LD LDMIX6AG2 User manual

USER´S MANUAL
BEDIENUNGSANLEITUNG
MANUEL D`UTILISATION
MANUAL DE USUARIO
INSTRUKCJA OBSŁUGI
MANUALE D‘ USO
LD STINGER MIX G2 SERIES
ACTIVE 2-WAY LOUDSPEAKER WITH 4-CHANNEL MIXER
LDMIX6AG2
PASSIVE 2-WAY LOUDSPEAKER
LDMIX6G2

Introduction
The compact and lightweight Stinger MIX6G2 and MIX6AG2 active and passive speakers feature 6.5" woofers and
a 1" tweeter with a frequency response of 80 Hz to 20 kHz and an 80° x 70° beam angle. Once combined, they are
perfect for small PA and monitor applications. The integrated mixer of the MIX6AG2 offers a line and 3 mic channels
with 2-band EQ, switchable Hi-Z input, RCA record outputs, phantom power and 24-bit digital effects.
2
ENGLISHDEUTSCHFRANCAIS
FRANCAISFRANCAIS FRANCAISFRANCAIS ESPAÑOLPOLSKIITALIANO
You‘ve made the right choice!
We have designed this product to operate reliably over many years. LD Systems stands for this with its name and
many years of experience as a manufacturer of high-quality audio products.
Please read this User‘s Manual carefully, so that you can begin making optimum use of your LD Systems product
quickly.
You can find more information about LD SYSTEMS at our Internet site WWW.LD-SYSTEMS.COM

LDMIX6AG2
ACTIVE 2-WAY SPEAKER WITH 4 CHANNEL MIXER
LDMIX6G2
PASSIVE 2-WAY SPEAKER
3
ITALIANO
POLSKI
ESPAÑOL
FRANCAIS
FRANCAIS FRANCAIS FRANCAIS FRANCAIS
DEUTSCH
ENGLISH

4
ENGLISHDEUTSCHFRANCAIS
FRANCAISFRANCAIS FRANCAISFRANCAIS ESPAÑOLPOLSKIITALIANO
Avoid direct sunlight!
PREVENTIVE MEASURES:
1. Please read these instructions carefully.
2. Keep all information and instructions in a safe place.
3. Follow the instructions.
4. Observe all safety warnings. Never remove safety warnings or other information from the equipment.
5. Use the equipment only in the intended manner and for the intended purpose.
6. Use only sufficiently stable and compatible stands and/or mounts (for fixed installations). Make certain that wall
mounts are properly installed and secured. Make certain that the equipment is installed securely and cannot fall down.
7. During installation, observ e the applicable safety regulations for your country.
8. Never install and operate the equipment near radiators, heat registers, ovens or other sources of heat. Make certain
that the equipment is always installed so that is cooled sufficiently and cannot overheat.
9. Never place sources of ignition, e.g., burning candles, on the equipment.
10. Ventilation slits must not be blocked.
11. Do not use this equipment in the immediate vicinity of water (does not apply to special outdoor equipment -
in this case, observe the special instructions noted below. Do not expose this equipment to flammable materials,
fluids or gases.
12. Make certain that dripping or splashed water cannot enter the equipment. Do not place containers filled with
liquids, such as vases or drinking vessels, on the equipment.
13. Make certain that objects cannot fall into the device.
14. Use this equipment only with the accessories recommended and intended by the manufacturer.
15. Do not open or modify this equipment.
16. After connecting the equipment, check all cables in order to prevent damage or accidents, e.g., due to
tripping hazards.
17. During transport, make certain that the equipment cannot fall down and possibly cause property damage and
personal injuries.
18. If your equipment is no longer functioning properly, if fluids or objects have gotten inside the equipment or
if it has been damaged in anot her way, switch it off immediately and unplug it from the mains outlet (if it is a
powered device). This equipment may only be repaired by authorized, qualified personnel.
19. Clean the equipment using a dry cloth.
20. Comply with all applicable disposal laws in your country. During disposal of packaging, please separate
plastic and paper/cardboard.
21. Plastic bags must be kept out of reach of children.
FOR EQUIPMENT THAT CONNECTS TO THE POWER MAINS:
22. CAUTION: If the power cord of the device is equipped with an earthing contact, then it must be connected to
an outlet with a protective ground. Never deactivate the protective ground of a power cord.
23. If the equipment has been exposed to strong fluctuations in temperature (for example, after transport), do
not switch it on immediately. Moisture and condensation could damage the equipment. Do not switch on the
equipment until it has reached room temperature.
24. Before connecting the equipment to the power outlet, first verify that the mains voltage and frequency match
the values specified on the equipment. If the equipment has a voltage selection switch, connect the equipment to
the power outlet only if the equipment values and the mains power values match. If the included power cord or
power adapter does not fit in your wall outlet, contact your electrician.
25. Do not step on the power cord. Make certain that the power cable does not become kinked, especially at the
mains outlet and/or power adapter and the equipment connector.
26. When connecting the equipment, make certain that the power cord or power adapter is always freely
accessible. Always disconnect the equipment from the power supply if the equipment is not in use or if you want

5
ITALIANO
POLSKI
ESPAÑOL
FRANCAIS
FRANCAIS FRANCAIS FRANCAIS FRANCAIS
DEUTSCH
ENGLISH
To prevent possible hearing damage, avoid listening at high volume levels over long periods of time.
Even exposure to short bursts of loud noise can result in hearing loss. Please keep the volume
constantly at a comfortable level.
Avoid direct sunlight!
SAFETY:
to clean the equipment. Always unplug the power cord and power adapter from the power outlet at the plug or
adapter and not by pulling on the cord. Never touch the power cord and power adapter with wet hands.
27. Whenever possible, avoid switching the equipment on and off in quick succession because otherwise this
can shorten the useful life of the equipment.
28. IMPORTANT INFORMATION: Replace fuses only with fuses of the same type and rating. If a fuse blows repea-
tedly, please contact an authorised service centre.
29. To disconnect the equipment from the power mains completely, unplug the power cord or power adapter
from the power outlet.
30. If your device is equipped with a Volex power connector, the mating Volex equipment connector must be
unlocked before it can be removed. However, this also means that the equipment can slide and fall down if
the power cable is pulled, which can lead to personal injuries and/or other damage. For this reason, always be
careful when laying cables.
31. Unplug the power cord and power adapter from the power outlet if there is a risk of a lightning strike or
before extended periods of disuse.
CAUTION
RISK OF ELECTRIC S HOCK
DO NOT O PEN
CAUTION:
Never remove the cover, because otherwise there may be a risk of electric shock. There are no user serviceable
parts inside. Have repairs carried out only by qualified service personnel.
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user
to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electrical shock.
The exclamation mark within an equilateral triangle is intended to alert the user to the presence of
important operating and maintenance instructions.
CAUTION – HIGH VOLUME LEVELS WITH AUDIO PRODUCTS!
This equipment is intended for professional use. Therefore, commercial use of this equipment is subject to the
respectively applicable national accident prevention rules and regulations. As a manufacturer, Adam Hall is
obligated to notify you formally about the existence of potential health risks.
Hearing damage due to high volume and prolonged exposure: When in use, this product is capable of producing
high sound-pressure levels (SPL) that can lead to irreversible hearing damage in performers, employees, and
audience members. For this reason, avoid prolonged exposure to volumes in excess of 90 dB.

CONNECTIONS, CONTROLS, AND INDICATORS:
6
ENGLISHDEUTSCHFRANCAIS
FRANCAISFRANCAIS FRANCAISFRANCAIS ESPAÑOLPOLSKIITALIANO
111
2
3 23
4
5 5 5 5 6 6 6 67 7 7 7
8 8 8 8
9
10 11
12
13 14 15 16 19
20 21 22
17 18
LDMIX6AG2:

CONNECTIONS, CONTROLS, AND INDICATORS:
1MIC INPUT CH1 - CH3
Balanced microphone input (XLR/ 6.3 mm jack combo) It is also possible to use an unbalanced microphone
cable (mono jack). A 15 V phantom power can be switched on (switch 22).
2HI-Z
Using this pressure switch, the input of channel 1 (CH1) can be switched to high impedance (push switch
down for activation). Channel 1 can thus be used as a channel for instruments such as an electric guitar.
3LINE INPUT CH4 (RCA L/R)
Unbalanced line input (RCA) for connecting an external audio source (e.g., laptop, MP3 player). A stereo
signal is mono summed internally.
4LINE INPUT CH4 (3.5 MM STEREO JACK)
Unbalanced Line Input with a 3.5 mm stereo jack. A stereo signal is mono summed internally.
5HIGH
Equalizer high band (12 kHz) for input channels 1 to 4 (CH1 - CH4). When turned to the left, levels are lowe-
red, when turned to the right, they are raised. In the centre position (resting point), the equalizer is inactive.
6LOW
Equalizer low band (80 Hz) for input channels 1 to 4 (CH1 - CH4). When turned to the left, levels are lowered,
when turned to the right, they are raised. In the centre position (resting point), the equalizer is inactive.
7LEVEL
Volume control for channels 1 to 4 (CH1 - CH4).
7
ITALIANO
POLSKI
ESPAÑOL
FRANCAIS
FRANCAIS FRANCAIS FRANCAIS FRANCAIS
DEUTSCH
ENGLISH
LDMIX6AG2:
24
25
26

CONNECTIONS, CONTROLS, AND INDICATORS:
8DFX
Effect Send controls for channels 1 to 4 (CH1 - CH4). The signal of the corresponding channel is tapped
behind the volume control (post-fader) and routed to the internal effects processor (DSP), according to the
setting of the Effect Send knob. It is important to ensure that the internal input of the effects unit is not
overloaded (watch the PEAK LED).
9PRESETS
Endless rotary switch for selecting one of the 16 internal digital effects. A list of all effects is located right
next to the controls on the effects unit (DSP).
10 DFX RET
By using the effects return knob, the effect signal can be mixed to the sum signal (MAIN signal).
11 MUTE
By pressing the MUTE button, the internal effect unit is muted, and the PEAK LED is continuously on. Pressing
once again cancels the mute status and the PEAK LED goes out.
12 PEAK LED
The PEAK LED lights up if the input to the internal effects processor is clipping (turn down the effect send
level DFX in channels 1 to 4 ), or if the internal effects unit is muted (MUTE).
13 LOW
Equalizer bass band (80 Hz) for the sum channel. When turned to the left, levels are lowered, when turned to
the right, they are raised. In the centre position (resting point), the equalizer is inactive.
14 MID
Equalizer mid band (2.5 kHz) for the sum channel. When turned to the left, levels are lowered, when turned to
the right, they are raised. In the centre position (resting point), the equalizer is inactive.
15 HIGH
Equalizer high band (12 kHz) for the sum channel. When turned to the left, levels are lowered, when turned to
the right, they are raised. In the centre position (resting point), the equalizer is inactive.
16 MAIN LEVEL
Volume control of the sum channel (total volume).
17 MAIN LEVEL METER
4 segment level meter for the sum channel. Once the peak LED (PK) lights up, the device is operating at
the distortion limit. It is not critical if the LED lights briefly at peak levels for the incoming signal, however
continuous illumination should be avoided by reducing the volume.
8
ENGLISHDEUTSCHFRANCAIS
FRANCAISFRANCAIS FRANCAISFRANCAIS ESPAÑOLPOLSKIITALIANO

CONNECTIONS, CONTROLS, AND INDICATORS:
18 POWER-LED
Lights up once the system is properly connected to the power mains and switched on.
19 MONITOR
Volume control on the monitor channel. The signal corresponds to the sum signal and is tapped before the
volume control of the sum channel (MAIN LEVEL), and is therefore independently adjustable.
20 MONITOR OUT
Balanced mono output with 6.3 mm jack. Connection possibility for a further active speaker. Level adjustment
via the MONITOR volume control (No. 19).
21 MAIN POWER OUT
Output (6.3 mm jack) with 70 W RMS amplifier power for a passive speaker (e.g. LDMIX6G2 The impedance
of the connected speakers should not be less than 4 ohm. The volume is set to be parallel with the master
volume on the volume control MAIN LEVEL (No. 16). The signal corresponds to the sum signal.
22 PHANTOM ON / OFF
Switchable 15 V phantom power for the microphone inputs on channels 1 to 3 (CH1 - CH3). In "ON" position,
the phantom power is on and off in the "OFF" position.
23 REC OUT
Line output on RCA connectors. The present signal corresponds to the sum signal and is tapped before the
volume control of the sum channel (MAIN LEVEL), and is therefore independently adjustable.
24 110 - 120 V / 220 - 240 V
Switch for setting the operating voltage. The mains voltage of your power supplier and the operating voltage
of the device must be the same!
25 IEC POWER SOCKET WITH INTEGRAL FUSE HOLDER
IMPORTANT INFORMATION: BEFORE using this equipment, make certain that the mains voltage of your
energy utility and the operating voltage of the device match! Always replace the fuse with a fuse of the same
type and values according to the supply voltage (see label on the rear panel)
If the fuse blows repeatedly, please contact an authorised service centre.
26 POWER ON / OFF
On / Off switch for the power supply of the device.
9
ITALIANO
POLSKI
ESPAÑOL
FRANCAIS
FRANCAIS FRANCAIS FRANCAIS FRANCAIS
DEUTSCH
ENGLISH

INPUT
The speaker input (6.3 mm jack) is located on the back of the passive MIX6G2 speaker cabinet.
CONNECTIONS, CONTROLS, AND INDICATORS:
10
ENGLISHDEUTSCHFRANCAIS
FRANCAISFRANCAIS FRANCAISFRANCAIS ESPAÑOLPOLSKIITALIANO
LDMIX6G2:

ACCESSORIES:
A 16 mm pole mount is located on the right side and on the bottom of the MIX6AG2 and MIX6G2 speakers. The
matching stand is available under item number LDST40.
11
ITALIANO
POLSKI
ESPAÑOL
FRANCAIS
FRANCAIS FRANCAIS FRANCAIS FRANCAIS
DEUTSCH
ENGLISH

WIRING EXAMPLE:
12
ENGLISHDEUTSCHFRANCAIS
FRANCAISFRANCAIS FRANCAISFRANCAIS ESPAÑOLPOLSKIITALIANO

WIRING EXAMPLE:
LDMIX6G2
Hard disk Recording
CD/MP3 Playback
13
ITALIANO
POLSKI
ESPAÑOL
FRANCAIS
FRANCAIS FRANCAIS FRANCAIS FRANCAIS
DEUTSCH
ENGLISH

Model Name: LDMIX6AG2
Product Type: PA speaker with integrated mixer
Type: active
Woofer Size: 6.5"
Woofer Size: 165.1 mm
Woofer Brand: custom made
Tweeter Size: 1"
Tweeter Size: 25 mm
Tweeter Brand: custom made
Dispersion Angle (H x V): 80° x 70°
Frequency Response: 80 Hz - 20,000 Hz
Amplifier: class D
Amplifier Power (RMS): 2 x 70 W
Amplifier Power (Peak): 2 x 140 W
Max SPL: 122 dB
Protection: limiter, short circuit, over voltage, overload, temperature
Mixer
Channels: 4
Microphone Input Channels: 3
Connector Type Microphone Inputs: XLR/ 6.3 mm jack (combo)
Controls for Microphone Input Channels: EQ High, EQ Low, DFX Send, Level, Hi-Z Switch (channel
1 only)
Line Input Channels: 1
Connector Type Line Input Channels: 3.5 mm stereo jack, 2 x RCA
Controls Line Input Channels: EQ High, EQ Low, DFX Send, Level
Monitor Line Outputs: 1
Connector Type Monitor Line Output: 6.3 mm jack (balanced)
Controls for Monitor Line Output: Monitor Volume
Record Output: 1
Connector Type Record Output: 2 x RCA
Reinforced Main Output: 1
Connector Type Reinforced Main Output: 6.3 mm (min. 4 Ohm impedance)
SPECIFICATIONS:
14
ENGLISHDEUTSCHFRANCAIS
FRANCAISFRANCAIS FRANCAISFRANCAIS ESPAÑOLPOLSKIITALIANO

SPECIFICATIONS:
DSP digital effects unit
DSP Number of Programs: 16
DSP Controls: Presets, DFX return, Mute switch
DSP Display Elements: Peak LED
Main Section
Main Section Controls: EQ Low, EQ Mid, EQ High, Main Level, Phantom Power,
switch operating voltage, power switch
Phantom Power: 15 V
Main Section Indicators: 4 segment LED level meter, power LED
Power Socket: IEC power socket
Power Supply: transformer
Operating Voltage: 110 V AC - 120 V AC, 50 - 60 Hz
220 V AC - 240 V AC, 50 - 60 Hz
Power Consumption (max.): 180 W
Cabinet
Cabinet Type: bass reflex
Housing Material: MDF
Housing Surface: textured coating
Housing Colour: black
Width: 323 mm
Height: 214 mm
Depth: 222 mm
Weight: 6.73 kg
Other Features: 2 x 16 mm pole mount socket, rubber feet
15
ITALIANO
POLSKI
ESPAÑOL
FRANCAIS
FRANCAIS FRANCAIS FRANCAIS FRANCAIS
DEUTSCH
ENGLISH

Model Name: LDMIX6G2
Product Type: PA Speakers
Type: passive
Woofer Size: 6.5"
Woofer Size: 165.1 mm
Woofer Brand: custom made
Tweeter Size: 1"
Tweeter Size: 25 mm
Tweeter Brand: custom made
Dispersion Angle (H x V): 80° x 70°
Frequency Response: 80 Hz - 20,000 Hz
Rated load (RMS): 70 W
Rated load (peak): 140 W
Impedance: 4 ohms
Sensitivity (1W/1m): 90 dB
Max SPL: 122 dB
Speaker Connections: 1
Connector Type Speaker Connection: 6.3 mm jack
Cabinet Type: bass reflex
Housing Material: MDF
Housing Surface: textured coating
Housing Colour: black
Width: 323 mm
Height: 214 mm
Depth: 222 mm
Weight: 4.22 kg
Other Features: 2 x 16 mm pole mount socket, rubber feet
SPECIFICATIONS:
16
ENGLISHDEUTSCHFRANCAIS
FRANCAISFRANCAIS FRANCAISFRANCAIS ESPAÑOLPOLSKIITALIANO

17
ITALIANO
POLSKI
ESPAÑOL
FRANCAIS
FRANCAIS FRANCAIS FRANCAIS FRANCAIS
DEUTSCH
ENGLISH
MANUFACTURER´S DECLARATIONS:
MANUFACTURER‘S WARRANTY
This warranty extends to the LD SYSTEMS branded product you purchased from Adam Hall. The statutory warranty
rights against the vendor shall not be affected by this warranty. Rather, this warranty gives you additional independent
claims against Adam Hall.
With this warranty, Adam Hall ensures that products you have purchased from Adam Hall or Adam Hall partners,
under normal use, are free of defects in material or workmanship for a period of 2 years from the date of purchase.
The warranty period begins on the date of purchase. In order to assert a claim for warranty service, the proof of
date of purchase is provided by the receipt bearing the date of purchase or the date of purchase on the delivery
note. You are entitled to warranty service under the conditions and provisions set out in this document, if a repair
within the warranty period is required.
This warranty applies only to the original purchaser of the products supplied by Adam Hall and is not transferable
to any person to whom the property is transferred by the original purchaser.
Within the warranty period, the defective parts or the product from Adam Hall will be repaired or replaced. Under
the terms of this warranty, all the replaced or removed components become the property of Adam Hall.
In the unlikely event that a product acquired from Adam Hall, repeatedly exhibits a defect, Adam Hall may decide,
at its discretion, to replace this product with a comparable product of at least the same performance.
Adam Hall does not guarantee that the operation of this product will be uninterrupted or error-free. Adam Hall
accepts no responsibility for any damage due to incorrect compliance with the instructions received in the delivery.
This warranty does not extend to:
- wearing parts (eg battery, tubes).
- devices that have had their serial number removed or damaged, or failed as a result of an accident
- inappropriate or abusive use or other external causes
- devices that were not used in accordance with the operating parameters defined in the user documentation
shipped with the product
- devices that have been repaired using parts not made or distributed by Adam Hall
- devices that have been serviced, modified or repaired by someone other than Adam Hall or an authorised service partner.
These terms and conditions constitute the complete and exclusive warranty agreement between you and Adam
Hall regarding the Adam Hall branded product you have purchased.
This warranty is valid only within Europe. Outside of Europe please contact our official distributors.

18
ENGLISHDEUTSCHFRANCAIS
FRANCAISFRANCAIS FRANCAISFRANCAIS ESPAÑOLPOLSKIITALIANO
MANUFACTURER´S DECLARATIONS:
LIMITATION OF LIABILITY
If your Adam Hall branded hardware product fails to work as warranted above, your sole and exclusive remedy
shall be repair or replacement. Adam Halls’ maximum liability under this limited warranty is expressly limited to
the lesser of the price you have paid for the product or the cost of repair or replacement of any components that
malfunction under conditions of normal use.
Adam Hall is not liable for any damages caused by the product or the failure of the product, including any lost
profits or savings or special, incidental, or consequential damages. Adam Hall is not liable for any claim made by
a third party or made by you for a third party.
This limitation of liability applies whether damages are sought, or claims are made, under this Limited Warranty
or as a tort claim (including negligence and strict product liability), a contract claim, or any other claim, and
cannot be rescinded or changed by anyone. This limitation of liability will be effective even if you have advised
Adam Hall or an authorized representative of Adam Hall of the possibility of any such damages, but not, however,
in the event of claims for damages in connection with personal injuries.
This manufacturer‘s warranty grants you specific rights; depending on jurisdiction (nation or state), you may be
be entitled to additional claims. You are advised to consult applicable state or national laws for a full determina-
tion of your rights.
REQUESTING WARRANTY SERVICE
To request warranty service for the product, contact Adam Hall or the Adam Hall authorized reseller from which
you purchased the product.
EC DECLARATION OF CONFORMITY
The equipment marketed by Adam Hall complies (where applicable) with the essential requirements and other
relevant specifications of Directives 1999/5/EC (R&TTE), 2004/108/EC (EMC) und 2006/95/EC (LVD). Additional
information can be found at www.adamhall.com.

19
ITALIANO
POLSKI
ESPAÑOL
FRANCAIS
FRANCAIS FRANCAIS FRANCAIS FRANCAIS
DEUTSCH
ENGLISH
MANUFACTURER´S DECLARATIONS:
PROPER DISPOSAL OF THIS PRODUCT
(Valid in the European Union and other European countries with waste separation)
This symbol on the product, or the documents accompanying the product, indicates that this appliance may not
be treated as household waste. This is to avoid environmental damage or personal injury due to uncontrolled
waste disposal. Please dispose of this product separately from other waste and have it recycled to promote
sustainable economic activity.
Household users should contact either the retailer where they purchased this product, or their local government
office, for details on where and how they can recycle this item in an environmentally friendly manner.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This
product should not be mixed with other commercial wastes for disposal .
ENVIRONMENTAL PROTECTION AND ENERGY CONSERVATION
Energy conservation is an active contribution to environmental protection. Please turn off all unneeded electrical
devices. To prevent unneeded devices from consuming power in standby mode, disconnect the mains plug.
Adam Hall GmbH, all rights reserved. The technical data and the functional product characteristics can be subject
to modifications. The photocopying, the translation, and all other forms of copying of fragments or of the integrlity
of this user’s manual is prohibited.

Einführung
Die kompakten und leichten Stinger MIX6AG2 aktiv und Stinger MIX6G2 Passivlautsprecher verfügen über 6,5“
Tieftöner und einen 1“ Hochtöner mit einem Frequenzgang von 80 Hz bis 20 kHz und 80° x 70° Abstrahlwinkel.
Sie sind in Kombination perfekt für kleine PA- und Monitoranwendungen geeignet. Der integrierte Mixer des
MIX6AG2 bietet einen Line- und 3 Mikrofonkanäle mit 2-Band Equalizer, einen schaltbaren Hi-Z-Eingang, Cinch-
Aufnahmeausgänge, Phantomspeisung und 24-Bit Digitaleffekte.
20
ENGLISHDEUTSCHFRANCAIS
FRANCAISFRANCAIS FRANCAISFRANCAIS ESPAÑOLPOLSKIITALIANO
Sie haben die richtige Wahl getroffen!
Dieses Gerät wurde unter hohen Qualitätsanforderungen entwickelt und gefertigt, um viele Jahre einen reibungs-
losen Betrieb zu gewährleisten. Dafür steht LD Systems mit seinem Namen und der langjährigen Erfahrung als
Hersteller hochwertiger Audioprodukte.
Bitte lesen Sie diese Bedienungsanleitung sorgfältig, damit Sie Ihr neues Produkt von LD Systems schnell optimal
einsetzen können.
Mehr Informationen zu LD SYSTEMS finden Sie auf unserer Internetseite WWW.LD-SYSTEMS.COM