LeapFrog LF80 Assembly Instructions

LF80
Audio Baby Monitor
Parent Guide
This guide contains important information.
Please keep it for future reference.
Visit our website leapfrog.com.au for more
information about products, downloads, resources
and more.
Scan the QR code
for more online
support:
Or go to leapfrog.com.au/support
Touch and learn!
Touch and learn!

2
19. This product should not be placed in any area where proper
ventilation is not provided. Slots and openings in the back or
bottom of this product are provided for ventilation. To protect
them from overheating, these openings must not be blocked
by placing the product on a soft surface such as a bed, sofa
or rug. This product should never be placed near or over a
radiator or heat source.
20. Never push objects of any kind into this product through
the slots because they may touch dangerous voltage points
or create a short circuit. Never spill liquid of any kind on the
product.
21. To reduce the risk of electric shock, do not disassemble
this product, but take it to an authorised service facility.
Disassembling or removing parts of the product other than
via the battery door may expose you to dangerous voltages
or other risks. Incorrect reassembling can cause electric shock
when the product is subsequently used.
22. You should test the sound reception every time you turn on the
units or move one of the components.
23. Periodically examine all components for damage.
24. There is a very low risk of privacy loss when using certain
electronic devices, such as baby monitors, cordless telephones,
etc. To protect your privacy, make sure the product has
never been used before purchase, reset the baby monitor
periodically by powering off and then powering on the units,
and power off the baby monitor if you are not intending to
use it for some time.
25. Children should be supervised to ensure that they do not play
with the product.
26. The small parts of this monitor can be swallowed by babies or
small children. Keep these parts out of reach of children.
27. The product is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of
the appliance by a person responsible for their safety.
SAVE THESE INSTRUCTIONS
Cautions
1. Use and store the product at a temperature between 0oC and
40oC.
2. Mishandling batteries can cause burn, fire or explosion hazards.
3. Do not expose the product to extreme cold, heat or direct
sunlight. Do not place the product close to a heating source.
4. Batteries should not be exposed to excessive heat such as bright
sunshine or fire.
5. Warning—Strangulation Hazard—Children
have STRANGLED in cords. Keep this cord out
of the reach of children. Do not remove warning
label on the adaptor cord.
6. Never place the Baby Unit(s) inside the baby’s cot or playpen.
Never cover the Baby Unit(s) or Parent Unit with anything such
as a towel or a blanket.
7. Other electronic products may cause interference with your baby
monitor. Try installing your baby monitor as far away from these
electronic devices as possible: wireless routers, radios, cellular
telephones, intercoms, room monitors, televisions, personal
computers, kitchen appliances and cordless telephones.
Important Safety Instructions
The applied name plate is located at the bottom of the Baby
Unit’s base. When using your equipment, basic safety precautions
should always be followed to reduce the risk of fire, electric shock
and injury, including the following:
1. Follow all warnings and instructions marked on the product.
2. Adult setup is required.
3. CAUTION: Do not install the Baby Unit at a height above 2
metres.
4. This product is intended as an aid. It is not a substitute for
responsible and proper adult supervision and should not be used
as such.
5. This product is not intended for use as a medical monitor.
6. Do not use this product near water, for example, near to a bath,
sink, swimming pool or shower.
7. CAUTION: Use only the battery provided. There may be a risk
of explosion if a wrong type of battery is used for the Parent
Unit. The battery cannot be subjected to high or low extreme
temperature and low air pressure at high altitude during use,
storage or transportation. Disposal of battery in fire or a hot
oven, mechanically crushing or cutting or the battery can
result in an explosion. Leaving the battery in an extremely high
temperature surrounding environment can result in an explosion
or the leakage of flammable liquid of gas. Battery subjected to
extremely low air pressure may result in an explosion or the
leakage of flammable liquid or gas. Dispose of used batteries
according to the instructions.
8. Use only the adaptors included with this product. Incorrect
adaptor polarity or voltage can seriously damage the product.
9. Use only the adaptors and battery listed below.
Power adaptor information:
VTech Telecommunications Ltd.
Model : VT05EAU06040
Rechargeable battery information:
1. GPI International Limited AAA 930mAH NiMH
(GNRHC103C000); 2. YIYANG CORUN BATTERY CO., LTD.
AAA 950mAH NiMH (Ni-MH AAA950)
10. The power adaptors are intended to be correctly oriented in a
vertical or floor mount position. The prongs are not designed to
hold the plug in place if it is plugged into a ceiling, under-the-
table or cabinet outlet.
11. For pluggable equipment, the socket-outlet shall be installed
near the equipment and shall be easily accessible.
12. Unplug this product from the wall outlet before cleaning.
13. Unplug the power cords before replacing batteries.
14. Do not use liquid or aerosol cleaners. Use a damp cloth for
cleaning. Do not modify the power adapters or replace with
other adaptors.
15. Do not allow anything to rest on the power cords. Do not install
this product where the cords may be walked on or crimped.
16. This product should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supply in your home, consult your dealer or
electricity supply provider.
17. Do not overload wall outlets or use an extension cord.
18. Do not place this product on an unstable table, shelf, stand or
other unstable surfaces.

3
What’s Included
Connect and Charge the Baby Monitor
1. Install Parent Unit Batteries
2
1
3
Notes:
• Only use and replace batteries with models listed in Important Safety Instructions (9).
• If the Baby Monitor is not intended to be used for long periods, disconnect and remove
the batteries to prevent possible leakage.
Parent Guide
Baby Unit
Parent Unit Accessories

4
Notes:
• Use only the power adaptors supplied with this
product.
• If your Baby Monitor is connected to a timer
controlled socket, make sure it is switched on.
• Connect the power adaptors in a vertical or floor
mount position only.
• Make sure Parent Unit, Baby Unit and the power
adaptor cords are out of reach of children.
2. Install Baby Unit Batteries
3. Connect the Baby Monitor
2
3
Strangulation
Hazard
Keepthis cordout of reach of children.
Thecordneeds to be at least three feet
awayfrom the child at all times. Do not
usewith an extension cord. Do not
removethis tag.
Éloignezce cordondes enfants. Le
cordondoit se trouveràau moins trois
piedsd’un enfant et ce,en tout temps.
N’utilisezpas de rallonge.Neretirez pas
cetteétiquette.
Mantengaeste cable fuera dela alcance
delosniños. Este cable debe estar por
lomenostres pies fuera de la alcance
delniño en todo momento. No lo use
conuna extensión inalámbrica. No quite
estaetiqueta.
Risque
d’étranglement
Riesgo de
estrangulación
Strangulation
Hazard
Keepthis cordout of reach of children.
Thecordneeds to be at least three feet
awayfrom the child at all times. Donot
usewith an extension cord. Do not
removethis tag.
Éloignezce cordondes enfants. Le
cordondoit se trouveràau moins trois
piedsd’un enfant et ce,en tout temps.
N’utilisezpas de rallonge.Neretirez pas
cetteétiquette.
Mantengaeste cable fuera de la alcance
delosniños. Este cable debe estar por
lomenostres pies fuera de la alcance
delniño en todo momento. No lo use
conuna extensión inalámbrica. No quite
estaetiqueta.
Risque
d’étranglement
Riesgo de
estrangulación
1

5
4. Charge the Baby Monitor
When you have connected and turned on the Parent Unit and Baby Unit, the batteries will
charge automatically.
Battery Indicators Battery Status Action
The unit beeps and the
screen displays .
The battery is low in power and
may only be used for a short time.
Charge without
interruption (about 30
minutes).
The battery icon
becomes solid . The battery is fully charged.
To keep the battery
charged, connect it to AC
power when in use.
The battery icon on the screen indicates the battery status:
Notes:
• Before using the Baby Monitor for the first time, charge the Parent Unit and Baby Unit
batteries for 12 hours.
• The standby time varies depending on the sensitivity level you set, your actual usage, and the
age of the batteries.
5. Power On or Off the Baby Monitor
1. Press and hold to power on or power
off Baby Unit.
2. Press and hold to power on or power
off Parent Unit.

6
Position the Baby Monitor
Caution:
• The default speaker volume of your
Parent Unit is level 3. If you experience
feedback from your baby monitor while
positioning:
- Make sure your Baby Unit and Parent
Unit are more than 2 metres apart, OR
- Turn down the volume of Parent Unit.
Notes:
• To avoid interference from other electronic
devices, place your baby monitor at least 1
metre away from devices such as wireless
routers, microwaves, mobile phones and
computers.
<2 m
>2 m
2
>2 m
3
≥
<
1 m
1 m
NOT LINKED
4
>1 m
1
Change the Faceplate
1
2
3
Install 1
2
3
Detach

7
4
5
6
3
1
2
7
8
9
10
11
12
13
14
1Night light
• On when night light is turned on manually.
• Off when night light is turned off manually.
2Changeable face plate
3POWER light
• On when Baby Unit is powered on.
• Off when Baby Unit is turned off.
4Battery indication light
• On when Baby Unit’s batteries are charging.
• Flashes when the batteries are low and
need charging.
5
• Press to play the next lullaby.
• Press and hold to record your own voice for
up to 20 seconds. Release when finished
recording. The recorded voice will be saved
as SONG 5.
6Microphone
7
• Press to increase the speaker volume (Level
1 to Level 5).
8
• Press to turn the night light on or off.
• Press and hold to adjust the brightness of the
night light.
9
• Press and hold to power on, and the power light
turns on.
• Press and hold to power off, and the power light
turns off.
• When Baby Unit is powered on, press to play the
selected lullaby or the recorded voice. Press again
to stop playing.
10
• Press to decrease the speaker volume (Level 1 to
Level 5).
11 Belt clip with temperature sensor
12 Speaker
13 Power jack
14 Battery compartment cover
Baby Unit Overview

8
13- level sound indicator light
• Green when low sound level is detected by Baby
Unit.
• Green and amber when moderate sound level is
detected by Baby Unit.
• Green, amber and red when high sound level is
detected by Baby Unit (e.g. baby crying loudly).
2LCD display
3Changeable face plate
4
• Press to increase the speaker volume (Level 1
to Level 5).
• While in a menu, press to scroll up.
5Battery indication light
• On when the Parent Unit’s batteries are
charging.
• Flashes when the batteries are low and need
charging.
6
• Press and hold to talk to your baby.
7
• Press and hold to power on and power off
Parent Unit.
• While in a menu, press to return to the previ-
ous menu.
8Microphone
9
• When in idle mode, press to set the alarm
timer.
• When setting the alarm timer, press to exit.
10
• Press to enter the main menu.
• While in a menu, press to choose an item, or
save a setting.
• When setting the alarm timer, press to exit.
11
• Press to play or stop playing the lullaby or re-
corded voice.
• When setting the alarm timer, press to reset the
timer.
12
• Press to decrease the speaker volume (Level 1
to Level 5).
• Press repeatedly until the volume reaches the
minimum to turn it off.
• While in a menu, press to scroll down.
13 Speaker
14 Belt clip
15 Power jack
16 Battery compartment cover
Parent Unit Overview
11
12
4
5
2
6
2
1
7
8
9
10
313
14
15
16

9
To keep this product working well and looking good, follow these guidelines:
• Avoid placing it near heating appliances and devices that generate electrical noise (for example, motors or fluorescent lamps).
• DO NOT expose it to direct sunlight or moisture.
• Avoid dropping the product or treating it roughly.
• Clean with a soft damp cloth.
• DO NOT immerse the Parent Unit and the Baby Unit in water and do not clean them under running water.
• DO NOT use cleaning spray or liquid cleaners.
• Make sure the Parent Unit and the Baby Unit are dry before you connect them to the mains again.
General Product Care
Disposal of Batteries and Product
The crossed-out wheelie bin symbols on products and batteries, or on their respective packaging, indicates they must not
be disposed of in domestic waste as they contain substances that can be damaging to the environment and human health.
The chemical symbols Hg, Cd or Pb, where marked, indicate that the battery contains more than the specified value of
mercury (Hg), cadmium (Cd) or lead (Pn) set out in Battery Directive (2006/66/EC).
The solid bar indicates that the product was placed on the market after 13th August, 2005.
Help protect the environment by disposing of your product or batteries responsibly.
Customer Service and Product Warranty
IMPORTANT
Please retain this booklet with your sales receipt as proof of the date of purchase.
Customer Service
If you require assistance in operating this product, please call the TecHelp Information Line on
1300 369 193 or contact VTech by e-mail at: [e-mail].
Voluntary Product Enquiry
In addition to your Statutory Rights and subject to the conditions below, VTech warrants that this product will be free from any defect in materials or
workmanship under conditions of normal use for a period of 24 months from date of purchase.
VTech does not warrant that the product will be free from defects if defects are caused by an accident, misuse, abuse, improper installation or operation,
vermin infestations, lack of reasonable care, unauthorised modification, loss of parts, tampering or attempted repair by a person not authorised by VTech;
or where the product has been damaged by lightning or a mains power surge.To make a claim under this Voluntary Product Warranty you must call the
TecHelp Information Line on 1300 369 193 or contact VTech by e-mail at: [e-mail] where a Customer Service Representative will
inform you of the product return process. You will need to ensure that:
• You provide proof of purchase;
• Your product is suitably packaged (original packaging is not required); and
• You have included all components from the original purchase.
For your records
Date of purchase:
Place of purchase:
Serial number:
For Voluntary Product Warranty purposes, proof of purchase is required so please keep your receipt.
The benefits conferred by this Voluntary Product Warranty are in addition to other rights and remedies that are available to you under law, which cannot
be excluded. The processes for this Voluntary Product Warranty in no way limit your rights which arise as a result of your Statutory Rights.
This Voluntary Product Warranty is given by:
VTech Telecommunications (Australia) Pty Ltd ABN 70 136 672 627
Address: 24 Gilby Road, Mount Waverley 3149
IMPORTANT NOTE: THIS IS NOT A PRODUCT RETURN OR SERVICE ADDRESS – PLEASE CONTACT TECHELP BY PHONE OR EMAIL FOR PRODUCT
AND WARRANTY SUPPORT. NO LIABILITY WILL BE ACCEPTED BY VTECH FOR PRODUCTS RETURNED TO THIS ADDRESS UNDER THIS VOLUNTARY
PRODUCT WARRANTY.
Phone number: 1300 369 193
Email address: [e-mail]
Statutory Rights
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major
failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail
to be of acceptable quality and the failure does not amount to a major failure.

10
Customer Support
Find the answer to your questions. Get assisted at your
own pace using our knowledge-rich full Online Manual, or
contact Customer Support with your inquiries.
Scan the QR code to access the Online Support
Page or visit leapfrog.com.au/support.
Technical Specifications
Specifications are subject to change without notice.
© 2023 LeapFrog Enterprises, Inc.
a subsidiary of VTech Holdings Limited.
All rights reserved. 09/23. LF80-X_AU_QSG_V1.
Frequency control Crystal controlled PLL synthesizer
Transmit
frequency
Baby Unit: 1881.792 - 1897.344 MHz
Parent Unit: 1881.792 - 1897.344 MHz
Maximum power used by the transmitter: 0.25 W (250 mW)
Channels 10
Power
requirements
Baby Unit / Parent Unit: 1.2 V AAA 930 / AAA 950 mAh Ni-MH battery
Baby Unit / Parent Unit power adaptors:
Output: 6 V DC 400 mA