Leenders Warne User manual

WARNE
INSTALLATION EN

WARNE LEENDERS
201850.001.I.EN
Points of aenon installaon Warne
Tools required:
• Phillips screwdriver or cordless drill with a Phillips screwdriver bit
• 10 mm open-ended spanner
• 3 mm Allen key
Transport
Remove the wood screw and the shipping
bracket, and take the Warne o the
pallet.
Use protecve padding when moving the
Warne with a hand truck against the front
face.

WARNE LEENDERS
201850.001.I.EN
Top or rear outlet
Unless specied dierently at the me of
order, the Warne is supplied with a top
ue gas outlet as standard. The top ue
gas outlet can easily be converted to a
rear outlet.
Remove the round outlet stub from the
top face. Remove the break-out plate in
the convecon wall. Next, remove the
cover plate from the rear face and t it
to the top face. Make sure that the at
ribbon stays in place. Fit the outlet stub
to the rear face.
Fresh air supply (oponal)
Mount the stub to the air plenum.
Connect the exible pipe to the stub. For
a connecon in the wall or behind the
Warne, remove the break-out plate at the
rear of the base.
Adjusng the base
Use the 2 adjustment screws at the back
of the base to prevent the Warne from
wobbling on an uneven surface.

WARNE LEENDERS
201850.001.I.EN
Check the interior
The interior parts may shi slightly during
shipping.
Through the outlet, check that the air
pipes at the boom are connected
correctly..
Make sure that the heat shield is properly
seated at the boom.
Inspecon
Pay close aenon to the following points aer installing the Warne:
• Check that the Warne stands securely on its base.
• Make sure that no combusble and/or explosive items (paper, cardboard, spray cans,
etc.) have been le in or close to the Warne.
• If the ue pipe is in working condion, check operaon of the ue and the air supply
to the Warne by lighng a re. Follow the instrucons in the manual.

WARNE LEENDERS
201850.001.I.EN
General instrucons and regulaons
Installaon
• To secure the warranty, the Warne must be installed by a properly qualied person employed by
a dealer recognized by Harrie Leenders Haardkachels. See leenders.nl for a current list of
addresses of recognized dealers or contact the manufacturer.
• The stove is suscepble to scratching. Handle with care.
• Aer installaon, check the draught by burning some kindling wood.
Use
• All local regulaons including those referring to naonal and European standards must be
observed when installing the appliance.
• Ensure there is sucient venlaon/air supply in the room where the stove is installed.
Air extractors such as a cooker hood may cause problems due to ue gases escaping from the
stove into the room.
• The appliance is not suitable for a shared ue system.
• The appliance must be installed on a oor having sucient bearing capacity.
• Ensure adequate access for cleaning the appliance, the ue-gas connecon and the chimney.
Safety instrucons
• Glass is quite suscepble to breaking and broken glass is quite sharp. Take appropriate measures.
• For general safety, we refer to the VCA guidelines.
• Note: Aer installaon, ensure there is no inammable and/or explosion-hazardous material in or
on the stove such as a spray can, packing material and the like.
Distance to combusble materials
Back: 150 mm
Side: 250 mm
Front: 1000 mm
Specicaons Warne
• Nominal power = 4.9 kWh
• Flue gas mass ow = 4.1 g/s
• Appliance weight = 153 kg
• Minimum chimney draught = 0,12 mbar
• Flue gas temperature directly over the stove = 217 °C
• Energy Eciency 84.4%, class A+, index 113,4
A
+