LEDS C4 71-7667-00-00 User manual

71-7667-00-00 — Remote Control RF/RGB
—Function introduction
Front side
←
Important: Read All Instructions Prior to Installation
Indicator: indicate the
state of remote control
Press and hold down to increase
light intensity of RGB channels
Press and hold down to
increase/decrease light
intensity
Click to turn ON/OFF all zones
Click to return to previous
status
Press and hold down to speed
down under dynamic mode
Press and hold down to save
colors/scenes;click to recall
the saved colors/scenes
Press and hold down to speed up
under dynamic mode
Press and hold down to decrease
light intensity of RGB channels
Play/Pause button, click to
play/pause 10 built-in modes
RGB channels, click to turn off/on
the channel, Press and hold down to
increase/decrease light intensity of
R/G/B channel
Zone numbers: click to choose the
zone/zones, Press and hold to turn
on/off corresponding zone
White channel: the 4th channel
Click to turn on/off, Press and hold
down to increase/decrease light
intensity of the channel
LEDS C4 S.A. - Afores s/n 25750 Torà. Lleida (Spain). [phone] leds-c4.com
Bottom side
3xAAA battery
←
• This device contains AAA batteries that shall be stored and disposed properly.
• DO NOT expose the device to moisture.
—Operation
—Safety & Warnings
Step 1: Do wiring the RF receiver according to wiring diagram (please refer to the
instruction of RF receiver that you would like to pair with).
Step 2: Click ON/OFF button to activate the remote.
Step 3: Click the “Learning key” button on RF receiver.
Step 4: Choose and click a zone number (e.g. zone 1).
Step 5: Touch the color wheel, LED lights connected with the RF receiver flicker
once means the receiver is paired with zone 1 successfully.
—Product Data
Output RF signal
Operation Frequency 869.5/916.5/434MHz
Power Supply 4.5V (3xAAA battery)
Operating temperature 0-40˚ C
Relative humidity 8% to 80%
Dimensions 140 × 48 × 17 mm
Waterproof grade IP20
• Control 6 zones of RF receivers separately.
• RGBW color controller.
• High sensitive & high stable fast & precise color
control.
• Compatible with RF receivers.
• 1 receiver can be paired by max 8 different
remote controls.
Pair with RF receiver (Method 1)
x1 Learning key RF/RGB
RECEIVER
5 x1
2x1
4 x1

LEDS C4 S.A. - Afores s/n 25750 Torà. Lleida (Spain). [phone] leds-c4.com
Step 1: Click ON/OFF button to activate the remote.
Step 2: Choose and click one or multiple paired zone numbers (e.g. zone 1).
Step 3: Touch the color wheel or click the other buttons to select the scene
you like.
Step 4: Press and hold down button S until the LED indicator of remote flash
once
Step 5: Immediately click any number of 1-6 (e.g. 1) (here the numbers mean
6 scenes can be saved for the selected zone), LED lights connected with the
RF receiver flicker once means the color/scene was saved successfully.
Save color/scene/mode
3 x1
1 x1
4 x1
2 x1
5 x1
Step 1: Click ON/OFF button to activate the remote.
Step 2: Choose and click one or multiple paired zone numbers (e.g. zone 3).
Step 3: Click button S
Step 4: Click any numbers 1-6 (e.g. 1) (here the numbers mean 6 scenes
saved for selected zone) to recall the saved scene.
Buit-in 10 color changing modes are as follows:
Mode 1: Any two colors of RGB mix fade-in & fade-out.
Mode 2: RGB three colors mix fade-in & fade-out.
Mode 3: RGB three colors mix fade-out & fade-in.
Mode 4: RGB flash.
Mode 5: RGB three colors fade-in & fade-out successively.
Mode 6: RGB three colors fade-in successively.
Mode 7: RGB three colors fade-out successively.
Mode 8: RGB three colors jump changing successively.
Mode 9: R&B two colors mix fade (R in B out), then G fade-in, then R&B mix fade (R out B in), then G fade-out.
Mode 10: B fade-out, then G&B mix fade (G out B in), the R&G mix fade (R out G in), then R fade-in.
Recall the saved colors/scene
1 x1
3 x1
4 x1
2 x1