Lavo Solutions Handy Series User manual

Rev A 71918 Page | 1
HandySeries
HandyFoam & Handy Spray
INSTRUCTION MANUAL

Rev A 71918 Page | 2
TABLE OF CONTENTS
Introducon/Diluon Rates / Contents 2
Product Diagram 3
Product Setup & Use 4
Terms & Condions 5
Introduction
Lavo’s HandyFoam and HandySpray units are simple solutions for spraying foam in a variety of applications. The
HandyFoam and HandySpray come in two tank sizes, 0.4 and 0.7 gallons. The durable and resilient foamers come in a
polypropylene body to resist some of the toughest chemicals.
QTY Description
1Water gun with 3/4 GHT connection
1Top cover with injector
1Dilution tips (bag of 15)
1Suction line with filter.
10.4 or 0.7 GAL tank
1Instruction Manual
Package Contents
Tip Color Ratio
Grey 1:10
Black 1:12
Beige 1:14
Red 1:16
White 1:18
Blue 1:21
Tan 1:23
Green 1:33
Orange 1:40
Brown 1:45
Yellow 1:57
Aqua 1:71
Purple 1:100
Pink 1:250
Clear /
Dilution Rates
**Rates provided are tested at the
viscosity of water with a dynamic
pressure of 36PSI.

Rev A 71918 Page | 3
Product Diagram
Number Description
1Water gun with 3/4 GHT connection
2Top cover with injector
3Dilution tips (bag of 15)
4Suction line with filter.
50.4 or 0.7 GAL tank
6Water inlet hose (not included)
15.3”
10.8” For 0.7 Gal Tank
8” For 0.4 Gal Tank 5.6”

Rev A 71918 Page | 4
Product Setup & Use
• DISCONNECT THE HOSE FROM THE HANDYFOAM AFTER EACH USE.
• SHUT OFF THE WATER VALVE AFTER EACH USE.
Troubleshooting
Operating Mode
Wash Mode
1. Connect the hose to the trigger sprayer.
Refill the tank with chemical.
2. Insert the desired metering tip.
3. Insert the suction line.
4. Connect the top cover to the gun using the quick coupler.
5. Apply the foam, activating the valve.
Shut off the trigger.
Disconnect the tank from the gun using the quick coupler.
Rinse Mode
1. Activate the trigger sprayer to rinse with clean water, once it
has been disconnected from the tank.
Disconnect the gun from the system, make sure to clean the
system.
How to use the Quick Coupler
1. Pull back the coupler ring.
2. Introduce the nipple.
3. Release the coupler ring.
Problem Cause Solution
No
chemical
suction.
1. Suction filter clogged. 1. Clean or replace.
2. Tip clogged. 2. Clean or replace.
3. Water pressure not sufficient. 3. Minimum = 26 PSI
4. Top cover eductor clogged with
calcium.
4. Clean (using descale chemical) or replace the top
cover.
Foam not
sufficient.
1. Water pressure not sufficient. 1. Minimum = 26 PSI
2. Suction filter or tip clogged. 2. Clean or replace.

Rev A 71918 Page | 5
Terms & ConditionsTerms & Conditions
Company warrants its Goods to be free from material defects in material and workmanship for a period of one year ex-
cept: i. when Goods have been modified following delivery and/or subject to improper handling, storage, installation, op-
eration, or maintenance unless those modifications have been authorized in writing by Seller. ii. when an item is pur-
chased by Company as a component part of the Goods, except to the extent to which such item or items are covered by
the warranty, if any, of the original manufacturer. iii. when an item which is a component part of the product has been
furnished by Buyer. iv. no warranty of a component part shall extend beyond the warranty period of the device in which
such component part is incorporated. b. There is no implied warranty of merchantability or of fitness for particular pur-
pose and there are no warranties of any nature except as set forth in paragraph 3 herein. Any claim by Buyer made pur-
suant to Company’s warranty must be made in writing. Company shall have the right to inspect the Goods claimed to be
defective and shall have the right to determine the cause of such alleged defect. All Goods replaced or repaired by Com-
pany under its warranty shall be replaced or repaired F.O.B. Company’s facility. Buyer must notify Company, in writing,
within fifteen (15) days from receipt of Goods of any obvious defect in the product, or shortages, or Company shall have
no obligation to correct such defect. Company shall have the option of re-inspection at Buyer’s plant or its own before
allowing or disallowing Buyer’s claim. Defects that do not impair service shall not be a cause for rejection or recovery
under any warranty. Buyer assumes full responsibility for the use and application of the product. Buyer accepts Compa-
ny’s design and material selection and specifications in placing this order unless other specifications are agreed to in
writing by both parties prior to the manufacture of Goods by Company. Statements and data relating to Products on
Seller’s literature and website are not intended to define the performance of the product in actual usage or in com-
bination with other equipment or processes. These statements should not be used by Customer solely as an indication
of performance or suitability for specific applications or uses.
THE ABOVE WARRANTIES ARE THE SOLE AND EXCLUSIVE WARRANTIES MADE BY SELLER WITH RESPECT
TO ALL PRODUCTS AND SERVICES.
Components and spare parts such as O-rings, squeeze tubes, roller blocks and other plastic components are consid-
ered to be wear parts and are not warranted. Seller shall have no warranty or liability for product that was damaged dur-
ing shipment, product that is not being used in its recommended use, product that is not operated in accordance with the
operating manual and procedures, product that was not properly installed, product used in a manner that is inconsistent
with its designed purpose, product that is subject to a power surge or similar event, products that fail due to usage of a
non Lavo Solutions replacement or spare part or product that was not maintained in accordance with recommended
maintenance programs.
For full terms and conditions visit:
http://lavosolutions.com/LAVO-T&C-02-2018.pdf
Lavo Solutions, LLC
Worldwide Headquarters
23192 Verdugo, Suite #D
Laguna Hills, CA 92653
O: 949-377-1250
W: www.lavosolutions.com
This manual suits for next models
2
Table of contents
Other Lavo Solutions Paint Sprayer manuals