Thank you for your purchase of the Larson Electronics GL-30100.
WARNING:
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CRITICAL SAFETY INSTRUCTIONS:
•INSTALLATION SHOULD ONLY BECONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY
RELEVANT LOCAL BUILDING CODES.
•RISK OFFIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL
SYSTEMS. IFNOTQUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.
•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP
OBJECTS. SUITABLE FOR DAMP LOCATIONS.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. THE GL-30100 MUST BE WIRED IN ACCORDANCE WITH NATIONAL ELECTRICAL CODE AND ALL
APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.
WE STRONGLY ENCOURAGE ONLY A LICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS
PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,
CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.
WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE
INSTALLATION OR PERFORMING ANY MAINTENANCE.
RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.
RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.
RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.
Handheld remote control for Golight Stryker wireless remote control spotlights and Golight Radioray wireless remote control
searchlights. While specified for the Golight Stryker series (GL-3XXX), this remote works with the Golight Radioray series, if those
wireless remote control spotlights (GL-7XXX or GL-2XXX) were purchased within the last 3 years, this remote will work with those
spotlights as well.
Golight remote control spotlights are based on radio waves, not infrared (like your garage remote. As such, these remote controls are
effective to 150 feet.
The handheld remote control is weather resistant.
Powered by 2 MN-21 batteries, which are included and last approximately 1 year, the unit has a series of dip switches. The dip
switches enable the user to select one of 65,000 channels to communicate with a specific remote control spotlight.
This handheld remote control features an on/off button, a fast/slow selector and 4 directional buttons. The motorized remote control
spotlight will move in a direction as a long as the button is depressed. Once released, the remote control spotlight will hold that
position.
Low Voltage DC
Connect power to power supply outputting low voltage between 9-42Volts DC.
This variable voltage allows greater versatility without affecting light output. Ensure
deutsch connectors are properly connected (If applicable)

GL-30100
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 2of 2
GOLIGHT REMOTE OPERATION
A. The power button power’s the light on your Golight on/off. The Golight will continue to pan and
tilt with power supplied regardless of this setting.
B. The up, down, left and right arrows on the wireless remote control will move the Golight in the
corresponding direction. The Golight will rotate as long as power is supplied.
C. The tortoise/hare button sets the pan/tilt speed. Press it once for slower precise movement;
press it again for quick movement.
BATTERY INSTALLATION AND REMOVAL FOR TRANSMITTER
•Remove battery cover: For wireless hand-held transmitter, remove Phillips head screw
to remove cover. For wireless dash mount remote, simply remove the exterior rubber
cover.
•With battery compartment now exposed, gently remove old batteries by grabbing the
positive end and lifting up. Insert 2 X GP 23A 12V batteries according to the correct
polarity.

GL-30100
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 2of 2
MAINTENANCE
There are no serviceable parts inside the fixture. However, it is good practice to routinely clean and check the
fixture for proper function.
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.
Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of
children when not in use.Inspect for good working condition prior to storage and before re-use.
REPLACEMENT PARTS
The GL-30100 is designed to provide years of reliable performance. Should the need for replacement parts arise, please
contact Larson Electronics.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
[e-mail] OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.
PROGRAMMABLE REMOTE INSTRUCTIONS
The Golight is controlledwith a programmable remote with 2187 different channels. This feature allowsyou the freedom to change
the channel selection, and the receiver re-learns the new selection. This light has beenpre-programmed at the factoryand is not
necessary to re-program the transmitter, unless you experience outside interference.
NOTICE
•The remotecontrolis a transmitter. The light contains a receiver.
•The lightis always “hot”.The light is constantly listeningfor a transmitter as long as it is connectedto power.
•Thusit is criticalthat you disconnect the power fromthelightyou do not wish to reprogram.
•All lightswithin 200 feetof acontroller (transmitter) mustbe disconnected fromtheir power beforecompleting this
procedure.
1. Golight controllers have a series of dip switches on the back of thecontroller. The dip switches are accessed by removing the
battery cover. By default, all dip switches are set to the zero position. Moving any one dip switch changes the channel for
that transmitter (controller). Once you have changed a dip switch,proceed to step 2.
2. Disconnect the power to the light you wish to control with the transmitter with thenew
dip switch setting.For cigarette plug models, this means pulling the cigarette plugoutof the socket. For hard wired models,
you may need to physically separate the crimped connection. On vehicleinstallations,you might need to pull thefuse for
that connection.
3. Press and hold down theON/OFF button on the transmitter (controller).
4. Continueto hold down theON/OFF button on the transmitter (controller)while
reconnecting the power to the light.Wait 5-8 seconds. Thelight bulb should turn on.
5. Now, that remotecontroller will communicate with thelight only.
NOTE: When youinstall multiple Golights on onevehicle, vessel or other single power source, connect each Golight to a
separate fuse.