Ledix Zamel ZNP-02-14 User manual

www.ledix.pl
14 V DC / 2 W
junction box power supply
ZNP-02-14
230 V AC
Zamel Sp. z o.o.
PL 43-200 Pszczyna, ul. Zielona 27, Poland
tel: [phone], fax: [phone]
e-mail: [email protected], www.ledix.pl
230 V AC / 2 W IP20
weight: 30 g
PN-EN 61204-3
PN-EN 55022
PN-EN 61000
Declaration of Conformity is on www.ledix.pl
14 V DC / 2 W junction box power supply
ZNP-02-14
The symbol means selective collecting of electrical and electronic equipment.
It is forbidden to put the used equipment together with other waste.
ZNP-02-14 junction box power supply is a professional impulse power supply with 14 V DC
output voltage and 2W nominal power. The power supply is designed to cooperate with
LEDIX products (lighting ttings, controllers, radio receivers) supplied with 14 V DC. It is de-
signed for a direct mounting in a junction box.
Characteristic features:
• 14 V DC nominal output voltage, 2 W nominal power,
• low power consumption in the standby mode (0,25 W),
• efficiency at the level of 79%,
• high stability of the output voltage with input voltage or load changes.
The power supply cooperates with:
• LEDIX series LED diode fittings supplied with 14 V DC
• LED controllers and radio receivers supplied with 10÷14 V DC.
CAUTION: The total power of lighting fittings or of the devices cooperating with the
power supply must not exceed 2 W.
Mounting in a Ø60
junction box
Mounting
indoor only
14 V DC
output voltage
ZNP-02-14 ENG Ver. 01
SCAN
the technical
data

47,5 20
47,5
230 V AC
14 V DC
LEDIX series
lighting tting
10 ÷ 14 V DC
CAUTION !The device is designed for single-phase installation and must be installed
in accordance with standards valid in a particular country. Installation, connection
and control should be carried out by a qualied electrician sta, who act in accord-
ance with the service manual and the device functions.
1. Disconnect power supply by the phase fuse, the circuit-breaker or the switch- discon-
nector combined to the proper circuit.
2. Check if there is no voltage on connection cables by means of a special measure equip-
ment.
3. Connect the output cables in accordance with the connection diagram.
4. Mount the ZNP-02-14 in the Ø60 junction box.
5. Switch on the power supply from the mains.
•When connecting ttings or devices to ZNP-02-14 power supply pay attention to
a correct polarity of the output cables.
•Total power capacity can not exceed the nominal power of the power supply.
ZNP-02-14 power supply is a professional impulse power supply with 14 V DC output volt-
age and 2 W nominal power. The power supply is designed to supply the LEDIX series
ttings and LEDIX devices such as radio controllers, radio receivers, RGB ampliers, etc.
It is designed for a direct mounting in a junction box. The device has a short-circuit and
overload protections, which increase the safety of its use. Its high eciency and a very low
power consumption in the standby mode makes it a very economical solution, designed
for continuous operation. The power supply meets the requirements of the harmonised
standards. The features of the power supply:
• 14 V DC nominal output voltage, 2 W nominal power,
• small dimensions - suitable for mounting in a typical Ø60 junction box,
• low power consumption in the standby mode (0,25 W),
• eciency at the level of 79%,
• high stability of the output voltage with input voltage or load changes,
• protections: short-circuit, overload,
• wide ambient temperature range: -10 ÷ +50 oC,
• long-term operation reliability,
• terminal connection.
TECHNICAL DATA
MOUNTING
DESCRIPTION
DIAGRAM
DIMENSIONS FAMILY OF PRODUCTS
Nominal output voltage: 14 V DC
Nominal output current: 0,14 A
Nominal output power: 2 W
Output voltage tolerance: 5%
Output voltage ripples: 80 mVPP
Output voltage time increase: 10 ms
Output voltage time adjustment: 20 ms
Nominal input voltage: 230 V AC
Input voltage tolerance: -10 ÷ 15%
Nominal frequency: 50 Hz
Eciency: 79 ÷ 80%
Power consumption (standby): 0,25 W
Starting current: 20 A
Protections: short-circuit, overload
Ambient temperature range: -10 ÷ +50 oC
Mounting: In a Ø60 junction box
Casing protection degree: IP20
Protection class: II
Dimensions: 47,5 x 47,5 x 20 mm
Weight: 30 g
Reference standard: PN-EN 61204-3; PN-EN 55022; PN-EN 61000
ZNP-XX-XX
Nominal
output power:
2 – 2 W
8 – 8 W
15 – 15 W
Nominal
output voltage:
12 – 12 V
14 – 14 V
Symbol (series)