Larson Electronics PTB-1-WR User manual

PTB-1-WR
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
1of 6
Spare Remote Controller for PTB-1
Instruction Manual
Thank you for your purchase of the Larson Electronics PTB-1-WR.
WARNING:
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CRITICAL SAFETY INSTRUCTIONS:
•INSTALLATION SHOULD ONLY BECONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY
RELEVANT LOCAL BUILDING CODES.
•RISK OFFIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL
SYSTEMS. IFNOTQUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.
•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP
OBJECTS. SUITABLE FOR DAMP LOCATIONS.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. THE PTB-1-WR MUST BE WIRED IN ACCORDANCE WITH
NATIONAL ELECTRICAL CODE AND ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR
SAFETY.
WE STRONGLY ENCOURAGE ONLY ALICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS
PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,
CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.
WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE
INSTALLATION OR PERFORMING ANY MAINTENANCE.
RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING. RISK
OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOTINSTALLED PROPERLY. RISK
OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.
Wireless remote for the PTB-1; remote control Pan Tilt Base.

PTB-1-WR
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
2of 6
WIRELESS REMOTE TRANSMITTER PROGRAMING PROCESS
Disconnect the cigarette jack (Y-Pin Connector)
Make sure there are NOT any transmitter operations within 3 meters while programming
Plug in the cigarette jack (Y-Pin Connector) and connect power supply
Within five seconds, turn power on and press the transmitter’s upper button and down
button at the same time. The lamp will flash once, which means it accepts the first
transmitter.
If you like to program the second transmitter (one lamp accepts three transmitters at most),
within five seconds, after the first transmitter completed its program process press the second
transmitter’s upper button and down button at the same time. The lamp will flash
twice to accept the second transmitter.
If no action is taken for five seconds, the lamp will leave programming mode.
ATTENTION: If you would like to use the original transmitter, you should program it during the
same programming process with the new ones, or the original transmitter will be unavailable.

PTB-1-WR
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
3of 6
Remote Control
•ON/OFF – Power’s the unit on or off.
•UP DOWNLEFTRIGHT - Moves the pan/tilt base in the corresponding
direction.
LOCK Remote Functionality
Press the LEFT +RIGHT buttons on the
hardwired remote simultaneously or press the
/button on the wireless remote.
A BLUE backlight on the hardwired remote
indicates the remote functionality is LOCKED. A
RED backlight indicates the remote functionality
is UNLOCKED and both the wired and
hardwired remotes will function.

PTB-1-WR
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
4of 6
HANDHELD WIRELESS REMOTE PROGRAMMING PROCESS:
1. Switch off DC power.
2. Make sure there is NO other transmitter operating at the same time.
3. Switch on DC power, within 5 seconds press the remote's up and down button
once at the same time.
4. Searchlight will flash to acknowledge the remote, connection has been made.
5. To program the second remote (up to 4 remotes may be used with the
searchlight, programming a fifth will replace the first), within five seconds, pres
the second remote's up and down button after the first remote is acknowledged
or repeat step 1.

PTB-1-WR
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
5of 6
Command Protocols
No Byte1 Byte2 Byte3 Byte4 Byte5 Byte6 Byte7
1Command FFh Receiver ID 00h 04h DATA1 DATA2 CHECKSUM
Description
2Command FFh Receiver ID 00h 02h DATA1 DATA2 CHECKSUM
Description
3Command FFh Receiver ID 00h 08h DATA1 DATA2 CHECKSUM
Description
4Command FFh Receiver ID 00h 10h DATA1 DATA2 CHECKSUM
Description
5Command FFh Receiver ID 00h 20h 00h 00h CHECKSUM
Description
6Command FFh Receiver ID 00h 40h 00h 00h CHECKSUM
Description
7Command FFh Receiver ID 01h 00h 00h 00h CHECKSUM
Description
8Command FFh Receiver ID 00h 80h 00h 00h CHECKSUM
Description
9Command FFh Receiver ID 00h 00h 00h 00h CHECKSUM
Description
10 Command FFh Receiver ID 00h 03h 00h PRESET ID CHECKSUM
Description
11 Command FFh Receiver ID 00h 05h 00h PRESET ID CHECKSUM
Description
12 Command FFh Receiver ID 00h 07h 00h PRESET ID CHECKSUM
Description
13 Command FFh Receiver ID 00h 0Fh 00h 00h CHECKSUM
Description
14 Command FFh Receiver ID 00h 09h 00h 01~02h CHECKSUM
Description
15 Command FFh Receiver ID 00h 0Bh 00h 01~02h CHECKSUM
Description
Command
PAN LEFT
DATA1:PAN SPEED(00~3Fh),DATA2:TILTSPEED(00~3Fh)
PAN RIGHT
TILT DOWN
DATA1:PAN SPEED(00~3Fh),DATA2:TILTSPEED(00~3Fh)
DATA1:PAN SPEED(00~3Fh),DATA2:TILTSPEED(00~3Fh)
DATA1:PAN SPEED(00~3Fh),DATA2:TILTSPEED(00~3Fh)
TILT UP
AUX OFF
AUX ON
ZOOM TELE
ZOOM WIDE
FOCUS NEAR
SETPRESET
PRESET ID=00~7Fh
FOCUS FAR
P/T/Z/F STOP
GOTO PRESET
PRESET ID=00~7Fh
CLEAR
PRESET PRESETID=00~7Fh
REMOTE
RESET

PTB-1-WR
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
6of 6
MAINTENANCE
There are no serviceable parts inside the fixture. However, it is good practice to routinely clean and check the
fixture for proper function.
•Disconnect power running to the lamp and be sure the fixture is cool to the touch.
•Use a non-abrasive glass cleaning solution to clean the lens.
Note: It is notnecessary toopen the fixture and clean or touch the LED’s.
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.
Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of
children when not in use.Inspect for good working condition prior to storage and before re-use.
REPLACEMENT PARTS
The PTB-1-WR is designed to provide years of reliable performance. Should the need for replacement parts arise, please
contact Larson Electronics.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
[e-mail] OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.