Laser ALC-MIROR-170 User manual

Mirrored Alarm Clock
ALC-MIROR-170
User Manual

WHAT’S IN THE BOX
• Mirror Clock
• Stand
• USB-A to USB-C power cable
• User manual
You may also need:
• USB power adaptor

WHAT’S IN THE BOX
CONTROLS AND PORTS
Alarm on
Snooze button
Wall mounting
USB Output
USB Output
Type-C
Charging Port
USB Output
USB Output
Type-C
Charging Port
Auto Light
Sensing
Mode
Up
Down

OPERATIONS
INSTALL THE STAND
Insert the stand into the two recesses at the
bottom of the clock.
To remove, pull it out gently.

OPERATIONS
OPERATIONS
TURNING ON THE CLOCK
Connect the clock to a USB power adaptor
using the USB-A to USB-C cable.
SET TIME
1. In Time mode, hold down the Mbutton until
the screen starts ashing.
The setup sequence is:
2. Pres the +or –button to adjust 12hr/24hr
clock, hour, and minute digits.
3. Press the Mbutton to switch between
12hr/24hr, hour and minute, and save the
time.
NOTE: If power is disconnected, all settings will
be reset to their default.
continued...

SET ALARM
1. In time mode, press the Mbutton to switch
to alarm mode.
2. Hold down the Mbutton until the time starts
ashing.
The setup sequence is hour →minute →
snooze time:
3. Pres the +or –button to adjust the hour and
minute digits, and snooze time. The default
snooze time is 5 minutes with max at 60
minutes.
4. Press the Mbutton to switch between hour,
minute, and snooze time.
5. When the alarm is activated, the AL symbol
will be displayed on the clock.
6. In Time mode, press the -button to turn on/
o the alarm.
OPERATIONS
continued...

OPERATIONS
SNOOZE FUNCTION
1. The buzzer will sound for 2 minutes. Press the
Snooze button to start the snooze; the AL
symbol will start ashing.
2. Press any button other than the Snooze
button to turn o the alarm or snooze mode.
ADJUST CLOCK BRIGHTNESS
1. Manual Method - In time mode, press the
+button to cycle between Bright, Medium,
and Low brightness modes. Bright mode is
the default setting.
2. Using ambient light sensor - The clock
display will adjust according to the
brightness of the environment when the light
sensor setting is turned on. The display will
be brighter in brighter environments and
dark in dim-lit environments. The setting is
set to O by default. Hold down the +button
to turn on/o automatic light-sensing
function.
continued...
OPERATIONS

SET NIGHT MODE
The clock brightness will be set to Low mode
from 6 PM to 6 AM each night by default. The
default night mode state is O.
NOTE: For the night mode function to work, the
ambient light sensor function must be turned
o.
In Time mode, double press the Mbutton to
enter the night mode.
Press the +or -button to change the state
On/O.
To change the night mode time period, press
and hold the Mbutton when night mode is on.
The setup sequence is:
OPERATIONS
continued...

CHARGE YOUR DEVICES
Connect your devices’ charging cable to the
mirror clock and your phone.
OPERATIONS
continued...
OPERATIONS

CLOCK IS NOT TURNING ON
Make sure the clock is securely connected to
a USB power adaptor and it’s working. You can
check by using another USB-A to USB-C
cable, USB power adaptor and power outlet.
ALARM DOES NOT GO OFF
Make sure you have set the alarm time correctly.
Check if the alarm is turned ON and the alarm
symbol showing.
USB CHARGING IS NOT WORKING
Make sure the USB cable is securely connected
to both the clock and the device that needs
recharging. Try the other USB port. If it still does
not work, use a dierent USB cable.
TROUBLESHOOTING