Laserworld Swisslas BLUE4500-445 User manual

Swisslas Lasermodule
BLUE4500-445
Manual
Please read carefully before use

DANGER LASER RADIATION!
Danger for eyes and skin. All protective measures for a safe operation of this laser must be applied.
Safety instructions
Make sure to use the correct voltage. The operator has to ensure that laser radiation –also reflected laser
radiation –higher than the maximum permissible level is avoided by technical or organisational measures.
Always ensure that the maximum permissible exposure (MPE) is not exceeded in the area accesible to the
public. In some countries, the operator must notify the insurance and the authorities for industrial safety
before operating a laser. For more information, contact the relevant authorities. Don’t use the module if
housing, or electrical pars are visibly damaged. Do not turn device on and immediately off again frequently.
Always disconnect from mains, when handling or installing the laser. Do not look into the laser beam directly,
especially not with optical instruments. Do not touch the device with wet hands. When the laser diode
becomes dim or broken, please contact your dealer timely.
Laserworld Swisslas BLUE4500-445 Lasermodul
High end Swisslas blue diode laser - used in collimation, scientific experimentation, optics instrument, laser
display and lighting etc.
IMPORTANT
Mounting of SWISSLAS MODULES all Powerranges
Swisslas modules are delivered without heat sink. However, it’s very important to use a heat sink or similar
cooling device. Operating without a heat sink will damage the module in less then one minute.
This heat sink has to be very planar. If it is not, the beams will not be in one line and the module will be
disaligned.
Between the SwissLas Module and your heat please use some steel plain washers with 0.1 to 0.3mm thickness
at the screw. Use the thinnest possible plain washers, but it is important that they are at least as thick as the
non-flatness of your heat sink.
Use thermal compound between your heat sink and the ground-plate of the Laser module. It is very important
to fill the complete gap!
We don't take on any cost for the repairs of any possible failures according to incorrect mounting!
Left image: The heat sink has to be directly beneath the laser module.
Use thermal grease under the TEC element of the laser (don’t overturn the mounting screws, the TEC could
break):
Centre image: Use 3 screws to mount the module (2 on one side, one centred on the other, see image), to
avoid bending of the mounting plate. Use thin washers (0.1mm) to compensate for unevenness of the surface.
Right image: Use a good heat sink with a strong fan. Also use thermal grease between heat sink and mounting
plate. The temperature of the module may not exceed 40°C –if it is exceeded the module will reduce output
power (to ca. 50%) to protect the diodes!

Connectors:
Caution: Do not switch supply voltage and ground –this will damage the driver! You can supply TEC and Diode
from one, or two separate
PSUs –always connect both pins 3 and 5 to the PSU ground connection. When using single ended modulation
(one side connected to ground) connect pin2 to gnd!
Fuse changing
Fuse 2.5A for Diode
Please solder the new fuse
according this picture
Fuse 5A for TEC
If after changing Diode-Fuse the TEC does
not work you have to change this fuse
too.

Technical data / Technische Daten:
Wavelength
Wellenlänge (nm)
445
Power stability
<3%
Min power, mindest Leistung (mW)
4000
Beam height
28mm
Max Power, maximale Leistung
(mW)
4500
Polarization, Polarisation
1:1
Laser class, Laser Klasse
4
Operating temperature (at mount.
Plate), Betriebstemperatur
10 -40°C
Operation Mode, Betriebsmodus
CW
Expected lifetime (hours), mittlere
Lebensdauer (Stunden)
10000
Warm up time, Aufwärmzeit (min)
<2
Modulation
100kHz analogue
Beam divergence, Divergenz
(mrad)
~1
Size (LxWxH), weight (laser
head), Grösse (LxBxH), Gewicht
(Kopf)
150x80x100 mm,
2 kg
Beam diameter (at aperture),
Strahldurchmesser (am Ausgang)
(mm)
4x4
Power supply
12V DC stabilized
3A Diode
9A TEC
Data subject to change without notice. Errors and omissions expected!
Technical drawing:

Abschließende Erklärung
Sowohl Produkt als auch Verpackung sind beim Verlassen der Fabrik einwandfrei.
Der Benutzer des Geräts muss die lokalen Sicherheitsbestimmungen und die Warnhinweise in der
Betriebsanleitung beachten. Schäden, die durch unsachgemäße Handhabung entstehen, unterliegen nicht dem
Einflussbereich der Herstellers und Händlers. Somit wird keine Haftung bzw. Gewährleistung übernommen.
Sollten Änderungen an dieser Bedienungsanleitung vorgenommen werden, können wir Sie darüber nicht in
Kenntnis setzen. Bitte kontaktieren Sie für Fragen Ihren Händler.
Für Service wenden Sie sich bitte an Ihren Händler oder an Laserworld. Verwenden Sie auschliesslich
Laserworld Ersatzteile. Änderungen vorbehalten. Aufgrund der Datenmenge kann keine Gewähr für die
Richtigkeit der Angaben gemacht werden.
Please note
This device has left our premises in absolutely perfect condition. In order to maintain this
condition and to ensure a safe operation, it is absolutely necessary for the user to follow the
safety instructions and warning notes written in this user manual.
Laserworld cannot be made liable for damages caused by incorrect installations and unskilled
operation!
For service please contact your dealer, or see http://en.laserworld.com/en/reclamation-service.html