LEF LIGHTING LEMC45D User manual

LEF LIGHTING S.R.L. | www.leflighting.it
Via Rodolfo Morandi, 9/11 - 50019 Sesto Fiorentino (FI) - ITALY | Tel [phone] - Fax [phone]
MADE IN P.R.C.
LEMC45D, LEMC45HD
M M IP20 ta tc PFC
λ≥0,95
MAX 50°C MAX 85°C WATT 80mm
45 cc
LEMC45D 220-240 50÷60
24
35
42
45
350
500
600
700
800
900
1050
170
21-43
(W)
Tensione
di ingresso
Input voltage
Frequenza
di rete
Input frequency
Potenza
di uscita
Output power
Comando
Command
(Vdc)
Tensione
di uscita
Output voltage
(mA)
Corrente
di uscita
Output current
( )λ
PFC
(g)
Peso
Weight
PUSH
DALI
CC
CV
CC
25-50
25-56
25-64
25-70
0,95
0,90
LEMC45HD 220-240 50÷60 45
1050
1150
1200
1300
1400
1500
1600
170
14-28
PUSH
DALI CC
14-30
14-32
14-35
14-39
0,95
14-43
14-38
DIM
PUSH
230Vac
DALI
DT6
DIM
DALI
EE
87%
DIP
SWITCH
LED
COB
Dimmable constant multicurrent LED drivers (CC)
with push-button (PUSH) and DALI signal control IP20
USER GUIDE
General Characteristics
Plastic case
Driver for indipendent mounting
Electric class protection II
Protection degree IP20
Reference Standards
Technical Features
Input voltage range 220-240Vac
Input frequency 50÷60Hz
Constant current output 350÷1050mA (LEMC45D)
Constant current output 1050÷1600mA (LEMC45HD)
(settings by dip-switch)
Factory setting: 350mA (LEMC45D)
Factory setting: 1050mA (LEMC45HD)
Brightness adjustement through:
- push-button (PUSH 230Vac)
- DALI signal
«LEVEL MEMORY» and «STATUS MEMORY» function
Energy Efficiency (EE) 87%
Open circuit Protection (OCP)
Overload protection (OLP)
Short circuit protection (SCP)
Powerfactorcorrection(PFC)λ≥0,95
Operating ambient temperature Ta -20°C ÷ +50°C
Max case temperature on Tc 85°C AEE Identification nr.IT18040000010321
PRODUCT TO BE DISPOSED
DIFFERENTLY FROM URBAN WASTE
ATTENTION:
The installation of the product must be
followed by qualified personnel.
If the product is used for purposes other
than the original ones or if it is connected
incorrectly, LEF Lighting S.R.L. will not
accept any responsibility for damages
caused.
N.B.
Power supply not suitable for
no-load operation.
[AA] Rev. v1.10 31/03/2022
EN 55015
EN 61000-3-2
EN 61000-3-3
EN 61347-1
EN 61347-2-13
EN 61547
EN 62386-207
EN 62493
www.leflighting.it

LEF LIGHTING S.R.L. | www.leflighting.it
Via Rodolfo Morandi, 9/11 - 50019 Sesto Fiorentino (FI) - ITALY | Tel [phone] - Fax [phone]
[AA] Rev. v1.10 31/03/2022
Wiring diagrams
USER GUIDE
LEMC45D, LEMC45HD
- Briefly press the button to switch on (ON)
and switch off (OFF).
- Long press of the button for dimming.
With a new long press of the button,
the dimming restarts in the opposite direction.
The dimming level is set by the value of the DALI signal sent by the DALI control unit.
OPERATING MODES
There are 2 distinct modes of operation : DALI and PUSH-BUTTON (PUSH 230Vac)
DALI MODE
PUSH 230Vac MODE
PUSH 230Vac MODE - Synchronization by cable
If the power supplies lose synchronization,
they can be resynchronized again by
pressing the BUTTON for 15 seconds with
the light off.
- Briefly press the button to switch on (ON)
and switch off (OFF).
- Long press of the button for dimming.
With a new long press of the button, the dimming
restarts in the opposite direction.
Maximum number of synchronizable
power supplies: 5
Cable length of the BUTTON: 15 m