MELICONI GUMBODY UNIVERSAL 3-300 User manual

1
USING THE KEYS AND FUNCTIONS
The functions described below are only available
if they are already foreseen by your TV.
Keep this booklet in case you ever need to consult us in the future.
Thanks to the enclosed CD and to the on-line guide on the site www.meliconi.com/guide
it is even easier and faster to programme the remote control and discover
all the potential offered by the UNIVERSAL 3-300.
PREPARE FOR USE
Read these instructions carefully before programming your remote control!
Thanks to its large database and numerous functions the UNIVERSAL 3-300 remote control is ideal for
replacing up to 3 remote controls of any brands for TV - DVD/CR (
Video Recorder ) SAT/TER ( Digital Terrestrial ).
Its ergonomic form and casing in soft rubber make it easy to grip and protect it against falls and bumps.
Thank you for choosing a MELICONI remote control.
UNIVERSAL 3-300
Keys for selecting which appliance
you want to use.
They light up whenever a command
is sent to the selected appliance.
Teletext keys
ON/OFF key to turn the selected
appliance on and off
Keys that the user can customize
to memorize and access
additional commands
Confirm key
To move around within
the MENU or to control
the BRIGHTNESS/COLOUR
VCR/DVD function keys:
RECORD - PAUSE - STOP - PLAY
or fastext functions
Specific area for SET TOP BOX
To select the next (P+) or
previous (P-) channel or programme
Control the volume using +/–
MUTE
turns the volume on and off
FORWARD / REWIND
functions for VCR and DVD
Number keys
To select an external input terminal
GB

1. Turn on the appliance to be programmed:
- if a VCR, insert a cassette
- if a SAT or TER select a programme
- if a DVD insert a DVD.
2. Look in the Code Book for the brand of the appliance to
be programmed and make a note of the corresponding
code indicated alongside
(e.g. PHILIPS 0025) .
3. Hold down the selection key for the appliance to be
programmed for 5 seconds.
4. When the key is released, it will start to flash. Enter the
brand code previously identified (
e.g. 0025 ). The selection
key flashes more quickly to indicate that the remote control
is ready for the search.
5. Point the remote control at the appliance. Press and slowly
release the ON/OFF key or PLAY for the VCR and DVD
several times, stopping when the appliance responds
correctly to the command.
6. When the appliance responds correctly, press OK to
confirm. Three flashes indicate that the search operation
has been completed correctly.
2
HOW TO PROGRAMME THE REMOTE CONTROL
FITTING THE BATTERIES
Before programming and using the remote control,
fit the batteries.
The remote control requires 2 new AAA/LR03 batteries. Insert the batteries as shown:
• Change the batteries if the light indicator starts to flash
during use. The batteries are low.
• Make a note of the codes for your appliances on the
adhesive label inside the battery cover in case you have
to reprogramme your remote control.
• This remote control has a permanent memory and does
not lose the programmed codes or functions when the
batteries are removed.
To display and make a note of the code memorized by means of the search,
follow the instructions described in the paragraph CURRENT CODE DISPLAY.
ADDITIONAL CHECK
Check that some of the other functions used on your original remote control are working correctly. If the
commands function incorrectly or erratically, you have probably entered a code for a similar remote control
but not the right one. In this case, repeat the search procedure starting from point 3, entering the code
previously used (e.g. 0025).
PHILIPS 0025
The TV - DVD - SAT keys can be programmed according to your
requirements, following the procedure described below.
The quickest and easiest way to programme the remote control is
by consulting enclosed CD or the website www.meliconi.com/guide.
Warning: programme one appliance at a time!
+++
5 SEC.
or
or
or

N.B. THE LIGHT INDICATOR STOPS FLASHING.
The remote control exits programming mode and the light indicator stops flashing:
• if no keys are pressed for 14 seconds
• if an invalid brand code is entered
• if a key other than ON/OFF or PLAY is accidentally pressed
• if the end of the code search list has been reached. In this case consult the enclosed CD or the site
www.meliconi.com/guide
GLOBAL SEARCH REMOTE CONTROL PROGRAMMING
The quickest and easiest way to programme the remote control is
by consulting enclosed CD or the website www.meliconi.com/guide.
Warning: programme one appliance at a time!
1. Turn on the appliance to be programmed:
- if a VCR, insert a cassette
- if a SAT or TER select a programme
- if a DVD insert a DVD.
2. Hold down the selection key for the appliance to be
programmed for 5 seconds.
3. When the key is released, it will start to flash. Enter the
code 0000; the selection key flashes more quickly to
indicate that the remote control is ready for the search.
4. Point the remote control at the appliance. Press and slowly
release the ON/OFF key or PLAY for the VCR and DVD
several times, stopping when the appliance responds
correctly to the command.
5. When the appliance responds correctly, press OK to
confirm. Three flashes indicate that the search operation
has been completed correctly.
ADDITIONAL CHECK
Check that some of the other functions used on your original remote control are working correctly. If the
commands function incorrectly or erratically, you have probably entered a code for a similar remote control
but not the right one. In this case, repeat the search procedure starting from point 2.
To display and make a note of the code memorized by means of the search,
follow the instructions described in the paragraph CURRENT CODE DISPLAY.
N.B. THE LIGHT INDICATOR STOPS FLASHING.
The remote control exits programming mode and the light indicator stops flashing:
• if no keys are pressed for 14 seconds
• if a key other than ON/OFF or PLAY is accidentally pressed
• if the end of the code search list has been reached. In this case consult the enclosed CD or the internet site
www.meliconi.com/guide
3
This operation can take up to 20 minutes and should be carried out if you have not succeeded in programming
the remote control by means of the method described above.
+++
5 SEC.
or
or
or

1. Hold down the selection key for the appliance to be
programmed for 5 seconds.
2. When released, the selected key will start to flash, enter
the code (
e.g. TV 1100 ). Three flashes indicate that the
operation has been completed correctly.
CURRENT CODE DISPLAY
N.B. this operation cannot be interrupted and the remote control cannot
therefore be used until the end of the 4 series of flashes.
1. Hold down the selection key of the appliance whose code
you want to know for 5 seconds.
2.
When the key is released it will start to flash; press and
release the 1-/-- key within 8 seconds .
3. After a few seconds, the light indicator communicates
the code you are looking for by flashing the four numbers
separately. Count the number of flashes; each series of
flashes corresponds to one figure in the code. 10 flashes
correspond to 0.
4. Make a note of the code on the adhesive label inside
the battery cover for quick and easy future reprogram-
ming.
To find out the code of your remote control, follow this procedure:
Although not indicated on the keypad,
some keys can be used for additional commands.
Find them on your UNIVERSAL 3-300 remote control by pressing the keys one by one and discovering the
commands that interest you.
In particular, the additional functions most frequently used, such as NORMALIZATION, COLOUR and
BRIGHTNESS, can be found on the following keys:
TV FUNCTIONS ALWAYS ACTIVE
HOW TO USE THE ADDITIONAL COMMANDS WHICH DO NOT APPEAR ON THE KEYPAD
For the functions used less frequently, look for the additional commands on the enclosed CD or the site
www.meliconi.com/guide. As well as easily finding the code to programme your remote control, consult
the on-line guide to help you to find which keys on the UNIVERSAL 3-300 remote control correspond
to the additional commands.
You can memorize the additional commands on the function keys F1 - F2 - F3 - F4 .
Normalization:
Brightness (+): or
Brightness (-): or
Colour (+): or
Colour (-): or
4
5 SEC.
or
If you know the exact code with which to programme the remote control, enter it as follows:
ENTERING THE CODE
+++
11
...................................................... = 1
.......................................... = 3
= 0
....................... = 6
Code obtained = 1306
The functions Mute , Vol - , Vol + and AV are memorized on the keys F1 , F2 , F3 , F4 . These functions
can be used to control appliances other than the TV. For further information consult the enclosed CD or
the on-line guide on the site www.meliconi.com/guide.
or
5 SEC.
or or

5
PROBLEM SOLVING
INFO-LINE
If you have any queries about your UNIVERSAL 3-300 remote control:
• read this Instruction Booklet carefully - you will find an answer to most of your questions
• consult the enclosed CD or our website where you will find the answers you need easily and quickly.
SOLUTION
Try some of the other frequently-used keys. If the
problem persists, check that the batteries are fitted
correctly. If necessary, replace them with 2 new 1.5
V AAA/LR03 batteries.
Check that the batteries are new and that the remote
control is pointing at the TV without any obstacles in
the way. If required, reset the remote control code,
following the programming procedure.
The batteries are low. Change them.
You may have used the wrong code. Reset the remote
control code, following the programming procedure.
To find the code with which to programme your remote
control consult the enclosed CD or on-line guide at
www.meliconi.com/guide.
PROBLEM
The appliance does not respond and the TV -
DVD - SAT selection keys do not light up
when a key is pressed.
The appliance does not respond but the
selection keys do light up.
The selection keys flash.
The remote control commands are not all
working correcting.
The code for your appliance make is not in
the Code Book.
WARRANTY: 2 years
The warranty ceases to be valid if the product
is tampered with or used incorrectly.
Remote control type GumBody
Model UNIVERSAL 3-300
Purchase date / /
Dealer’s stamp
The symbol of the crossed trash can shown on the remote control indicates that once the product has reached the end of its working life it
should be disposed of separately from other waste. The user should, therefore, take the remote control to a specialised collection centre
for electronic and electrical waste, or hand it over to the dealer when purchasing a new similar remote control, on a one to one basis. Correct
separated collection for subsequent recycling, processing and environmentally compatible disposal contributes in preventing possible
negative effects on the environment and on health and favours the recycling of the materials used in producing the remote control. Improper
disposal of the product by the user leads to application of the penalties as per legislative decree no. 22/1997 (article 50 and following of
decree no. 22/1997).