Laser WLC-3IN1A-098 User manual

Laser 3-in-1 Charger with Alarm Clock
WLC-3IN1A-098
User Manual

WHAT’S IN THE BOX
• 3-in-1 Charger with Alarm Clock
• Charging cable
• User Manual

Fast Charging: Yes
Input: 9V/3A
Output: 9V/1.66A
Wireless Output: 3W/5W/7.5W/10W/15W
Dimensions: 18.7 x 9 x 6.7cm
SPECIFICATIONS

PRODUCT DIAGRAM
Phone Charging
Surface
Watch Stand
Display Indicator
Light
Earbud Charging
Surface
Function Keys
Watch Charging
Output
Power Input

SETTING THE TIME
• When the time interface is displayed
onscreen press and hold the
button to enter time setting mode.
• Tap the button to switch
between the following settings
(in sequence): 12/24-Hour time >
Hours > Minutes > Exit time setting
mode.
• Tap the or buttons to
decrease or increase the values in each
setting.
SETTING THE ALARM
• You can set up to a total of 3 alarms
- AL1, AL2, AL3.

• When the time interface is displayed
onscreen tap the button to enter
alarm setting mode.
• Tap turn alarm on/o.
• Tap the button to switch
between AL1, AL2, AL3.
• Press and hold the button to
enter the time setting mode for the
chosen alarm.
• Tap the button to switch
between Hours > Minutes > Next Alarm.
• Tap the or buttons to
decrease or increase the values in each
setting.
Note: When the alarm activates it will ring for
20 seconds, and then stop. After 10 seconds
it will ring again for 20 seconds. During the
alarm ring you can press any key to interrupt
the process and end the alarm.

DISPLAY BRIGHTNESS
• When the time interface is displayed
onscreen tap the button to enter
the display brightness mode.
• Tap to change between 5 display
brightness modes.
• Tap to exit the display
brightness mode.
0: Display brightness according to time
1 – 4: Increase display brightness.
5: Screen o mode (screen turns o after
5 seconds of inactivity).
BRIGHTNESS SETTING

PHONE & EARBUD
CHARGING
• Place a QI compatible phone or
earbuds case on the centre of the
phone charging surface or earbud
charging surface.
• Fast charging up to 15W is
supported when charging a phone
(not earbuds), provided you are using
the supplied cable and a fast-charging
compatible adapter.

WATCH CHARGING
• Place your watch on the watch
stand.
• Connect the charging cable that
was originally supplied with your watch
to the watch charging output on the
back of the charger, then to your watch.

TIPS FOR SAFE
CHARGING
1. AVOID OVERCHARGING.
Disconnect chargers and devices after the
battery reaches a full charge. Leaving
devices on a charger too long can cause
them to overheat and can reduce battery
life.
2. PICK THE RIGHT CHARGER.
Only use the charger and cable that came
with your device. If no charger was supplied
or using your own charger, always follow the
manufacturer’s recommend charger
requirements. Take special care to match the
correct voltage and amp values your device
requires when picking a charger. Chargers
are designed for specic battery types;
mixing chargers and batteries could result in
unexpected problems.

continued...
TIPS FOR SAFE
CHARGING
3. CHARGE ONLY ON NON-FLAMMABLE
SURFACES.
Devices and chargers can get warm or
sometimes even hot during charging. Make
sure to always place the device and charger
on a non-ammable surface when charging.
Do not place on beds, pillows, paper, or near
any fabric such as curtains or clothing under
any circumstances.
4. AVOID EXTREME ENVIRONMENTS.
Do not recharge your devices in
environments where extreme temperatures
can occur. On particularly hot days do not
charge in places such as the inside of a car,
or an unairconditioned room. If it’s possible,
try and wait till the evening when
temperatures are a bit cooler.

TIPS FOR SAFE
CHARGING
5. MONITOR CHARGING.
Recharge your devices while you are
nearby, preferably in the same room or
another room close by. This way when
there is a defective battery or charger, you
can take it o the power supply
immediately.
WARNINGS:
1. Device is not a toy, keep away from
children.
2. Do not use in environments
exceeding 45°C.
3. Do not use a wall adapter or USB
power source that exceeds the
input rating of the 3-in-1 Charger
(as shown in the specications of
this manual).
continued...

TROUBLESHOOTING
SLOW CHARGING:
• Check there are no obstructions on the
back of your device such as credit cards
or metal objects.
• Put the device on the centre of the
charging surface.
• Phone cases cannot be thicker than
5mm.
• Check you are using an adapter that
does not exceed the input and output
ratings as shown in the specications.
DEVICE NOT CHARGING:
• Power o/on your device and try
charging again.
• Try another charging cable from the
adapter to the 3-IN-1 Charger.
• Check the adapter you are using is
9V/3A.

TROUBLESHOOTING
• Check if your phone supports Qi
Wireless Charging. Only iPhone models 8
and up support Qi Wireless Charging.
• Check you are using an adapter that
does not exceed the input and output
ratings as shown in the specications.
continued...
DEVICE OR CHARGER GETS VERY HOT
DURING CHARGING:
• It is normal for the charging coil to
generate heat during wireless charging. If
you feel the charger is too hot, then take
the device o the charging surface and
wait till it has cooled down.
• Check you are using an adapter that
does not exceed the input and output
ratings as shown in the specications.

Thank you
for your purchase!
Laser Corporation is 100% Australian owned
& operated. To get the most out of your
product please read the user manual
carefully and keep for future use.
For specic information relating to your product
such as Spare Parts, FAQs, Warranty claims, and
more, please scan the following QR code:

Visit our website
www.laserco.com.au
Check us out at
www.youtube.com/lasercoau