LawnMaster BL705 User manual

8 Amp Electric Blower BL705
3084514
Read all safety rules and instructions carefully before operating this tool.
Distributed By Cleva North America, Inc. 601 Regent Park Court Greenville, SC 29607 (866)-384-8432
Lisez attentivement toutes les règles de sécurité ainsi que les instructions avant de faire fonctionner cet outil.
Distribué par Cleva North America, Inc. 601 Regent Park Court Greenville, SC 29607 (866)-384-8432
Lea todas las reglas e instrucciones de seguridad cuidadosamente antes de utilizar esta herramienta.
Distribuido por Cleva North America, Inc. 601 Regent Park Court Greenville, SC 29607 (866)-384-8432
LawnMaster_BL705_V1
EN p. 2
Souffleuse électrique 8 Amp BL705
FR p. 18
Sopladora eléctrica de 8 amperes BL705
ES p. 35
Operators Manual / Manuel d'utilisation / Manual de uso

Parts List
3-4
Specific Safety Rules 5
Symbols 6
Electrical Information 7-8
9
Assembly
Operation 11-13
10-11
Maintenance 14
14
15
CONTENTS
Important Safety Instructions
Features
Troubleshooting
Warranty
16
17
Exploded View
2
8 AMP BLOWER
Voltage
Amp
Max Air Speed
Max Air Volume
Weight
PRODUCT SPECIFICATIONS
4 lbs.( 1.8kg )
160 CFM
160 MPH
8 A
120 V ~ 60Hz

READ THESE INSTRUCTIONS BEFORE USING THIS BLOWER
READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all
instructions listed below may result in electric shock, fire, and/or serious
personal injury.
WARNING:
IMPORTANT SAFETY INSTRUCTIONS
 Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.
To reduce the risk of electric shock, this tool has a polarized plug ( one blade is wider than the
other ) and will require the use of a polarized extension cord. The plug will fit into a polarized
extension cord only one way. If the plug does not fit fully into the extension cord, reverse the
plug. If the plug still does not fit, obtain a correct polarized extension cord. A polarized extension
cord will require the use of a polarized wall outlet. This plug will fit into the polarized wall outlet
only one way. If the plug does not fit fully into the wall outlet, reverse the plug. If the plug still
does not fi t, contact a qualified electrician to install the proper wall outlet. Do not change the
equipment plug, extension cord receptacle, or extension cord plug in any way.
 Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerators.
There is an increased risk of electric shock if your body is grounded.
 Don’t expose power tools to rain or wet conditions. Water entering a power tool will increase
the risk of electric shock.
 Do not handle plug or tool with wet hands.
 Use outdoor extension cords marked W-A, W, SW-A, SOW-A, STW-A, STOW-A, SJW-A,
SJTW-A, or SJTOW-A. These cords are rated for outdoor use and reduce the risk of electric
shock.
 Never allow children to operate the equipment. Never allow adults to operate the equipment
without proper instruction.
 Wear eye protection with side shields which is marked to comply with ANSI Z87.1 as well as
hearing protection when operating this product.
 Always use face or dust mask if operation is dusty.
 Use extra care when cleaning on stairs.
 Do not leave appliance plugged in. Unplug from outlet when not in use and before servicing.
 Do not expose to rain, store indoors.
 Use only as described in this manual. Use only manufacturer’s recommended attachments.
 Keep hair, loose clothing, fingers and all body parts away from openings and moving parts.
 Wear heavy long pants, long sleeves, boots, and gloves. Avoid loose garments or jewelry that
could get caught in moving parts of the machine or its motor.
 Do not force tool. Use the correct tool for your application. The correct tool will do the job
better and safer at the rate for which it is designed.
 Do not operate the equipment while barefoot or when wearing sandals or similar lightweight
footwear. Wear protective footwear that will protect your feet and improve your footing on
slippery surfaces.
3

 Do not use on steps, a ladder, roof top, tree, or other unstable support. Stable footing on a
solid surface enables better control of the blower in unexpected situations.
 Secure long hair so it is above shoulder level to prevent entanglement in any moving parts.
 Keep firm footing and balance. Do not overreach. Overreaching can result in loss of balance.
 Turn off all controls before unplugging.
 Do not allow to be used as a toy. Close attention is necessary when used by or near children.
 Avoid accidental starting. Be sure the power switch is not on before plugging in. Turn off
power switch before unplugging.
 Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with the
switch is dangerous and must be repaired.
 Do not use with damaged plug. If tool is not working as it should or has been dropped,
damaged, left outdoors, or dropped into water, return it to an authorized service center.
 Do not leave the tool when plugged in. Unplug from the power outlet when not in use, before
servicing, and before storing the tool. Such preventative safety measures reduce the risk of
starting the tool accidentally.
 Keep all bystanders, children, and pets at least 50 ft. away.
 Do not operate this unit when you are tired, ill, upset or under the influence of alcohol, drugs,
or medication.
 Do not operate in poor lighting.
 Keep all parts of your body away from any moving parts and all hot surfaces of the unit.
 Do not put any object into openings. Do not use with any opening blocked; keep openings
free of dust, lint, hair, and anything that may reduce air flow.
 Check the work area before each use. Remove all objects such as rocks, broken glass, nails,
wire, or string which can be thrown or become entangled in the machine.
 Never use blower near fires, fireplaces, hot ashes, barbecue pits, etc., which may cause fire to
spread.
 Do not pull or carry by cord, use cord as a handle, close a door on a cord, or pull cord around
sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.
 Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
 Do not handle plug or appliance with wet hands.
 Use only identical manufacturer’s replacement parts and accessories. Use of any other parts
may create a hazard or cause product damage.
 In a double insulated appliance, two systems of insulation are provided instead of grounding.
No grounding means is provided on a double insulated appliance, nor should a means for
grounding be added to the appliance. Servicing a double insulated appliance requires extreme
care and knowledge of the system and should be done only by qualified service personnel.
Replacement parts for a double insulated appliance must be identical to the parts they replace.
 For household use only.
IMPORTANT SAFETY INSTRUCTIONS
4

Safety Alert
V
A
Hz
W
min
MEANING
DANGER:
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL SIGNAL
WARNING
CAUTION:
CAUTION:
Indicates an imminently hazardous situation, which, if not avoided, will result
in death or serious injury.
Indicates a potentially hazardous situation, which, if not avoided, could result
in death or serious injury.
Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.
(Without Safety Alert Symbol) Indicates a situation that may result in property
damage.
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the product better and safer.
SYMBOL NAME DESIGNATION/EXPLANATION
Indicates a potential personal injury hazard.
Read The Operator’s Manual To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Eye and Hearing Protection Always wear eye protection with side shields marked to comply
with ANSI Z87.1, along with hearing protection.
Wet Conditions Alert Do not expose to rain or use in damp locations.
Keep Bystanders Away Keep all bystanders at least 50 ft. away.
Long Hair Failure to keep long hair away from the air inlet could result in
personal injury.
Blower Tubes Do not operate without tubes in place.
Loose Clothing Failure to keep loose clothing from being drawn into air intake
could result in personal injury.
Volts Voltage
Amperes Current
Hertz Frequency (cycles per second)
Watt Power
Minutes Time
Alternating Current Type of current
Direct Current Type or a characteristic of current
Class II Construction Double-insulated construction
SYMBOLS
6

DOUBLE INSULATION
Double insulation is a concept in safety in electric power tools, which eliminates the need for the
usual threewire grounded power cord. All exposed metal parts are isolated from the internal metal
motor components with protecting insulation. Double insulated tools do not need to be grounded.
NOTE:
Servicing of a product with double insulation requires extreme care and knowledge
of the system and should be performed only by a qualified service technician. For service,
we suggest you return the tool to your nearest authorized service center for repair. Always
demand that original factory replacement parts be used when servicing.
ELECTRICAL CONNECTION
This product has a precision-built electric motor. It should be connected to a power supply that
is 120 volts, AC only (normal household current), 60 Hz. Do not operate this product on direct
current (DC). A substantial voltage drop will cause a loss of power and the motor will overheat. If
your product does not operate when plugged into an outlet, double-check the power supply.
GFCI
Ground Fault Circuit Interrupter (GFCI) protection should be provided on the circuit(s) or outlet(s)
to be used for the product.Receptacles are available having built-in GFCI protection and may be
used for this measure of safety.
GUIDELINES FOR USING EXTENSION CORDS
USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one heavy enough to carry the current your product
will draw. An undersized cord will cause overheating. The table below shows the correct size to
use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge.
The smaller the gauge number, the heavier the cord.
Minimum Gauge for Extension Cords (AWG)
(when using 120 V only)
Ampere Rating Total Length of Cord in Feet (meters)
More Than Not More Than
Not Recommended
25' (7.6 m) 50' (15 m) 100' (30.4 m) 150' (45.7 m)
0 6
6
18 16 16 14
10 18 16 14 12
10 12
12
16 16
16
14
14
12
12
ELECTRICAL INFORMATION
WARNING:
The double insulated system is intended to protect the user from shock resulting from a break in
the tool’s internal insulation. Observe all normal safety precautions to avoid electrical shock.
7

WARNING:
ALTHOUGH THIS TOOL IS DOUBLE INSULATED, THE EXTENSION CORD AND RECEPTACLE
MUST STILL BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM ELECTRICAL
SHOCK.
WARNING:
Check extension cords before each use. If damaged replace immediately.
Never use product with a damaged cord since touching the damaged area could cause electrical
shock resulting in serious injury.
Make sure your extension cord is properly wired and in good electrical condition.Always replace a
damaged extension cord or have it repaired by a qualified person before use.
Keep extension cords away from sharp objects,excessive heat and damp or wet areas.
Use a separate electrical circuit for your tools. This circuit should comprise a wire of at least 12
gauge and should be protected with a 15 A time-delayed fuse. Before connecting the motor to the
power line, make sure the switch is in the OFF position and the electric current is identical to that
stamped on the motor nameplate. Running at a lower voltage will damage the motor.
ELECTRICAL INFORMATION
8

See Figure 1.
KNOW YOUR BLOWER
BLOWER TUBE
The blower tube can be easily installed on the blower without any additional tools.
CORD RETAINER
A convenient cord retainer helps keep the extension cord connection secure during blower operation.
SINGLE-SPEED
This blower is equipped with a single speed motor.
The safe use of this product requires an understanding of the information on the tool and in this
operator’s manual as well as a knowledge of the project you are attempting. Before use of this
product, familiarize yourself with all operating features and safety rules.
A - ON/OFF switch
B - Blower tube
C - Cord retainer
D - Plug
B
A
C
D
Fig. 1
FEATURES
This product has many features for making its use more pleasant and enjoyable. Safety,
performance, and dependability have been given top priority in the design of this product making
it easy to maintain and operate.
9

A - Air outlet
B - Lock button
C - Blower tube
See Figure 2.
Slide blower tube forward until the lock button clicks into the top of the tube.
ASSEMBLING THE BLOWER TUBE
A
C
B
Fig. 2
ASSEMBLY
WARNING:
Do not allow familiarity with products to make you careless. Remember that a careless fraction of
a second is sufficient to inflict serious injury.
WARNING:
Always wear eye protection with side shields marked to comply with ANSI Z87.1, along with hearing
protection. Failure to do so could result in objects being thrown into your eyes, resulting in possible
serious injury.
WARNING:
Do not use any attachments or accessories not recommended by the manufacturer of this product.
The use of attachments or accessories not recommended can result in serious personal injury.
OPERATION
11

See Figure 3-4.
You may use this product for the purposes listed below:
Clearing leaves and other yard debris from your lawn
Keeping decks, patios, garages and driveways free from leaves, pine needles and other debris
Attach the outlet end of an extension cord to the plug on the rear of the blower.
NOTE: Use only an approved outdoor extension cord as described previously in this manual.
Route the extension cord through the side of the loop located on the rear of the blower housing
and place underneath the cord retainer.
To start the blower, place the power switch in the ON position.
To stop the blower, place the power switch in the OFF position.
APPLICATIONS
STARTING/STOPPING THE BLOWER
A - Cord retainer
B - Loop
C - Plug
D - Extension cord
C
D
B
A
ON
OFF
Fig. 3 Fig. 4
OPERATION
12

See Figure 5.
To keep from scattering debris, blow around the outer edges of a debris pile. Never blow directly
into the center of a pile.
To reduce sound levels, limit the number of pieces of equipment used at any one time.
Use rakes and brooms to loosen debris before blowing. In dusty conditions, slightly dampen
surfaces when water is available.
Watch out for children, pets, open windows, or freshly washed cars, and blow debris safely away.
 Hold the blower with the handle in your right hand. (Proper operating position is shown in figure 5.)
Operate power equipment at reasonable hours only — not early in the morning or late at night
when people might be disturbed. Comply with the times listed in local ordinances.
After using blowers or other equipment, CLEAN UP! Dispose of debris properly.
OPERATING THE BLOWER
Fig. 5
OPERATION
13

WARNING:
When servicing, use only identical replacement parts. Use of any other parts may create a hazard
or cause product damage.
WARNING:
Always wear eye protection with side shields marked to comply with ANSI Z87.1, along with
hearing protection. Failure to do so could result in objects being thrown into your eyes, resulting in
possible serious injury.
WARNING:
Before inspecting, cleaning or servicing the machine, unplug the power cord and wait for all moving
parts to stop. Failure to follow these instructions can result in serious personal injury or property damage.
WARNING:
Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in
contact with plastic parts. Chemicals can damage, weaken or destroy plastic, which may result in serious
personal injury.
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various
types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil,
grease, etc.
GENERAL MAINTENANCE
STORAGE (1 MONTH OR LONGER)
Clean all foreign materials from the blower.
Store indoors in a place that is out of reach of children. Keep away from corrosive agents such
as garden chemicals and de-icing salts.
TROUBLESHOOTING
PROBLEM CAUSE REMEDY
Motor fails to start when switch is
turned on.
Power cord is not plugged in or
connection is loose.
Household circuit breaker is tripped.
Plug in the power cord.
Check circuit breaker.
MAINTENANCE
14

EXPLODED VIEW
16

PART
NUMBER PART CODE DESCRIPTION QTY
1 GF26BL.00.01
GF26BL.A0.01
TM8264.00.00
TODXL1.A1.UL
WODQ10.02.06
GF26BL.10.03
TODXD1.44.UL
GF26BL.10.01
GF26BL.10.04
GF26BL.10.30
GF26BL.10.40
TM8201.00.01
BOB1WL.08.LH
1
1
1
1
1
1
1
1
1
1
1
3
1
2
3
4
5
6
7
8
9
10
11
12
13
Blower Tube
Right motor shell assembly
Motor assembly
Wire
Micro-switch
Switch button
Buit-in plug
Left motor shell
Shaft housing
Heat output fan blade
Fan blade
Pressure pad
Nut
PARTS LIST
17

Make sure your extension cord is in good condition. When using an extension cord, be sure to
use one heavy enough to carry the current your product will draw. A wire gauge size (A.W.G.)
of at least 14 is recommended for an extension cord 50 feet or less in length. If in doubt, use
the next heavier gauge. The smaller the gauge number, the heavier the cord. An undersized
cord will cause a drop in line voltage resulting in loss of power and overheating.
Do not point the blower nozzle in the direction of people or pets.
Never place blower on any surface, except a hard, clean surface when motor is running.
Gravel, sand, and other debris can be picked up by the air inlet and thrown at the operator or
bystanders, causing possible serious injuries.
Never run the unit without the proper equipment attached. Always ensure the blower tubes are
installed.
When not in use, blower should be stored indoors in a dry, locked up place—out of the reach
of children.
Maintain tool with care. Keep fan area clean for best and safest performance. Follow instructions
for proper maintenance.
Do not attempt to clear clogs from tool without first unplugging it.
Do not pull or carry by cord, use cord as a handle, or pull cord around sharp edges or corners.
Keep cord away from heated surfaces.
Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
To reduce the risk of electrical shock, do not expose to rain, do not use on wet surfaces.
Store indoors.
If the power supply cord is damaged, it must be replaced only by the manufacturer or by an
authorized service center to avoid risk.
Protect your lungs. Wear a face or dust mask if the operation is dusty. Following this rule will
reduce the risk of serious personal injury.
Save these instructions. Refer to them frequently and use them to instruct others who may use
this power tool. If you loan someone this power tool, loan them these instructions also.
SPECIFIC SAFETY RULES
5

WARNING:
Do not use this product if any parts on the Packing List are already assembled to your product
when you unpack it. Parts on this list are not assembled to the product by the manufacturer and
require customer installation. Use of a product that may have been improperly assembled could
result in serious personal injury.
WARNING:
If any parts are damaged or missing do not operate this product until the parts are replaced.
Use of this product with damaged or missing parts could result in serious personal injury.
WARNING:
Do not attempt to modify this product or create accessories not recommended for use with this
product. Any such alteration or modification is misuse and could result in a hazardous condition
leading to possible serious personal injury.
WARNING:
Do not connect to power supply until assembly is complete. Failure to comply could result in
accidental starting and possible serious personal injury.
UNPACKING
This product requires assembly.
Carefully remove the product and any accessories from the box. Make sure that all items listed
in the packing list are included.
Inspect the product carefully to make sure no breakage or damage occurred during shipping.
Do not discard the packing material until you have carefully inspected and satisfactorily
operated the product.
If any parts are damaged or missing, please call Customer service for assistance.
PACKING LIST
Blower
Blower Tube
Operator’s Manual
ASSEMBLY
10

WARRANTY
15
We take pride in producing a high quality, durable product. This Lawnmaster® product carries a
limited two (2) year warranty against defects in workmanship and materials from date of purchase
under normal household use. If product is to be used for commercial, industrial or rental use, a 30
day limited warranty will apply. Batteries carry a one-year warranty against defects in workmanship
and materials. Batteries must be charged in accordance with the operator's manual directions and
regulations in order to be valid. Warranty does not apply to defects due to direct or indirect abuse,
negligence, misuse, accidents, repairs or alterations and lack of maintenance.
Please keep your receipt/packing list as proof of purchase. This warranty gives you specific legal
rights, and you may have other rights, which vary from state to state.
For product service call Customer Service at [phone].
Items not covered by warranty :
1. Any part that has become inoperative due to misuse, commercial use, abuse, neglect, accident,
improper maintenance, or alteration; or
2. The unit, if it has not been operated and/or maintained in accordance with the owner's manual; or
3. Normal wear, except as noted below;
4. Routine maintenance items such as lubricants, blade sharpening;
5. Normal deterioration of the exterior finish due to use or exposure.
Transportation Charges : Transportation charges for the movement of any power equipment unit or
attachment are the responsibility of the purchaser. It is the purchaser’s responsibility to pay
transportation charges for any part submitted for replacement under this warranty unless such
return is requested in writing by LawnMaster.
SAVE YOUR RECEIPTS. THIS WARRANTY IS VOID WITHOUT THEM.