LED World LT-995 DMX/RDM User manual

LT-995 DMX/RDM Decoder Manual
PRODUCT SPECIFICATIONS
Power Supply
Input Voltage
Max Current Load
Max Output Power
Photoelectric Isolation
Grey Level
Protection
Output DMX Channel
DMX512 Socket
Working Temperature
Dimension
Weight (G.W)
DC Constant Voltage Class 2
DC 12V~DC 24V (Use only with Class 2 regulated Power supply)
6A x 5CH (Max. 30A)
(0~72W...144W) x 5CH (Max. 720W)
Yes
8 bit (256 levels) / 16 bit (65536 levels)
Short circuit/ Over temperature / Over current protection, Automatic recovery
5 CH/RDM
XLR-3, Rj45, Green Terminal
-30°C ~ 50°C (-22°F ~ 122°F)
L 169 x W 80 x H 39 mm (6.65” x 3.14” x 1.53”)
1.21 lb
This product is intended to be installed and serviced by a qualied licensed electrician. Install in accordance with the National Electric Code, and
local regulations. Disconnect power before installing or servicing. Only power with a regulated (listed) constant voltage Class 2 power
supply (12-24V DC).
Ensure applicable wire is installed between driver, xture and any controls in between. When choosing wire, factor in voltage drop, amperage
rating and type (in-wall rated, wet location rated, etc.). Inadequate wire installation could overheat wires and cause re.
This product is rated for indoor installation and only for dry locations. Avoid direct sun light.
Do not modify this product beyond the instructions in this guide or the warranty will be voided.
Wiring diagrams in this installation guide for basic installations. Please carefully review your installation before proceeding
SAFETY & WARNINGS
BEFORE YOU BEGIN, READ ALL WARNINGS AND INSTALLATION INSTRUCTIONS AND SAVE FOR FUTURE USE.
1/4 Copyright © 2019 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 1.0 12/02/19
1-800-387-4081
ledworldlighting.com ledworld.ca |
PRODUCT FEATURES
·5 output channels, Max 6A per channel. Up to 720W output
·Easy operation with digital display and the touch buttons.
·3-pin XLR, Rj45 and Terminal DMX ports connectivity
·With RDM remote management protocol, the operations can be
completed via RDM master console such as parameters browsing and
setting, DMX address setting and equipment recognition
·Short circuit, Over temperature and Over current protection
·Self testing function
·Optional High/Low PWM frequency
·Optional 16bit (65536 levels) / 8bit (256 levels) grey level
·Firmware upgrade function

1-800-387-4081
ledworldlighting.com ledworld.ca |
2/4
PRODUCT COMPONENTS
006
M
^
^
006
M
^
^
Digital
Display Dip
Switch
Green Terminal
DMX/RDM
input & output
3-pin XLR
DMX/RDM
input & output
Rj45
DMX/RDM
input & output
Digital Display
Dip Switch
ŸDigital display will be locked mode
after 15 seconds of inactivity
ŸLong press “M” key to unlock the
display.
ŸShort press “M” key to switch
between 3 digits.
ŸPress “^” ”v” key to adjust digit
value.
ON CHA
1 2 3 4
Bit
16
8
PWM Hz
High
Low
DIM
Smooth
Std
Screen
30s off
Enable
1 2 3 4
PRODUCT DIMENSION
Note: Keep Dip Switchs at the bottom for
best performance of decoder
LT-995 DMX/RDM Decoder Manual
Copyright © 2019 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 1.0 12/02/19
+
+
+
+
12/24VDC
input
LED xture
output
169mm (6.65”)
157mm (6.18”)
39mm (1.53”)
80mm (3.14”)
59mm (2.32”)

Warning: Input voltage must be identical to output voltage of the LED Fixture!
Exposed wire should not be more than 6- 8 mm long & solder tip (tinned). Do not allow Wires to cross and insure all exposed wire is fully
inserted into the screw terminals. Hand tighten screw terminals. Use 16 to 12 AWG wire for output terminals.
ŸInput Voltage must be identical to output voltage of the LED
ŸInput: For low voltage power input (12DC ~ 24VDC). V- and V+. Use only 16 to 12 AWG wire for input terminals.
WIRE 6-8 MM (0.25-0.30")
LT-955 WIRING DIAGRAM
1-800-387-4081
ledworldlighting.com ledworld.ca |
3/4
LT-995 DMX/RDM Decoder Manual
Copyright © 2019 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 1.0 12/02/19
DMX Data
Output
Class 2 Low Voltage Driver *
DMX Master Controller
RGB Strip Light / Fixture
Wall Washer / DMX-512 Fixture
AC Power
50/60Hz
RJ45 / XLR-3
RJ45 Splice Cable
Wiring Connections
Brown Ground
White/Orange Data +
Orange Data -
R
G
B
D- GNDGND D+Vin
Channel Color
Channel 1 - Red
Channel 2 - Green
Channel 3 - Blue
Channel 4 - White
AC Power
50/60Hz
G
N
L
V+
V-
White/Green VDC - (GND)
White/Blue VDC + (Vin)
CAT5 ( Rated For Inside Wall use)
DMX IN
DMX OUT
DMX IN
V+
Ch1
Ch2
Ch3
Ch4
D+
D-
Data +
Data -
Ground
LT-995
Class 2 power input
Adapter Connector
DMX Signal
+-
Make sure that
wires cannot
cross
+-
Make sure that
wires are screwed tight
and fully inserted
wrong correct
Warning
L
N
AC Power
50/60Hz
Class 2 Low Voltage Driver
G
N
L
t
u
p
n
I
t
u
p
t
u
O
V+
V-
Max 500mA
D- GNDGND D+Vin
Orange
White/Orange
Brown
VDC
VDC
Power In DMX Data Out
_+
Ch5
V+
D+
D-
DMX AMP
Data +
Data -
Ground
Class 2 Low Voltage Driver *
RGBW Strip Light / Fixture
R
G
B
AC Power
50/60Hz
G
N
L
V+
V-
DMX IN
DMX OUT
DMX IN
V+
Ch1
Ch2
Ch3
Ch4
D+
D-
Data +
Data -
Ground
LT-995 Ch5
V+
D+
D-
DMX AMP
Data +
Data -
Ground
W
Channel 5 - Optional Extra White

WARRANTY
This product comes with 2 years ltd warranty, lifelong technical maintenance. The warranty excludes improper connection to power supply, power
overload, manual damages and improper use. Repair or replacement as provided under this warranty is exclusive remedy of the customer. We shall
not be liable for any incidental or consequential damages for bench of any stipulation in this warranty.
LOW VOLTAGE INPUT
Input power to the DC+ and DC- with Class 2 regulated (low voltage) power source. Verify that the power supply is a regulated Class
2 power supply.
If attaching RGB Flex Strip to LT-995 DMX512, correct polarity is imperative; Black (or White) wire is positive (+) and goes to “V+” terminal. The
common format is to insert the Red wire to Ch1, Green wire to Ch2 and Blue wire to Ch3. If unit is set to DMX Channel1, the unit will automatically
occupy channels 1,2,3 and 4 on the master DMX console. Ch4 is for single color LED Flex Strip or white in RGBW strip.
If attaching a single color, the format is to attach the positive to V+ and negative to Ch1 (but can also be Channel 2,3,4 or 5) for standard
congurations of RGB.
1-800-387-4081
ledworldlighting.com ledworld.ca |
4/4
LT-995 DMX/RDM Decoder Manual
Copyright © 2019 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 1.0 12/02/19