Lasko 3150G Owner's manual

Rev. C 8/05 82084537 Rev. C 8/05 12084537
1. Read all instructions before using Fan.
2. Make certain that the power source conforms to the electrical
requirements of the Fan.
3. Use this Fan only as described in this manual. Any other use
not recommended by the manufacturer may cause fire,
electrical shock, or injury to persons.
4. To reduce the risk of personal injury and electric shock, the
Fan should not be played with or placed where small
children can reach it.
5. Unplugpowercordbeforeinstalling,servicing,ormovingtheFan.
WARNING: DO NOT DEPEND UPON THE ON-OFF
SWITCH AS THE SOLE MEANS OF DISCONNECTING
POWER WHEN INSTALLING OR SERVICING THE FAN.
ALWAYS UNPLUG THE POWER CORD.
6. This Fan must NOT be used in potentially dangerous locations
suchasflammable,explosive,chemical-ladenorwetatmospheres.
7. DO NOT use Fan in or near a window. Rain may create an
electrical hazard.
8. Completely assemble Fan, according to instructions, before
connecting to power supply.
WARNING:THIS APPLIANCE HAS A POLARIZED PLUG
(ONE BLADE ISWIDER THAN THE OTHER).TO REDUCE
THE RISK OF ELECTRIC SHOCK, THIS PLUG IS
INTENDEDTO FIT IN A POLARIZED OUTLET ONLY ONE
WAY. MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT. IFTHE PLUG DOES NOT FIT FULLY INTO
THE OUTLET, REVERSE THE PLUG. IF IT STILL DOES
NOT FIT, CONTACT A QUALIFIED ELECTRICIAN. DO NOT
ATTEMPTTO DEFEATTHIS SAFETY FEATURE.
WARNING: THIS PLUG IS A SAFETY DEVICE. TO
REDUCE THE RISK OF FIRE, SHOCK, AND PERSONAL
INJURY, DO NOT REMOVE, REPLACE, REPAIR OR
TAMPERWITHTHE ORIGINALLY SUPPLIED PLUG. IFTHE
FAN DOES NOT FUNCTION PROPERLY, IT MAY BE DUE
TOTHE SAFETY DEVICE INCORPORATED INTHIS PLUG.
RETURN TO AN AUTHORIZED SERVICE CENTER OR
CALL 800-233-0268, MONDAY THRU FRIDAY, BETWEEN
8:00AM AND 5:00PM EST.IFTHE PLUGWARNING LABEL
IS MISSING OR DAMAGED, CALL THE TOLL FREE
NUMBER FOR A REPLACEMENT LABEL.
9. Where possible, avoid the use of extension cords. If they
must be used, minimize the risk of overheating by ensuring
that they are UL listed. Never use a single extension cord
to operate more than one Fan.
10.Do not operate any Fan with a damaged cord or plug or after
the Fan malfunctions, has been dropped or damaged in any
manner. Return Fan to authorized service facility for
examination, electrical or mechanical adjustment or repair.
11.Do not insert or allow fingers or foreign objects to enter any
ventilation or exhaust opening as it may cause an electric
shock or fire, or damage the Fan. Do not block or tamper with
the Fan in any manner while it is in operation.
12.Always place the Fan on a stable, flat, level surface when
operating, to avoid the chance of the Fan overturning. Locate
the Power Cord so the Fan or other objects are not resting on
it. DonotrunPower Cord under carpeting. Donotcover Power
Cordwith throw rugs, runners, or the like. Arrange Power Cord
away from room traffic and where it will not be tripped over.
13.This Fan is not intended for use in wet or damp
locations. Never locate a Fan where it may fall into a
bathtub or other water container.
14. Do not use Fan outdoors.
WARNING:REDUCETHE RISK OF FIRE OR ELECTRIC
SHOCK – DO NOT USETHIS FANWITH ANY SOLID STATE
SPEED CONTROL DEVICES.
This Fan is for residential use only.
It is not intended to be used in commercial or industrial settings.
GENERAL SAFETY INFORMATION
When using electrical appliances, basic precautions should always be followed
to reduce the risk of fire, electric shock and injury to persons, including the following:
READ AND SAVE THESE INSTRUCTIONS
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED.
PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH
INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
IMPORTANT INSTRUCTIONS -
OPERATING MANUAL
SAVE THESE INSTRUCTIONS
LASKO PRODUCTS, INC.
1700 Meacham Boulevard
Fort Worth, Texas 76106
ASSEMBLY OF 12" and 16" OSCILLATING FANS
COMMERCIALWARRANTY
This fan is warranted to be free from mechanical and electrical defects for a period of one year from the
date of purchase when used under normal conditions and serviced properly. If this product is determined
to be defective, notify: CUSTOMER SERVICE DEPARTMENT
300 Confederate Drive • Franklin, TN 37065-0569
Phone [phone]

Rev. C 8/05 22084537 Rev. C 8/05 72084537
1. Tilt Fan Head back. Place Plastic Rear Grill on Motor .
(Figure 1)
2.Align tab of Plastic Rear Grill with groove on top of
front Motor cover. (Figure 2)
3. Fully seat Plastic Rear Grill and secure with Plastic Nut
turning CLOCKWISE. (Figure 3)
Figure 4A
Pin
Groove
4. Slide Blade onto motor shaft. (Figure 4) (Align Groove on
blade hub with Pin on motor shaft. Figure 4A )
Figure 4
Blade
Plastic Rear
Grill
Motor
Figure 2
Figure 1
Motor
Plastic Rear
Grill
Fan Head
Figure 3
Plastic Nut
Plastic Rear
Grill
ASSEMBLY NOTES

Rev. C 8/05 62084537 Rev. C 8/05 32084537
5. To secure Blade , screw Spinner onto Shaft
Counter Clockwise until tight on Blade hub.
(Figure 5)
ASSEMBLY
6. Install Ornament into Metal Front Grill. Insert Tabs into
rectanglar
Slots . Snap into place. (Figure 6)
7. With Fan Head tilted back and centered, align Ornament of
Front Grill so it is horizontal. Insert bottom of Front Grill
into Rear Grill . Tabs at the bottom of Rear Grill should be
between two wires of Front Grill . Snap Front Grill into the
Rear Grill beginning at the top and working down both
sides. (Figure 7)
16" Fan Spinner
Figure 5
12" Fan Spinner
Slot
Figure 6
Ornament
Side View
Tab
* Parts 2-4 ordered as a Bagged Assembly
** Parts 14-21 ordered as an Assembly
126
3 (16")
5
4
3 (12")
3
2
1
0
11
12
13
16
14
17
18
19
25
22
26 27
28
29
30
31
32
33
34
35
36
24
23
20
21
15
7
8
9
10
12011212 2011200 Rear Grill
2098061 2098060 Parts Bag*:
22010359 2010359 Plastic Nut (Large)
32010058 2010059 Spinner
42010380L 2010380L Ornament
52096531P 2096529P Front Grill
62010008 2011013 Blade
72010710 2010710 Motor Cover (Front w/Threads)
82010661 2010661 Motor Cover (Rear)
92030062GL 2030066GL Motor
10 2090040 2090040 Screw Motor Cover (1)
11 2010119 2010119 Oscillation Knob
12 2090060 2090060 #7 x .080 PPH Type B Screw (2)
13 7091657 7091657 Threaded Spindle
2010263S 2010263S Neck Assembly **:
14 2010251 2010251 Neck Piece Bearing
15 2010276 2010276 Oscillation Link
16 2090140 2090140 Link Screw (2)
17 2060090 2060090 Elevation Washer
18 2090585 2090585 Elevation Spring
19 2010252S 2010252S Neck Piece
20 2090051 2090051 Neck Screw
21 2060071 2060071 Elevation Range Plate
22 2090033 2090033 Hex Nut
23 2090521 2090521 Elevation Shaft
24 2010110A 2010110A Small Adjustment Knob
25 2010109A 2010109A Large Adjustment Knob
26 2010533 2010533 Stand
27 2009224 2009224 Knob
28 2055087 2055087 Switch
29 2010415 2010415 Rubber Feet (4)
30 2065457 2065458 Stand Ornament
31 2090038 2090038 Screw #8 x 9/16 PPH Type 25
32 2010343 2010343 Bottom Plate (Plastic)
33 2060012 2060012 Bottom Plate (Metal)
34 2091145 2091145 Screw #8 x 1.5 Type A POH
35 2090552 2090552 Wire Nut (Not Shown)
36 02050013WTFPC 02050013WTFPC Power Supply Cord w/Plug
37 2084537 2084537 Instruction Sheet (Not Shown)
REPLACEMENT PARTS LIST
KEY 12" OSC 16" OSC DESCRIPTION
Tab Tab
Snaps Snaps
Ornament
Figure 7

Rev. C 8/05 42084537 Rev. C 8/05 52084537
WARNING: ALWAYS UNPLUG CORD BEFORE
CLEANING OR DISASSEMBLING.
WARNING: DO NOT IMMERSE FAN INWATER!
CLEANING: IMPORTANT!DO NOT immerse electrical parts
inwater! Disassembledgrillsmaybe immersed tobecleaned
with a mild detergent and water. Wipe all other parts with soft
clothmoistened with water and mild detergent only. DRYALL
PARTS COMPLETELY BEFORE REASSEMBLING. After
anymaintenanceor servicing, completely reassemble unit as
describedinthisinstructionmanualbeforereconnectingtothe
power supply.
CAUTION:Do not use gasoline, benzine, thinner, harsh
cleaners, etc. as they will damage the Fan. NEVER use
ALCOHOL OR SOLVENTS.
SERVICING: All other servicing, with the exception of gen-
eraluser maintenance, should be performed byan authorized
service representative.Call1-800-233-0268, Mondaythrough
Friday, between the hours of 8:00 a.m.and 5:00 p.m.EST for
the location of your nearest service center.
LUBRICATION: Motor is permanently lubricated.
MAINTENANCE
OPERATION
OSCILLATION: Push down oscillation knob on motor housing
to make fan head move from side to side. (Figures 8 and 9)
TILTING: This Fan is equipped with a multi-angle Fan Head
forWhole-RoomAirCirculation.Followthe stepsbelow to prop-
erly adjust the "tilt angle" of your Fan.
1. Place one hand just under the Fan Neck.
2. Place your other hand on top of Fan.
3. Gently push or pull the Fan Head until it is in the desired
position.
SPEED: Control fan speed with Speed Knob. (Figure 10)
3 - High Speed
2 - Medium Speed
1 - Low Speed
TEMPLATE - DETACH TEMPLATE AND TURN 90 ° for use...
TM
3
2
1
0
3
2
1
0
MOTOR
HOUSING
1. UNPLUG FAN FROM OUTLET.
2. Remove the Small and Large Adjustment Knobs.
7"
NOTE: BE SURE THAT THE MOUNTING SCREWS ARE INSTALLED IN A WALL STUD FOR MAXIMUM SUPPORT.
NOT SUPPLIED - Two #8x1-1/4" Wood Screws (Must be purchased separately)
STAND
NECK
SMALL
ADJUSTMENT
KNOB
3. Tilt Motor Housing all the way back.
4. Reinstall Small Adjustment Knob and tighten.
5. Reinstall Large Adjustment Knob.
6. Install two #8 x 1 1/4" Wood Screws ( not provided ), using Template below, leaving 1/8" between Screwheads and wall.
7. Mount Fan over Screws using Slotted Holes on Bottom Plate.
NOTE: TO ADJUST HEAD VERTICALLY - Loosen Large Adjustment Knob, set Motor Housing, retighten Knob.
CAUTION: FAN IS UNSTABLE IN THIS POSITION AND CANNOT BE USED AS A TABLE FAN.
LARGE
ADJUSTMENT
KNOB
(For minor adjustments)
BOTTOM
TOP
1/8"
CONVERTING FROM TABLE FAN TO WALL MOUNTED FAN
(Grills and blade removed for clarity)
✄
Down: Oscillate
Up: Stationary
Figure 8 Figure 9
3
2
1
0
Figure 10
Speed
Knob