LEAB 1051009023 User manual

CAN-LIN Gateway
Quick start guide
V 2
Safety
This Quick Start Guide is intended to support safe handling of the
CAN-LIN Gateway.
The CAN-LIN Gateway allows the LPS II to be integrated into
the Mercedes-Benz Advanced Control (MBAC) and therefore
the most important data of the LPS II to be shown in the MBUX
multimedia display, on additional displays in the motorhome
body or the MBAC app.
In addition to the information on current and voltage for solar,
on-board network and external feed, the charging status of the
LPS II is also shown on the original vehicle display, along with
how to switch the 230 V inverter of the LPS II on and off.
Observe the safety instructions:
WARNING!Risk of injury from electric shock. Disconnect the
vehicle negative cable prior to Installation.
WARNING!Fire hazard due to short circuit: Secure your
vehicle with an additional fuse installed near the unit.
NOTE!Penetrating water can damage the unit: Prevent water from
entering the housing during cleaning.
NOTE!The unit is designed for interior use only. Do not mount the
unit outside the vehicle.
NOTE!Installation must only be carried out by qualified electricians.
Package contents
No. Name
1x CAN-LIN Gateway
1x Quick start guide
Accessories (optional)
CAN-LIN Gateway connection cable to LPS II
Part number 1601001136
Cable length: 5m
Connections: open cable end on M12 connector
Technical specifications
CAN-LIN Gateway
Part number 3001002027
Voltage range 9.8 V ... 14.6 VDC:
Temperature range -20 °C … +75 °C
Power consumption 18mA
Housing 7-pin relay socket housing
BUS system connections CAN bus/LIN bus
IP rating IP20
Protection class III
Weight 30g
Dimensions (LxWxH) 60 mm x 30 mm x 30 mm
LIN bus parameters
The following commands and information can be transmitted or
controlled via the LIN bus system:
Information Command
230 V AC input current Switch 230 V on/off
12 V DC input current
12 V DC output current
Solar power
Solar voltage
Battery temperature
Battery power
SoC (state of charge)
Output power in %
LEAB Automotive GmbH
Thorshammer 6
24866 Busdorf
Tel: [phone]
Fax: [phone]
[email protected]
It is prohibited to copy, duplicate, translate or otherwise
pass on the content of this document to third parties without
the express written permission of LEAB.
We make energy mobile.

PIN assignment
CAN-LIN Gateway
Pin Assignment Description
1 Terminal 31 Ground (earth)
2 CAN (High) CAN-Bus High
3 LIN LIN bus
4 Terminal 31 Ground
5 CAN (Low) CAN-Bus Low
6 n. a. Not assigned
8 Terminal 30 12 VDC:
M12 connector of the connection cable (accessories) PIN Assignment Description Core colour
1 Not assigned
2 Battery positive 12 VDC: Black
3 GND Ground Brown
4 CAN (High) CAN-Bus High Blue
5 CAN (Low) CAN-Bus Low Grey
Installation
WARNING!Risk of injury from electric shock. Disconnect the
vehicle negative cable prior to Installation.
To install the unit, proceed as follows:
NOTE!To ensure the smooth operation of the CAN-LIN Gateway,
make sure that the Gateway and the LPS II are at the same ground
potential (GND).
1. Connect pin2 (CAN (High)) to CAN (High) of the LPSII.
2. Connect pin5 (CAN (Low)) to CAN (Low) of the LPSII.
3. Connect pin3 (LIN) to the LIN connection point of the MBAC
(Mercedes-Benz Advanced Control).
4. Connect pin8 (12VDC) to the 12V connection point of your
vehicle or the LPSII.
5. Connect pin1 or pin4 (GND) to the ground of your vehicle or
the LPSII.
ðThe unit is installed.
Disposal
Dispose of the device in accordance with the Waste
Electrical and Electronic Equipment Regulations
(WEEE).
The system must not be disposed of with household
waste. Take it to a recycling point or return it to your
point of sale.
LEAB Automotive GmbH // Thorshammer 6 // 24866 Busdorf