LDDE NanoPixSlim FR1440 User manual

Page 1
Short instruction
NanoPixSlim FR1440
from software version: V2.0
Released: 12-2017 - V1.1 - Rev B
Lighting
Design
Development
Electronics
LDDE Vertriebsgesellschaft m. b. H.
Simmeringer Hauptstrasse 357, 1110 Vienna, Austria
P: [phone], F: [phone]
E: of[email protected]; W: www.ldde.com
LDDE Vertriebsgesellschaft GmbH reserves the right, without prior notice, changes to the product and specication

Page 2
Safety Guidelines
Lighting
Design
Development
Electronics
LDDE Vertriebsgesellschaft m. b. H.
Simmeringer Hauptstraße 357, 1110 Wien, Austria
P: [phone], F: [phone]
E: of[email protected]; W: www.ldde.com
LDDE Vertriebsgesellschaft GmbH reserves the right, without prior notice, changes to the product and specication
» Please read these safety guidelines carefully before you take the
NanoPixSlim FR1440 into service.
» Check the suitability of the product for the intended use.
» The NanoPixSlim FR1440 is not suitable for outdoor use (IP20).
» Do not attempt to repair or dismantle the NanoPixSlim FR1440 xture:
Opening and removing the internal covers can result in electrocution or
other serious injuries.
» In case of product failure, please contact LDDE or an authorised LDDE-deal-
ership.
» Do not touch the xture while it is in use.
» Disconnent the xture from the power supply before re-positioning and
cleaning.
» Ensure that when the luminaire systems are installed in decorations, a
sufcient clearance of around 30cm is required for adequate cooling and
ventilation.
» Protect the xture from shocks and impacts.
» Protect the xture from moisture and water and avoid contact with moist or
wet appliances.
» Ensure that the xture is not covered and adequate ventilation is in place.
» Do not insert objects into openings of the housing that are connected to live
parts as this can lead to short circuiting. Danger of electric shock and risk
of re.
» The xture is to be removed from service if:
• there is visible damage
• parts have become lose
• there is visible damage to cable connections
» LDDE products are manufactured and delivered in concordance with EU
directive 2002/96/EU of the European Parliament and the Council on
Waste Electrical and Electronic Equipment WEEE). Help protect the en-
vironment and dispose of used products at your local recycling station.
Your dealership can offer further advice on correct disposal.

Page 3
Overview DMX Modes
Lighting
Design
Development
Electronics
LDDE Vertriebsgesellschaft m. b. H.
Simmeringer Hauptstrasse 357, 1110 Vienna, Austria
P: [phone], F: [phone]
E: of[email protected]; W: www.ldde.com
You can choose between 5 DMX modes each designed for different applications and
preferences:
CH5 - COLOR MODE (5 CHANNELS):
Only colors (RGB,WW,CW) - No Intensity and Strobe channel available.
CH6 - MASTER COLOR MODE (6 CHANNELS):
Intensity and Colors.
CH7 - NORMAL MODE (7 CHANNELS):
Most common mode with all basic functions.
CH10 - HIGH RESOLUTION COLOR MODE (10 CHANNELS)
Same as the Ch5 - Color Mode but with 16-bit dimming.
CH11 - HIGH RESOLUTION COLOR STROBE MODE (11 CHANNELS)
Same as Ch10 - High Resolution Color Mode but with 8-bit strobe.
LDDE Vertriebsgesellschaft GmbH reserves the right, without prior notice, changes to the product and specication

Page 4
DMX Chart
Lighting
Design
Development
Electronics
LDDE vertriebsgesellschaft m. b. H.
Simmeringer Hauptstrasse 357, 1110 Vienna, Austria
P: [phone], F: [phone]
E: ofcelddecom; W: www.ldde.com
Channel 8-bit interpolated Ch5 - 5 Channel
(905)
Ch6 - 6 Channel
(906)
Ch7 - 7 Channel
(907)
1 Intensity xxx 1 1
2 R (red) 1 2 2
3G (green) 2 3 3
4 B (blue) 34 4
5 WW (warm white) 4 5 5
6 CW (cold white) 5 6 6
7 Strobe xxx xxx 7
Channel 16-bit Ch10 - 10 Channel
(910)
Ch11 - 11 Channel
(911)
1 Red 1 1
2Red ne 2 2
3Green 3 3
4Green ne 4 4
5 Blue 5 5
6Blue ne 6 6
7 Warm White 7 7
8Warm White ne 8 8
9 Cold White 9 9
10 Cold White ne 10 10
11 Strobe xxx 11
Operating Mode
The table below shows the different available modes and the DMX channels required for the corresponding
mode.
In brackets, the BCD & Remote command is used to set the desired
mode.
For example. To switch to the Ch10 -High Resolution Color Mode, use
910 on the BCD switch.
LDDE Vertriebsgesellschaft GmbH reserves the right, without prior notice, changes to the product and specication

Page 5
Changes with BCD switch possible only before commissioning!
Changes with LDDE RemoteControl possible only during operation!
The respective mode can be changed by means of BCD switch or
LDDE RemoteControl.
Changes to the setting and/or DMX addresses affect all LDDE devices which are addressed via the
same DMX cable!
Changing Operating Mode
Lighting
Design
Development
Electronics
LDDE Vertriebsgesellschaft m. b. H.
Simmeringer Hauptstrasse 357, 1110 Vienna, Austria
P: [phone], F: [phone]
E: of[email protected]; W: www.ldde.com
Settings with BCD switch
The settings of the NanoPixSlim FR1440 can be made using the BCD switch on the back of the device,
therefore the NanoPixSlim FR1440 must be disconnected from the power supply.
To make changes, please proceed as follows.
1. Disconnect NanoPixSlim FR1440 from the power supply!
2. Set the desired mode to the BCD switch.
3. Connect NanoPixSlim FR1440 back to power supply.
4. Status LED and LEDs on the NanoPixSlim FR1440 illuminate “blue” for approx. 2 seconds.
5. Set the desired DMX start address again.
Settings with LDDE RemoteControl
To change the settings of the NanoPixSlim FR1440, you need a LDDE RemoteControl.
This allows various changes to the basic settings and the DMX mode during operation.
To change the settings on the NanoPixSlim FR1440 with the LDDE RemoteControl,
please follow the steps below.
1. Disconnect the DMX connection to the NanoPixSlim FR1440.
2. Please note that no devices that could perform DMX value changes, such as a light console, are
connected to this DMX line.
3. Connect the Power/DMX cable between NanoPixSlim FR1440 and the LDDE RemoteControl.
4. Send the desired setting or DMX address to the NanoPixSlim FR1440.
5. After sending, the LEDs of the NanoPixSlim FR1440 light up in the following colors.
green ............................................................................................................................. DMX address
blue................................................................................................................... Settings / Parameters
red ............................................................................................................................Invalid command
LDDE Vertriebsgesellschaft GmbH reserves the right, without prior notice, changes to the product and specication

Page 6
Overview Settings
Lighting
Design
Development
Electronics
LDDE vertriebsgesellschaft m. b. H.
Simmeringer Hauptstrasse 357, 1110 Vienna, Austria
P: [phone], F: [phone]
E: ofcelddecom; W: www.ldde.com
LDDE Vertriebsgesellschaft GmbH reserves the right, without prior notice, changes to the product and specication
Command Function
801 - Disabled Fade to Zero off
802 - Enabled Fade to Zero on
850 - Disabled Status LED off
851 - Enabled Status LED on
860 - Disabled Safety Light off
861 - Low Safety Light on - „Low“
862 - Medium Safety Light on - „Medium“
863 - High Safety Light on - „High“
865 - red Safety Light „red“
866 - green Safety Light „green“
867 - blue Safety Light „blue“
868 - warm white Safety Light „warm white“
869 - cold white Safety Light „cold white“
880 - PWM 8kHz PWM frequency set to 8kHz
858 - PWM 5,8kHz PWM frequency set to 5,8kHz
890 - Disabled DMX Indicator off
891 - Enabled DMX Indicator on
921 - Linear No characteristic is used
922 - Normal Normal dimming curve is used
923 - Smooth Smooth dimming curve is used
930 - Disabled Working Light off
931 - Enabled Working Light on
935 - Enabled 50% Working Light at 50% Intensity
937 - Enabled 70% Working Light at 70% Intensity
939 - Enabled 100% Working Light at 100% Intensity
666 - Reset Reset to factory default

Page 7
Settings & Modes
Lighting
Design
Development
Electronics
LDDE vertriebsgesellschaft m. b. H.
Simmeringer Hauptstrasse 357, 1110 Vienna, Austria
P: [phone], F: [phone]
E: ofcelddecom; W: www.ldde.com
Factory Default
Channelmode Ch7 - Normal Mode
Dimming parameter Normal
Work light disabled
PWM frequency 8kHz
Safety Light / Color disabled / blue
DMX indicator disabled
Fade to Zero enabled
Status LED enabled
The NanoPixSlim FR1440 is delivered with factory settings in 7Ch - Normal mode, which can be changed via
the BCD switch on the back of the device or with a LDDE RemoteControl.
Fade to Zero
801 - Disabled For a new DMX value (below DMX value 15) --> Snap to 0
802 - Enabled For a new DMX value (below DMX value 15) is dimmed to 0.
Status LED
850 - Disabled The status LED is switched off.
851 - Enabled The status LED is switched on.
Safety Light
860 - Disabled Safety light function disabled
861 - Low Safety light function „Low“ enabled - minimum light output
862 - Medium Safety light function „Medium“ enabled - medium light output
863 - High Safety light function „High“ enabled - high light output
Available Colors
865 - red The „red“ LEDs light up with the intensity set.
866 - green The „green“ LEDs light up with the intensity set.
867 - blue The „blue“ LEDs light up with the intensity set.
868 - warm white The „warm white“ LEDs light up with the intensity set.
869 - cold white The „cold white“ LEDs light up with the intensity set.
First, activate the function in the desired intensity. Then select the desired color in which the device is to light
up. Finally, set the DMX address.
LDDE Vertriebsgesellschaft GmbH reserves the right, without prior notice, changes to the product and specication

Page 8
Settings & Modes
Lighting
Design
Development
Electronics
LDDE Vertriebsgesellschaft m. b. H.
Simmeringer Hauptstrasse 357, 1110 Vienna, Austria
P: [phone], F: [phone]
E: of[email protected]; W: www.ldde.com
DMX indicator
890 - Disabled The DMX indicator is switched off.
891 - Enabled The status LED is switched on.
If no DMX signal is present, the device ashes red.
Dimming parameters
921 - Linear „Linear“ no characteristic is used.
922 - Normal „Normal“ characteristic is used.
923 - Smooth „Smooth“ characteristic is used.
Working light
930 - Disabled Working light is disabled.
931 - Enabled If there is no DMX signal for 4 seconds --> WW & CW will be switched on.
935 - Enabled 50% Working light at 50% Intensity.
937 - Enabled 70% Working light at 70% Intensity.
939 - Enabled 100% Working light at 100% Intensity.
PWM frequency
880 - PWM 8kHz The PWM frequency is set to 8kHz.
858 - PWM 5,8kHz The PWM frequency is set to 5,8kHz.
Factory default
666 - Reset The device is reset to factory settings.
LDDE Vertriebsgesellschaft GmbH reserves the right, without prior notice, changes to the product and specication

Page 9
Technical Specications
Lighting
Design
Development
Electronics
LDDE vertriebsgesellschaft m. b. H.
Simmeringer Hauptstrasse 357, 1110 Vienna, Austria
P: [phone], F: [phone]
E: ofcelddecom; W: www.ldde.com
Dimensions / Weight
Length ................................................................................................................ 1204 mm / 47,40 Inches
Width ....................................................................................................................... 165 mm / 6,49 Inches
Height ...................................................................................................................... 57 mm / 2,24 Inches
Weight (without accessories)......................................................................................... 5,60 kg / 12,35 lb
Control
Protocol .............................................................................................................................. DMX512/1990
Dimming
Dimming .................................................................................................................................... 0 - 100%
DMX channels ......................................................................................... 5 / 6 / 7 / 10 / 11 DMX channels
Address setting .............................................................................. BCD switch or LDDE RemoteControl
Light Source
LED Engine ................................................................................................ RGB, warm white, cold white
Average life span .................................................................................................... approx. 30.000 hours
Connections
Input / Output .................................................................................................Power/Data multicore cable
Electrical specications
Input voltage range................................................................................................ 100-240VAC | 50/60Hz
Max. Power consumption ................................................................................................................... 80W
Construction
Housing ............................................................................................. Aluminium continous casting prole
Color ................................................................................................................................................ black
Minimum clearance of the LED ................................................................................ 100mm / 3,93 Inches
Minimum clearance for sufcient cooling ..............................................................300mm / 11,81 Inches
Cooling ..........................................................................................convection cooling for silent operation
Protection class .................................................................................................................................. IP20
Safty standards
Certications ......................................EN 55015, EN 60598-1, EN 61000-3-2, EN 61000-3-3, EN 61547
Photobiological safety according to IEC 62471:2008 / EN 62471:2008
Temperatures
Maximum ambient temperature..................................................................................... ta: +40ºC / 104°F
LDDE Vertriebsgesellschaft GmbH reserves the right, without prior notice, changes to the product and specication

Page 10
Dimensions
Lighting
Design
Development
Electronics
LDDE vertriebsgesellschaft m. b. H.
Simmeringer Hauptstrasse 357, 1110 Vienna, Austria
P: [phone], F: [phone]
E: ofcelddecom; W: www.ldde.com
LDDE Vertriebsgesellschaft GmbH reserves the right, without prior notice, changes to the product and specication