Laser BLU-3DGLSBT User manual

BLU-3DGLSBT QUICK START GUIDE
1
PRODUCT CONNECTIONS AND USE
Powering On, Off and Pairing
Pairing Instruction (Required for each new connection)
From the on position, look through your BLU-3DGLST glasses, then press
and hold the power button until 3D vision engages.
Power On Press and hold the On/Off button until the blue indicator light appears.
Once the unit has powered on, the blue light will disappear after 5
seconds.
Power Off Press and hold the On/Off button until the blue indicator light flashes
three times. The unit will then bepowered off.
3D Mode Switch After successfully pairing your BLU-3DGLST,press the On/Off
switch during viewing to toggle between the following two
modes where preferred: 1) 3D mode, left imagefirst 2)3D mode,
right image first
Note 1: New pairing connections should take no longer than 20-30 seconds to complete.
If you are experiencing difficulty please power down your BLU-3DGLST glasses and
repeat the pairing process.
Note 2: Your BLU-3DGLSBT glasses can only be paired to one 3D TV at a time. The
pairing process needs
to be repeated each time the glasses are used with a different 3D TV.
Note 3:When the battery is low, the blue indicator light will blink continuously and
should be recharged.
During charging the light will change to red then turn off once charging is complete.

BLU-3DGLSBT QUICK START GUIDE
2
Re-charging
Your BLU-3DGLSBT will provide up to 50 hours ofnormal viewing operation from one3
hour charge.
The glasses will automatically power off, where no 3D signal has been received by the
glasses for over 30 seconds
Charge your BLU-3DGLSBT using the supplied micro-USB cable, as shown below:
Note 1: Turn off your glasses while not in use to preserve power and the life of the
battery
Note 2: Your BLU-3DGLSBT glasses may automatically power off to save energy during
charging
Note 3: The battery is not replaceable.
General use and operation
The viewing and signal range depends on the TV’s size and viewing angle.
A typical setup is shown below:

BLU-3DGLSBT QUICK START GUIDE
3
Things to keep in mind while using 3D technology
- Some artificial light sources such as fluorescent lamps operate on similar wave lengths
as your 3D glasses. As result of this interference you may experience some minor
screen flickering. In this case it is best to turn any offending lights off or at least turn
them down to minimise this effect.
- Surrounding 3D emitting and receiving devices such as glasses or TV’s in a
neighbouring room for example or in close proximity, may alsobe a source of
interference.
- If you changethe channel orthe input modewhile watching 3D, your glasses may
enter stand-by mode or the screen may display abnormally.
- If the TV emitter connection between your glasses and yourTV is interrupted such as
changing viewing angle or distance from the TV, your 3D glasses may enter stand-by
mode
- Be sure to stay within the viewing angle and optimum TV viewing distance to enjoy
proper 3D effects.
FAQ
Q. My 3D glasses do not operate.
A1. Focus your3D glasses toward the front of theTV.
A2. Make sure that the distancebetween the TV and your 3D glasses is within 19.68
feet (5m) in a straight line.
A3. Check the 3D function settings of your TV.
Q2. When start up the glasses, working indicator doesn’t work.
A. The battery is drained. Chargeit with the micro USB cable.
Q3. Left-Right Images Reversed.
A. Please confirm whether the images you see is as the same as the original 3D glasses,
if not,press the operation button once.
- By design, active 3D glasses technology operates using repetitive opening and closing of the LCD
apertures or lens. People with sensitivities to flashing lights or any related conditions such as
epilepsy or disposition to seizures are recommended to seek professional medical advice before
viewing any active 3D video technology.
- It is recommended that children be supervised when using 3D products.
- If you are experiencing any adverse effects from watching3D video technology such as light
headedness, dizzinessorinvoluntary muscle movements it is recommended that you immediately
stop and seek further professional medical advice.
For further product information and instruction please visit our product
web page at www.laserco.net or email [e-mail]
Please note: As continual improvements are made to this product, slight operational
differences may occur. For the most up-to-date user manual, please visit our web site.

BLU-3DGLSBT QUICK START GUIDE
4
Warranty Against Defects
Laser Corporation Pty Ltd (“Laser”) warrants your new product to be free from defects in materials
and workmanship for 12 months, from the date of purchase, provided that the product is used in
accordance with accompanying recommendations or instructions where provided. The benefit of
this warranty is in addition to your rights under the Australian ConsumerLaw and to other rights and
remedies of the consumer under a law in relation to the goods or services to which the warranty
relates.
Through a network of retailers and resellers, Laser will provide you with your choice of a refund,
repair or exchange (where possible) for this product if it becomes defective within the warranty
period. This warranty will no longer apply where the defect is a result of alteration, accident,
misuse, abuse, normal wear and tear, neglect or improper storage.
Please retain your receipt as proof of purchase
How to make a product warranty claim:
Step 1: Find your receipt which proves the date of purchase. Where the date of purchase cannot
be verified, your place of purchase or Laser will make an assessment based on the date of
manufacture, the condition of the Laser Product and the type of defect.
Step 2a): Contact your place of purchase. They will assess the nature of the fault and refund or
replace the product as per their store refund or warranty policy.
Step 2b): If your place of purchase cannot be contacted, then you can contact Laser . Customer
Service with details of your defective Laser Product: Phone: [phone]; or Email:
[e-mail] or online www.laserco.net/support/warranty (click on “Consumers (End
Users)”). Our business address is at 1/6-8 Byfield Street, North Ryde, NSW 2113
Step 3: Laser . will issue you with a Return Authorisation (RA) number within 48 hours. When
requested, send us the defective Product and a copy of your receipt. Laser will cover the cost of the
return delivery.
Step 4: Wait for us to contact you. Once we have received your defective Laser Product for
inspection, we will inform you of our assessment of your claim within 7 days. When we contact you,
we will firstly let you know whether you have a valid claim under this Warranty, and if so, we will
inform you whether your defective Laser Product will be replaced or repaired, together with the
number of days you can expect to wait to receive your replaced or repaired Laser Product.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You
are entitled to a replacement or refund for a major failure and compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced
if the goods fail to be of acceptable quality and the failure does not amount to a major failure.