LAUNDRY SOLUTION SX071000A User manual
LAUNDRY SOLUTION CO., LTD.
Tel : 076-617171 / 089-7246756 / 086-2762580
Website : www.laundryparts.in.th mail : Laundrypart@gmail.com
SX071000A
Washer-extractor Controller
User Manual
Please read the manual carefully before installation and operation！
Software version
X1.LD028A.X07.001-1 V100A1
X1.LL013A.X07.001-1
Rights Reversed, Pirate Punished
【】
。
! "
#
$ "
$
"#%&&
'!"("
)" "
"#
"( #
!"
*
*!"# "
+ "
# #"#
,
,
,
- # "
! ##!
" "
#
! " .
( !
/.#
!/#!"!""#-#
#/*#
#!"
!#
!
!
【】
0 ! # 1 "
2 !" 34
# ( #
0!2" 34
" #(
##
5 ! 34 #
(##
342
#
"#$：#! %
CONTENT
1 GENERAL...............................................................................................................................................1
2 INSTALLATION.......................................................................................................................................2
2.1 Dimension.....................................................................................................................................2
2.1.1 Front panel.........................................................................................................................2
2.1.2 I/O control Board................................................................................................................3
2.2 Electric Connection.......................................................................................................................3
2.3 In erter Parameter Setup.............................................................................................................4
2.3.1 Digital Input........................................................................................................................4
2.32 RS485..................................................................................................................................4
3 BUTTONS INTRODUCTION..................................................................................................................5
4 RUNNING................................................................................................................................................7
4.1 Startup..........................................................................................................................................7
4.2 Manual Running Mode.................................................................................................................7
4.2.1 Start Manual Running........................................................................................................7
4.2.2 Change Time,temperature,le el.........................................................................................7
4.2.3 Stop Machine.....................................................................................................................7
4.3 Automatic Running.......................................................................................................................7
4.3.1 Start Automatic Running....................................................................................................7
4.3.2 Automatic Running.............................................................................................................7
4.3.3 Pause and Continue..........................................................................................................7
4.3.4 Manual Operate..................................................................................................................7
4.3.5 Ad ance Step.....................................................................................................................7
4.3.6 Ending Automatic Running.................................................................................................7
4.3.7 Lock or Unlock...................................................................................................................8
5 PROGRAMMING.....................................................................................................................................9
5.1 Create New Program....................................................................................................................9
5.1.1 Select and enter.................................................................................................................9
5.1.2 Edit......................................................................................................................................9
5.1.3 Exit and sa e......................................................................................................................9
6 PARAMETER........................................................................................................................................10
6.1 Parameter initialization...............................................................................................................10
6.2 Machine parameter setup..........................................................................................................10
6.3 PUNP in erter setup...................................................................................................................15
7 ALARM..................................................................................................................................................17
7.1 Alarm Reset................................................................................................................................17
7.2 Alarm Information and Ob iation...............................................................................................17
7.2.1 Faults of PUNP inverter....................................................................................................18
7.2.2 Alarms of PUNP inverter...................................................................................................20
SX071000A Washer-extractor Controller
1 G N RAL
-.!!！
SX071000A controller is specially designed for the control of the automatic washer extractor. It
features stability and reliability in operation.
SX071000A controller has very convenient human-machine interaction interface with liquid crystal
display to show state of operation of the machine including temperatures at Led display and thus helps
monitoring effect. A reliably sealed, water and dust proof key panel is adopt which contains light touch
keys with over one million times working life.
The controller provides both automatic and manual working modes. Under manual mode, all keys
are properly interlocked to avoid possible misoperation. For automatic mode, 5 different cycles can be
programmed and upon a single touch of the [Start] key, the machine will run automatically to the end of
the selected cycle.
SX071000A controller also provides washer extractor with the following characteristics:
Relays are used as output components to control directly the driving components. This
omission of intermediate relays conduces to less errors and easier maintenance and
trouble shooting.
Timer operation selected under manual mode.
During automatic operation programmed time duration of an on-going step could be
modified manually without stopping the operation.
During operation actual temperatures and set temperatures can be called to display at will.
Maximum extraction time limit were devised to prevent damage to textiles and machine
parts due to excessive extraction.
Deal with unbalance under extracting status intelligently
Ajust the level at your option.
Various parameters integrated in the computer, which can be set up by manuafacturer
before xworks.
1/20
SX071000A Washer-extractor Controller
&&'(
&'')
2/
SX071000A Washer-extractor Controller
&'&*+
,-
. '
.&
. /
.0
. 1
.2 . 3 . 4
&&$,
,
0
.0
/
&
'
)
,
(
56
7 8
+
559'/8
,-
8,&&9* &0:(,
; ;
/
&
'
, ,
$8#;
,
$
$ 6
(
"#,'
+
8
;
34 0
(,'&:
7"(
.4
.3
. 2
8,&&9* &0:(,
,
,
,
8,&&9* &0:(,
5 1< / =2 2< / =2 /</=2
,
7'93
.' 0</=2
3</ =2
.&
./ =< / =2
4</=2
. 1 '9< / =2
NOT ：lectric connection diagram is just for reference.
3/
SX071000A Washer-extractor Controller
&/&/'(
Digital input Li t
The controller parameter “Ba e number of inverter” i 0:
,
&"
,
6
7
&"
7
5
7
8
7
9
7
9:
7
9;
7
9<
))
)):
));
)
)=))
<>
&"
6
The controller parameter “Ba e number of inverter” i 1:
,
&"
,
6
7
&"
7
5
7
8
7
9
7
9:
7
9;
7
9<
))
)):
));
)
)=))
<>
&"
6
Note：When inverter type i punp inverter,SS4 can’t connect with inverter 4.
The controller and inverter parameter
The controller parameter:
Group Item Value
P6:Inverter setup 1:Inverter type Standard inverter
P6:Inverter setup 2:Inverter Control. Relay
P6:Inverter setup 4:Base number of
invert.
0~1
The inverter parameter:
LG-IG5/ LG-IS5：
Item Value（LCD）Value（7 -Segment）
DRV-03：Drive mode FX/RX-1 1
DRV-00：Cmd. freq Need Need
DRV-05~DRV-07：Step freq-1~3 Need Need
I/O-21~I/O-24：Step freq-4~7 Need Need
I/O-12：P1 define Speed-L 0
I/O-13：P1 define Speed-M 1
I/O-14：P1 define Speed-H 2
Delta B：
Item Value
02-01 Cmd 01：Digital Input With STOP
02：Digital Input Without STOP
4/
SX071000A Washer-extractor Controller
04-04~04-07 MI1~MI4 01~04：Speed
05-00~05-14 Step freq Need
2.32 RS485Rs485 mode can’t be used When inverter type is punp inverter.
5/
SX071000A Washer-extractor Controller
/+
Icon Function
[Wa h] button
Press this button to select Standard\Delicate\Heavy washing ways and
stopping washing.
[Cold Water] button
Switch between starting adding cold water1 and stopping adding cold
water1 by pressing this button when the actual level is lower than the
set level.
[Hot water] button
Switch between starting adding hot water and stopping adding hot
water by pressing this button when the actual level is lower than the
setting level.
[Heat] button
Switch between starting heating and stopping heating by pressing
this button when the actual temperature is lower than the set
temperature and the actual level is higher than the value of “Safety
level of heat” parameter.
[Drain] button
Switch between starting drain1 and stopping drain1 by pressing this
button.
[Extract] button
Switch between starting medium extract \Hi extract1\ Hi extract2 \ Hi
extract3\ Hi extract4 and stopping medium extractt by pressing this
button.
6/
SX071000A Washer-extractor Controller
7/
[Supply1] button
Under “manual” mode, the supply1 will work for 30 seconds by
pressing this button and you also can stop the supply1 during
supply1 working by pressing this button.
[Supply2] button
Under “manual” mode, the supply2 will work for 30 seconds by
pressing this button and you also can stop the supply2 during
supply2 working by pressing this button.
[Supply3] button
Under “manual” mode, the supply3 will work for 30 seconds by
pressing this button and you also can stop the supply3 during
supply3 working by pressing this button.
[Level] button
Switch the level among low level, medium level, high level and
calibration level by pressing this button.
[Start] button
Under “Lock” status, press this button to start executing the
selected program
[Stop] button
Under “manual” Mode, press this button to stop current operation;
Under “auto” Mode, press this button to stop current running
program.
[ADD] button
[SUB] button
[UP] button
[DOWN] button
SX071000A Washer-extractor Controller
00'
After power is on, the LCD shows the startup interface for 10 seconds..
0&
0&'
Power on and close the door, it will enter into “Closed status”. Lock the door by pressing [ top]
button. nter into “Manual mode” by pressing any of the following buttons ([Wa h], [Cold Water], [Hot
Water], [Heat], [Drain], [Extract], [Supply1],[Supply2],[Supply3])
0&&,#
Select the setting items between time, temperature or level by pressing [>] [?] button and set the
value by pressing [+] and [-] buttons under manual mode.
Switch the level among low level, medium level, high level and calibration level by pressing [Level]
button.
0&/
Press [Stop] button to stop all the actions running, and return to “Locked status”.
0/8
0/'8
On Program select interface, choose your desired program by pressing [>] and [?] buttons under
“locked” status, and then press [Start] button to start the program.
On automatic running interface, shows the information, time, water level, water temperature and
steps. User also can change time, speed, water level, water temperature manually.
0/&8
When the machine is running, user can pause, continue, or stop the machine, can change time,
speed, water level, water temperature manually, and also can advance to a new step.
On pause status, the controller clue user “Pause run,press <Start>”.
0//,
When the machine is running, user press [Start] button to stop the machine. On pause status all
the actions is stopped, the count down time is also stopped. Press [Start] button to continue running.
Note:
1. Extract tep can not be pau ed.
0/0
When the machine is running, user can change time, speed, water level, water temperature,
actions manually.
0/18
When the machine is running, user can skip to the next or above step by pressing [+] or [-] button.
0/2$8
After complete the last step or press [Stop] button, the controller becomes ending status. The
controller beeps on to clue user, you can stop the buzzer by pressing [Start] button during this beeping
time. User also can lock or unlock the door, and run this program again immediately.
8/
SX071000A Washer-extractor Controller
4.3.7 Lock or UnlockPress [ top] button to lock the door under closed status.
Press [ top] button to unlock the door under locked status.
Note: If the temperature, water level i higher than the afety value, u er can not unlock and
open the door.
9/
SX071000A Washer-extractor Controller
5 Programming There are 5 programs on the controller.
They are pre-set to prog1(standard), prog2(sheets), prog3(rags), prog4(uniform), prog5(towels).
1',"
1''
Select your desired program under “Idle” status, press [?] [@]button, it will enter into “program”
status.
1'&$
Select your desired step by pressing [+] and -] buttons to select your desired step.
Press [Start] button for 3 seconds to delete program completely.
1'/$
If Press the [Stop] button 3seconds under “program” status, LCD displays the information to ask
the user whether save the program . Save the program by pressing [Enter] button. xit without saving
and return to main working interface by pressing [ESC] button.
10/
SX071000A Washer-extractor Controller
6 ParameterNote: All parameter have already been configured for the machine in factory.
Don’t intend to modify any parameter without any pecial requirement. Some modification will
lead to abnormal work.
After power is on, the LCD shows the startup interface. Press [Up] and [Down] button at the same
time during the 10 seconds counting down. nter the password:
In passwords enter page, once a button pressed, a “*” will be displayed on the LCD. [START] is
used to delete and [STOP] is used to exit.
Default factory password is : [COLD WATER], [HOT WATER], [HEAT], [LEVEL], [SUPPLY1],
[SUPPLY2], [SUPPLY3], [DRAIN]. factory password can be used to set all the items of
parameters.
Default user password is: [SUPPLY3], [SUPPLY2], [SUPPLY3], [SUPPLY2], [SUPPLY3],
[SUPPLY2], [SUPPLY3], [SUPPLY2] User password can only be used to set the items with “end
user” level.
After enter the correct password, you can enter into parameters setting interface.
Press [>] or [?] button to select setting item and press [ENTER] button to enter into the selected
item.
Select the sub-item by pressing [>] or [?] button. Press [ADD] or [SUB] button to set the value.
After modification, press [CANCEL] button to exit and then press and hold [CANCEL] button for 3
seconds to reserve the modified value and exit to the idle page.
2'@
On thetop menu Of parameter setup interface, press [>] or [?] button to select “1:Set to defaults”
and press [ENTER] button to enter into this item.
Press [>] or [?] button to select “1: Parameter to defaults” and press [ENTER] button to reset all
the parameters to default value.
Press [>] or [?] button to select “2: Program to defaults” and press [ENTER] button to reset all the
programs to default value.
2&
On the top menu Of parameter setup interface, press [>] or [?] button to select “2:Machine setup”
and press [ENTER] button to enter into this item.
11/
Input password(8 bit):
SX071000A Washer-extractor Controller
7 ( Level
1:
Machine
function
set
1:Machine capacity 20KG 1~200KG Factory
2:Language Chinese Chinese, nglish nd User
3:Temperature units Celsius Celsius,
Fahrenheit nd User
4:Drain while door open Yes No,Yes Open drain valve automatic after open the door for the safety of the
operator. Factory
5:Drain valve status N.C N.C.,N.O. Open: Drain valve is opened while draining.
Close: Drain valve is closed while draining. Factory
6:Count time after heat No No,Yes Wash time without heat time, must reach temperature. nd User
7:Require lubrication 0 0~9999 times
When the times of run reaches this value, it will prompt information of
adding lubrication under door open status. The times of run can be
browsed and be cleared by pressing [ xtract] button for 3 seconds
from startup screen.
Factory
8:Count time after fill Yes No,Yes Wash time without fill time, must reach water level. nd User
2: Input
status
setup
1: Inverter error N.C N.C.,N.O. Open: Inverter error when input signal is invalid.
Close: Inverter error when input signal is valid. Factory
2: Door closed N.C N.C.,N.O. Open: Door closed when input signal is invalid.
Close: Door closed when input signal is valid. Factory
3: xtract shock N.C N.C.,N.O. Open: xtract shock when input signal is invalid.
Close: xtract shock when input signal is valid. Factory
4: mergency stop N.C N.C.,N.O. Open: mergency stop when input signal is invalid.
Close: mergency stop when input signal is valid. Factory
5:Motor overload N.C N.C.,N.O. Open: Motor overload when input signal is invalid.
Close: Motor overload when input signal is valid. Factory
6:Standby
7:Standby
8:Standby
3:Fill and
level
setup
1:Zero level 5cm 0~99cm Set the relative zero level. Factory
2:Low level 20cm 0~Middle Level Set the low level for manual or auto run. nd User
3:Middle level 30cm Low Level~High
Level Set the middle level for manual or auto run. nd User
4:High level 40cm Middle
Level~Overbrim
Level
Set the high level for manual or aut run. nd User
12/
SX071000A Washer-extractor Controller
5:Overbrim level 99cm High
Level~99cm
Set the overbrim level. Drain valve will open when water higher than
the overbrim level. nd User
6:Auto re-fill when low Yes No,Yes Auto re-fill when level is lower than set value. nd User
7:Level diff. of re-fill 4cm 0~99cm Auto re-fill when difference between current and set is larger than
level difference of re-fill. nd User
8:Max time of fill 10 Min 0~255 Min If level is also lower than set value in time, controller will alarm. nd User
9:Safety level of hot 10cm 0~99cm Auto fill cold water when level is lower than safety level while filling hot
water. nd User
10:Hot fill intellective Yes No,Yes Fill hot water or cold water intellective to reach set temperature value. nd User
4:Heat
and
temp.
setup
1:Min water temperature 00~Max
Temperatrue The min value of water set temperature. nd User
2:Max water temperature 90
Min
Temperatrue~99
The max value of water set temperature nd User
3:Temperature of heat 70
Min
Temperatrue~M
ax Temperatrue
The default value of temperature of heat nd User
4:Auto re-heat when low Yes No,Yes Auto re-heat when temperature is lower than set value. nd User
5:Temp. diff. of re-heat 40~99Auto re-heat when difference between current and set is larger than
temperature difference of re-heat. nd User
6:Max time of heat 10 Min 0~255 Min If temperature is also lower than set value in time, controller will alarm. nd User
7:Safety level of heat 10cm 0~100cm Auto fill cold water when level is lower than safety level while heating. nd User
5:Soap
setup
1:Stop filling Yes No,Yes Stop fill cold water while soaping to avoid low water pressure. nd User
2:Safety level 10cm 0~99cm Auto fill water when level is lower than safety level while soaping. nd User
3:Set time of soap 1 20 Sec 0~255 Sec Default set time of soap 1 nd User
4:Set time of soap 2 20 Sec 0~255 Sec Default set time of soap 2 nd User
5:Set time of soap 3 20 Sec 0~255 Sec Default set time of soap 3 nd User
6:
Inverter
setup
1:Inverter type Gerenal Gerenal、 PUNP
Inverter Factory
2:Inverter control. Relay Relay,RS485 Factory
3:Base number of invert. 0 0~1 Base number of inverter while use input signal. Factory
4:Coeff of freq and rev 0.2400 0.0001~0.9999 Coefficient of frequency and rev : Frequency = Rev * Coefficient. Factory
7:Wash
setup
1:Minimum pause fwd/rev 5 Sec 1~255 Sec Min time between forward and reverse to avoid motor overload. Factory
2:Standard wash run time 25 Sec 1~255 Sec Standard wash run time, includes forward and reverse. nd User
3:Stand. wash stop time 5 Sec 1~255 Sec Standard wash stop time, includes forward and reverse. nd User
4:Gentle wash run time 15 Sec 1~255 Sec Gentle wash run time, includes forward and reverse. nd User
5:Gentle wash stop time 5 Sec 1~255 Sec Gentle wash stop time, includes forward and reverse. nd User
6:Heavy wash run time 35 Sec 1~255 Sec Heavy wash run time, includes forward and reverse. nd User
13/
SX071000A Washer-extractor Controller
7:Heavy wash stop time 5 Sec 0~255 Sec Heavy wash stop time, includes forward and reverse.
When “Heavy wash stop time” is set to “0”, it becomes single wash. nd User
8:Wash speed 40 rpm 1~ Max speed of
wash Default speed of norm wash. nd User
9:Gentle speed 50 rpm 1~ Max speed of
wash Default speed of gentle wash. nd User
10:Single speed 60 rpm 1~ Max speed of
wash Default speed of single wash. nd User
11:Max speed of wash 60 rpm 1~100 rpm Max speed of wash. Wash at max speed when the set value is larger
than max speed. Factory
8:
xtract
setup
1:High extract number 1 1~4 High extract number. There are four high extract most Factory
2:Level for balance 20cm 0~99cm Auto fill to level at least before extract to avoid shock. nd User
3:Balance drain level 15cm 0~99cm If the level is higher than level at most after balance drain, controller
will alarm. nd User
4:Forward run time 10 Sec 1~255 Sec Forward run time at beginning of extract. nd User
5:Bala. with water time 60 Sec 1~255 Sec Balance with water time at extract. nd User
6:Bala. drain water time 60 Sec 1~255 Sec Balance drain water time at extract. nd User
7:Mid extract time 60 Sec 1~255 Sec Time of mid extract. nd User
8:High extract 1 time 60 Sec 1~255 Sec Time of high extract 1. nd User
9:High extract 2 time 60 Sec 1~255 Sec Time of high extract 2. nd User
10:High extract 3 time 60 Sec 1~255 Sec Time of high extract 3. nd User
11:Maximum extract time 6 Min 1~255 Min Max time of extract at last phase. nd User
12:Mid extr. delay time 90 Sec 10~255 Sec Delay time from end of mid extract. Factory
13:High extr. delay time 130 Sec 20~255 Sec Delay time from end of high extract. Factory
14:Re-extract times 3 0~20 Re-extract times when shock. If the times is larger than the set value,
controller will alarm. Factory
15:Re-extract wash time 60 Sec 0~255 Sec Wash time before re-extract to unroll the clothes. nd User
16:Balance delay time 30 Sec 0~255 Sec Delay time from end of balance. nd User
17:Forward run speed 40rpm 1~ Balance
speed Forward run speed at beginning of extract. Factory
18:Balance speed 100rpm
Forward Speed~
Mid extract
speed
Balance speed at extract.
nd User
19:Mid extract speed 300rpm Balance
Speed~Max Mid
xtract Speed
Speed of mid extract. nd User
14/
SX071000A Washer-extractor Controller
20:High extract 1 speed 500rpm
Mid xtract
Speed~Hi 2
Speed
Speed of high extract 1.
nd User
21:High extract 2 speed 700rpm Hi 1 Speed~Hi 3
Speed Speed of high extract 2. nd User
22:High extract 3 speed 800rpm Hi 2 Speed~Hi 4
Speed Speed of high extract 3. nd User
23:High extract 4 speed 900rpm Hi 3 Speed~Max
Hi xtract Speed Speed of high extract 4. nd User
24:Max speed of mid extr 400rpm Mid extract
speed ~600 rpm Max speed of mid extract. nd User
25:Max speed of hi extr 999rpm High extract 1
speed ~999 rpm Max speed of high extract. Factory
10:Door
lock
setup
1:Use lock No Yes,No Factory
1:Unlock door temperatu. 500~90Can't unlock the door when temperature is higher than safety
temperature. nd User
2:Unlock door level 5cm 0~99cm Can't unlock the door when level is higher than safety level. nd User
3:Door lock valve status N.C. N.C.,N.O. Open: Door lock valve is opened while locked.
Close: Door lock valve is closed while locked. Factory
15/
Table of contents
Other LAUNDRY SOLUTION Controllers manuals
Popular Controllers manuals by other brands
Eaton
Eaton xComfort CSEZ-01/16 Assembly instructions
Zener
Zener MSC-3 instruction manual
Grundfos
Grundfos DID Series Installation and operating instructions
Unitronics
Unitronics Vision OPLC V130 Replacing
Shinko
Shinko ACD-13A Communication instruction manual
Allied Systems
Allied Systems Freeman 280 manual
Mitsubishi Electric
Mitsubishi Electric FX3UC-4AD installation manual
Mitsubishi Electric
Mitsubishi Electric MR-J5W-G Series user manual
Honeywell
Honeywell Centraline LION Installation & commissioning instructions
ARCA
ARCA MA60 Series Operating and maintenance manual
Smartwares
Smartwares SHS-53000 Installation and user manual
AirCom
AirCom 239K quick start guide
