LED Technologies DPL II User manual

USER GUIDE & OPERATING INSTRUCTIONS
Includes important safety information. Read all instruction
before using device. Save these instructions.
PANEL SYSTEM
Anti-Aging
cleared

Important Safeguards
System Includes
Precautions
- Do not operate device where it could come into
contact with water.
- Do not use the device if Power Supply has fallen
into water or is damaged in any way.
- Stop using device immediately if you think it is
defective. Please contact LED
Technologies immediately.
- Do not bend or abuse the wire of the Power
Supply as this can cause electrical
shock and problems.
- Do not attempt to take the device apart. The
device is not serviceable by the user.
This will void the warranty.
- Always unplug Power Supply from wall outlet
when not in use.
- Do not store device in sun or location with high
temperatures as this may cause
damage to plastic casing.
- Use only the supplied Power Supply.
Professional Panel Device
Adjustable Stand
Travel Bag
110v Power Supply
Goggles

Cautions
- Do not use this device on infants and young
children without physician approval.
- Do not shine the device lights directly into
the eyes.
- Discontinue use if device overheats or becomes
uncomfortably hot to your skin.
- Do not use this device if your skin is light sensitive
or you are currently using medication
that may cause skin sensititvity to light.
- Do contact your Doctor prior to using if you:
• Are pregnant or suspect you may be pregnant.
• Taking drugs known to cause light sensitivity.
• Have any suspicious or cancerous lesions.
- Contact your Doctor if you have any
medical questions regarding use
of this device.
- Contact your Doctor if you suspect that you have
had a negative reaction from using
this device.

Anti-aging Treatment
Assembly Instructions
This is a Medical Grade light emitting diode (LED) device that
emits energy for the use in dermatology for the treatment of
ne lines and wrinkles, skin pigmentation and overall skin tone
through IR, Deep Red, Red and Amber lights. The device
treatment time is controlled by the operator. There are no user
settings or adjustments.
1. Unpack your DPL®II device.
2. Plug Power Supply into device.
3. Plug Power Supply into wall outlet.
4. Press Power Button to turn on and off.
Light Sensitivity Test
Test yourself for light sensitivity prior to using on your face:
1. Power on your device.
2. Place device on or within ¼” of the skin on
your forearm for three minutes.
3. After 3 minutes check the area. If area has turned red
and lasts for more than 2 hours your skin is light sensitive.
4. Discontinue use and contact Customer Service.

Operating Instructions
1. Wash and clean area prior to use and pretreat area
with Serums for maximum benet.
2. Attach Power Supply
3. Plug the Power Supply into wall outlet.
4. Press power button for anti-aging and recovery.
5. Place the device as close to the skin as possible for the
desired treatment area.
6. Leave the light on the treatment area for a minimum of 8
minutes. For recovery treatments longer sessions
are recommended.
7. The device will beep every minute to alert user to
treament time.
8. Move device to the next treatment area and
repeat steps 4-7.
9. Shut off device and store in travel bag.
10. Use the device daily for best results.
11. Unit will automatically shut off if the device exceeds
desired temperature. Let unit cool for a few minutes
and begin treatments again.
12. Do not obstruct or block ventilation holes
during operation.

Cleaning & Maintenance
Maintenance:
1. This is a medical device, it is important to keep it clean.
2. There are no “user” serviceable parts in this device.
3. The device includes only an On/Off switch: all settings
are set at the factory.
4. Use only supplied Power Supply.
Cleaning:
1. Turn device off and unplug from any power source.
2. Do not clean the LED lights with any liquid or damp cloth.
Use air blower device like a blow dryer or computer air
cleaner to remove particles and dust from LEDs.
3. Clean device exterior with damp cloth or
rubbing alchol.
4. Allow to dry completely prior to use.
Troubleshooting
1. System not turning on:
a. Is power cord pushed rmly into outlet?
b. Try a different wall outlet to conrm
power is available.
c. Is power cord pushed rmly into panel?
d. Is On/Off button turned on?
e. If device still does not turn on call Customer Service.
2. System shuts off automatically:
a. If the device gets too hot it is designed to shut off
automatically to avoid damage to electrical parts
b. Make sure ventilation holes on back are not covered or
blocked.
c. Allow device to cool down for several minutes, then
attempt to turn device on again.
d. If device continues to shut down please contact
Customer Service.

Traveling with device outside the
United States
Customer Service
Disclaimer
The Power Supply is designed for USA standard 110V power
outlets. When traveling outside the USA, you will need to check
the local power requirements and use the appropriate power
adapter and/or converter.
You can reach Customer Service by calling
1(800) 337-9565, Monday-Friday 8:00am-5:00pm, Mountain
Standard Time. Customer Service can also be reached by
email at, [email protected].
This product is not intended to diagnose, cure or prevent
disease. LED Technologies makes no claims, representations or
warranties regarding the ability of this product to cure any
physical, skin or mental condition. A qualied health professional
should be consulted with regard to any condition requiring
medical attention.
The following lost or damaged parts can be purchased as
replacement items directly from LED Technologies by calling
Customer Service at 1 [phone]
1. Power Supply
2. Adjustable Stand
3. Goggles
4. Travel Bag
Replacement Parts

As a valued customer, when you register your device at
www.ledtechnologies.com you will automatically be kept informed and
be able to participate in exclusive offers, VIP discounts, new product
previews as well as the opportunity to earn free products through new
product trials.
Stay Connected
Warranty
LED Technologies, warrants that this product will be free from defects in
materials and workmanship for 1 year from the date of purchase by the
original owner. This warranty covers the original purchaser only and is not
assignable or transferable to another party. Register your warranty by
calling Customer Service at 1(800) 337-9565