LaserPegs ZD 110B User manual

This manual is copyright and cannot be reproduced or used online without Laser
Pegs®Ventures LLC permission. Copyright 2014 © All Rights Reserved US Patent
#7,731,558 Additional Global & Multiple Patents Pending. Laser Pegs®Ventures
LLC. 8304 Consumer Ct Sarasota FL. 34240. Contact: [email protected]om
www.LaserPegs.com
To construct with Laser Pegs®, slide two pieces together to form
a connection. Slide each piece on and o smoothly. (Laser Pegs®
pieces sold separately).
Connecting Pegs
*To avoid short-circuits, keep metal objects and other
unauthorized materials from obstructing the peg holes.
Remove the Phillips head
screw with a 4mm screw
driver.
Requires
3-LR44 Button Cell
Batteries
Screw
Battery Compartment
Cover
Batteries
Power Switch
Battery
Compartment
1. Remove the Phillips head screw.
2. Remove the Battery Compartment Cover.
3. Place three (3) LR44 batteries in the correct
position. (Batteries are to be inserted with the correct
polarity).
4. Replace the Battery Compartment Cover.
5. Replace the Phillips head screw.
6. Slide Power Switch to turn on!
7. Do not mix old and new batteries.
8. Do not mix alkaline, standard (carbon-
zinc), or rechargeable (nickel-cadmium, NiMH) batteries!
9. Exhausted batteries are to be removed
from the power base.
10. Batteries should be recycled or disposed of as per
state and local guidelines.
11. Non-rechargeable batteries are not to be recharged.
12. Rechargeable batteries are only to be recharged under
adult supervision.
13. Rechargeable batteries are to be removed from the
toy before being recharged.
14. The supply terminals are not to be short-circuited.
15. Do NOT throw batteries into re!
Replacing Batteries
Requires 3-LR44 Batteries
Batteries
Included
underside of Zippy Do® Power Base
Power Switch
Slide Power Switch to turn on/o/ash
Slide Power Switch to cycle through dierent light settings.
This Product contains a button battery. If swallowed, it could
cause severe injury or death in just 2 hours.
Seek medical attention immediately.
ZD 110B
MONSTER
TRUCK
AGES 5+
LIGHTED
CONSTRUCTION SET INCLUDES:
• 1 Laser Pegs ®
• 66 Tinted Bricks
•Zippy Do® Power Base
• Instruction Manual
6 Models+
Any creation you can build
Please read this manual before you begin!
Failure to follow this manual’s instructions may
result in damage to the Zippy Do® Power Base
and/or the Zippy Do® pieces. Not adhering to
these instructions will void the manufacturer’s
warranty. The packaging must be kept because
it contains important information.
WARNING:
CHOKING HAZARD-Small parts.
Not for children under 3 yrs.
Do not submerge in water.
EN71, RoHS COMPLIANT
This product complies to
all safety requirements
of ASTM F 963
WARNING: STROBE LIGHTS
MAY CAUSE SEIZURES
DO NOT SUBMERGE IN WATER
x1
Laser Pegs® Parts List
Stackable
x1
Zippy Do® Power Base
x4
x5
x2
x7
x6
x3
x1
x2 x5
x7
x5
x2
x2
Tinted Bricks List
x4
x3
x4
x4
The toy is not to be connected to more than
the recommended number of power supplies
Connects to other
Laser Pegs® pieces
BATTERIES ARE TO BE INSERTED
INTO THE TOY BY AN ADULT ONLY!
ONLY ADULTS SHOULD INSTALL THE BATTERIES
Model
Diculty
Level
MONSTER TRUCK
A
1
STEP
2
STEP
3
STEP
4
STEP
5
STEP
6
STEP
MONSTER TRUCK: Monster Truck shows began in the 80's, when an event promoter saw
eld test footage of a truck driving over cars.
B
Environmental Phenomena
* The unit may malfunction if subjected to radio-frequency interference. It SHOULD revert to
normal operation when the interference stops. If not, it may become necessary to turn the power
o and back on, or remove and reinstall the batteries.
* In the unlikely event of an electrostatic discharge, the unit may malfunction and lose memory,
requiring the user to reset the devise by removing and reinstalling the batteries.
COMBINE
PARTS
FLIP MODEL
OVER
ROTATE
MODEL

Copyright 2014 © All Rights Reserved Global & Multiple Patents Pending.
US Patent #7,731,558
www.LaserPegs.com
7
STEP
8
STEP
9
STEP
10
STEP
18
STEP
11
STEP
14
STEP
12
STEP
16
STEP
15
STEP
13
STEP
17
STEP
A

Copyright 2014 © All Rights Reserved Global & Multiple Patents Pending.
US Patent #7,731,558
www.LaserPegs.com
Laser Pegs® CARES
Questions? Comments?
For additional compliance info:
1-866-432-3735
Contact: Supp[email protected]om
MADE IN CHINA
Slide the switch to Light It Up
MODEL INSTRUCTIONS
All additional model instructions can be
downloaded at www.LaserPegs.com
PRO STOCK PULLER
TROPHY TRUCK
MUD BOG RACER
ROCK CLIMBER
ALL TERRAIN ROVER
Copyright 2014 © All Rights Reserved Global & Multiple Patents Pending.
US Patent #7,731,558
www.LaserPegs.com
19
STEP
20
STEP
21
STEP
22
STEP
23
STEP
24
STEP
25
STEP
26
STEP