Lawmate PV-500EVO2 User manual

Lawmate PV-500EVO2 User Manual
Last Modified on 12/23/2015 9:03 pm EST
PV-500 EVO User's Guide
Law Enforcement Products Manufacturer
Law Mate
TABLE OF CONTENT
CHAPTER 01 OVERVIEW
02 FUNCTION MODES
03 BASIC OPERATION
04 INTRODUCTION OF ALL SETTING FUNCTIONS
05 VIDEO PLAYBACK
6 VIDEO EDITING

07 PHOTO BROWSING
08 PHOTO EDITING MODE
09 SUPPORTED IMAGE FILE FORMAT
10 RECORD
11 REMOTE CONTROLLER
12 SUPPORTED VIDEO FILE FORMAT
13 SPECIFICATIONS
14 IMPORTANT
15 NOTE
Overview
PV-500EVO Main Device

Remote

Accessories
Optional

Function Modes
Basic operation
Turn on/ off of PV-500 EVO player
To Do this
Turn On Press the Power On/ Off button about 1 sec. on PV-1000, to
turn on the power and the greeting screen will appear.

Turn Off Press the Power On/Off button about 1sec. button on
PV-1000 or press the Power button on the remote control to
turn off PV-1000.
Using the touch screen
Tap any application to get started or tap an item in the list to choose it.
Tap icon to return last page or return back to main menu.
Tap icon or to move next page’s menu. Tap icon for function setting.
Adjust Volume
While playing Video, Tap icon / or the one in the remote controller to adjust
volume.
Volume varies in 10 steps.
Volume status will be displayed on the left–down side of screen.
Record button
Start Recording Push the REC button on the PV-500EVO or the one on the
remote controller to start recording.
Stop Recording: Press STOP button or the one on the remote controller to stop
recording, and the screen will return to stand-by mode of Preview to prepare for
recording.

Link with other equipments

External Video Source Recording– Cam in
Plug an external camera into Cam-in , it enable recording.
External Video Source Recording – Digital Cam in
Output to TV Screen:
Plug an RCA cable in AV-out to have the image output to the TV.
Precaution: Check “Setup” Menu, the setting of “Display” must be set from “LCD”
into “TV” enable image output.
Connect to wire controller:
Connect to PC:

Connect the two ends of A/B type of USB cable to PV-1000 and PC.1.
2 An indication for “USB Mode” appears on the screen for 5 seconds after the link is2.
properly installed.
Charging:
When the power goes down, power LED indictor blinks (green) and the meter with no
bars displays on the bottom right corner of the screen, which indicates that the power
of the host exhausts; please recharge it immediately. connect the main device with the
power supply and then plug the power supply into the electrical outlet. The LED light
will be on Orange.
Precaution: The LED light will be turned off after finishing charging; to keep long life-
span of the battery, the power supply should be unplugged after finishing charging; Please
charge the battery last for 12 hours before 1st time to use
Introduction to all Setting Functions
01. Preview >
Tap SETTINGS on the screen to the page1 of setting functions then Tap Preview to start
setting each function as below.

Resolution (352*288 /640*480/720*576/1024*768/1280*720/1280*960)
Quality (Good/Normal/Low)
Frame Rate( 1 / 5/ 15 /20/25)
Audio (Enable/Disable)
Frame Counter Stamp (On/Off)
Timestamp (On/Off)
Device ID Stamp (On/Off)
Display (LCD/TV/Both)
Microphone sensitivity
Over-write
Notice: For TV output, it is needed to select Display to TV or Both.
02. Pre-event >
Tap SETTINGS on the screen to the page1 of setting functions then Tap Pre-event to start
setting each function as below.

Resolution (352*288 /640*480/720*576/1024*768/1280*720/1280*960)
Quality (Good/Normal/Low)
Frame Rate ( 1 / 5/ 15 /20/25)
Audio (Enable/ Unable)
Frame Counter Stamp (On/Off)
Timestamp (On/Off)
Device ID Stamp (ON/Off)
Display (LCD/TV/BOTH)
Pre-Record Time (30 sec，15 sec)
Microphone sensitivity
Over-write (Disable/Enable)
03. Motion detection >
Tap SETTINGS on the screen to the page1 of setting functions then Tap Motion detection to
start setting each function as below.

Resolution (352*288 /640*480/720*576/1024*768/1280*720/1280*960)
Quality (Good/Normal/Low)
Frame Rate ( 1 / 5/ 15 /20/25)
Audio (Enable/ Unable)
Frame Counter Stamp (On/Off)
Timestamp (On/Off)
Device ID Stamp (ON/Off)
Display (LCD/TV/BOTH)
Motion detection level (LOW/Medium/High)
Motion Detect Record time (30sec/1min/3min/5min/10min)
Motion Detect Zone
Microphone sensitivity
Over-write (Disable/Enable)
04. Date/time setting > Set Date and Time
Tap SETTINGS on the screen to the page1 of setting functions then Tap Date and time to
start setting the number. Tap or to the next page menu.

05. Date/time /format >
Tap SETTINGS on the screen to the page1 of setting functions then tap Date Format to
select.
06. Language > Choose the language for Operating interface
Tap Language on the page2 of setting functions; tap or move next page menu.
07. Recording Mode > set up the screen to be automatically returned
to which recording mode. Tap Pre set recording mode on the page2 of
setting functions then select the one you wish
08. Resume to pre-set duration >
Tap Resume to Pre-set Duration on the page2 of setting functions to select.
09. Timer recording > set up the timing to recording mode
Tap the application of Timer recording on the page 2 of setting functions to select one blank

column in order to reset the timer. Once timer setting is set, the screen will appear
reserving time as below.
Notice: it is needed to set the setting as “ ON” to book the reserved recording
successfully; the reservation will be executed only when the device is in Power on state.
10. Back light out duration >
Setting to turn off the backlight during the device is not used.
11. Storage option >
PV500 device accepts SD card only.
12. Storage information > show the size and the free space of the
storage.
13. Storage capacity > how the icon on the device; SD card needs to be
inserted to slot then will be displayed in the left-bottom side of
screen . Tape to the last page
14. Format memory > allow to format SD

15. TV-out setting >
16. TV-output adjustment >
17. Display > Output TV Display setting
18. Video playback >
19. Video thumbnail > Setting if enable to preview image when reading
video files
20.Image thumbnail >setting if enable to preview when reading photo
files
21. Slide show > setting if enable slideshow

22. Slideshow duration > setting the section time during slideshow
playing
23. Firmware upgrade > Insert the SD card which contains updated
software into the device and press enter button, after the system is
updated, it will reboot automatically; if the message “Update Error” is
shown, it means that there are errors during updating, it might be that
the software is incomplete or the memory card has some problem,
please use other memory card, or reboot the device after inserting the
memory card.
24. Restore factory setting > choose if you would restore factory
setting, Tap ok/Cancel.
25. Power on password > lock or not to lock when turning on
PV-500EVO; if set” On”, it requires password to enter main menu of
PV-500EVO player.

26. Set power on password > Tap your chosen 6 characters and then
confirm these characters once more, after setting Tap Enter to
complete the setting.
27. USB connect password > setting if locked when reading data
through USB
28. Set USB connect password >
Tap your chosen six-character on the screen and then confirm these characters once more,
after setting tap Enter to complete the setting.
29. Create log file >

30. View log > view all log record for power on/off, USB plug-in/out and
record and playback.
31. Save all log file >
Tape it to save all logs
32. Device information > show information about
33. LED > Setting LED panel to be off/on
34. Continuous shot Max > setting the max. times for the continuous
shot
35. Digital CMOS low light mode > Enable or disable for recording in
30fps.

36. Digital CMOS Anti-Flicker >
37. Digital CMOS Calibration >
38. Vibration Settings > setting if use Vibration on the device when
turn on/off or start/stop the recording.
Video Playback
Operations in Main Menu
Tap VIDEO on the Main Menu to open the newest files .
Choose the files to play video as below.

Tap button to open files listed in date; choose desired video file to play. Tap
button again to enter the upper level of My Record.
Fast Playback
Double Speed Playback:
Tap during normal playback, the video file will be played with a speed two times
quicker; press to return to the normal playback speed.
4 Times Speed Playback:
Tap twice during normal playback, the video file will be played with a speed four
times quicker; press to return to the normal playback speed.
8 times Speed Playback:
Tap three times during normal playback, the video file will be played with a speed
eight times quicker; Tap to return to the normal playback speed.