LEF LIGHTING NEXTA RADIO TOUCH-1DIM User manual

TOUCH-1DIM TOUCH-1RGB TOUCH-1CCT 1.1 DESCRIZIONE
Radiocomando rolling code 433.92 MHz
TOUCH-1DIM: 1 canale, funzioni dimmer
TOUCH-1RGB: 1 canale, funzioni RGBW
TOUCH-1CCT: 1 canale, funzioni CCT
1.2 DATI TECNICI
AREA TOUCH / TOUCH AREA
AREA TOUCH / ZONE TOUCH
BATTERIA / BATTERY
BATTERIE / BATTERIE
1
IT
2
Batteria CR 2450
Circa 3 anni
Rolling code
433.92 MHz ISM
100 m (interno di edifici: 40 m)
40 mm x 40 mm h 10 mm
Alimentazione
Durata batteria
Codifica
Frequenza radio
Portata
Dimensioni
1.2 TECHNICAL DATA
Battery CR 2450
About 3 years
Rolling code
433.92 MHz ISM
100 m (40 m inside buildings)
40 mm x 40 mm h 10 mm
Power supply
Battery life
Code
Radio frequency
Range
Dimensions
2PROGRAMMAZIONE DEL TRASMETTITORE
Con questa procedura si programma un canale per abbinarlo a una ricevente compatibile.
Per eseguire la seguente procedura è necessario accedere alla ricevente.
PROCEDURA:
1- Attivare la ricevente sulla quale si vuole utilizzare il trasmettitore in modalità
“programmazione radio di trasmettitori multifunzione” e selezionare la funzione che
si desidera abbinare al tasto (vedi il manuale della ricevente)
2- Fare una pressione con il tasto desiderato, il led della ricevente emette
tre lampeggi per segnalare l’avvenuta ricezione.
3- Il trasmettitore torna allo stato di stand by.
1.1 PRODUCT FEATURES
Remote control rolling code 433.92 MHz
TOUCH-1DIM: 1 channel, dimmer function
TOUCH-1RGB: 1 channel, RGBW function
TOUCH-1CCT: 1 channel, CCT function
EN
2TRANSMITTER PROGRAMMING
This procedure is used to programme a channel in order to then associate it with a
compatible receiver. Access to the receiver is required to carry out the following procedure.
PROCEDURE:
1- Activate the receiver on which you want to use the transmitter in "multifunctional
remote control radio programming" mode and select the function that you want to associate with the
key (see receiver manual).
2- Press the desired key; the receiver's LED flashes three times
to signal it has been received.
3- The transmitter goes back into stand-by.
PRESSIONE BREVE / SHORT PRESS /
PRESSION BRÈVE / KURZES DRÜCKEN
PRESSIONE LUNGA / LONG PRESS /
PRESSION LONGUE / LANGES DRÜCKEN
TOUCH-1DIM = OFF
TOUCH-1RGB / TOUCH-1CCT =
Dimmer Up / Down
SLIDE
1
2
+

1.1 BESCHREIBUNG
Fernbedienung Rolling-Code 433.92MHz
TOUCH-1DIM: 1 Kanal, dimmer Funktion
TOUCH-1RGB: 1 Kanal, RGBW Funktion
TOUCH-1CCT: 1 Kanal, CCT Funktion
1.2 TECHNISCHE DATEN DE
Batterie CR 2450
Etwa 3 Jahre
Rolling code
433.92 MHz ISM
100 m (40 m in Gebäuden)
40 mm x 40 mm h 10 mm
Versorgung
Lebensdauer Batterie
Kodierung
Funkfrequenz
Reichweite
Abmessungen
1.2 DESCRIPTION TECHNIQUE
Batterie CR 2450
Environ 3 ans
Rolling code
433.92 MHz ISM
100 m (40 m l'intérieur)
40 mm x 40 mm h 10 mm
Alimentation
Durée de la batterie
Codification
Fréquence radio
Portée
Dimensions
2PROGRAMMIERUNG DES TRANSMITTERS
Mit diesem Vorgang wird ein Kanal programmiert, um ihn mit einem kompatiblen Empfänger zu
verbinden. Um folgenden Vorgang durchzuführen, ist es notwendig, Zugriff zum Empfänger zu haben.
VORGANG:
1- Empfänger, auf dem der Transmitter verwendet werden soll, im Modus „Funk-Programmierung von
allgemeinen Transmittern“ aktivieren und die Funktion auswählen, die der Taste zugeordnet werden soll
(siehe Handbuch des Empfängers)
2- Die gewünschte Taste einmal drücken, die LED des Empfängers blinkt dreimal, um anzuzeigen,
dass sie das Signal empfangen hat.
3- Der Transmitter kehrt auf Stand-by zurück.
1.1 DESCRIPTION
Radiocommande Rolling Code 433,92MHz
TOUCH-1DIM: 1 canal, dimmer Funktion
TOUCH-1RGB: 1 canal, RGBW Funktion
TOUCH-1CCT: 1 canal, CCT Funktion
FR
2PROGRAMMATION DE L’EMETTEUR
This procedure is used to programme a channel in order to then associate it with a
compatible receiver. Access to the receiver is required to carry out the following procedure.
PROCEDURE:
1- Activate the receiver on which you want to use the transmitter in "Funkprogrammierung
multifunktionaler Fernbedienungen" mode and select the function that you want to associate with the
key (see receiver manual).
2- Press the desired key; the receiver's LED flashes three times
to signal it has been received.
3- The transmitter goes back into stand-by.
V1.0
TOUCH-1DIM
TOUCH-1RGB
TOUCH-1CCT
LEF LIGHTING S.R.L.
Via Rodolfo Morandi 9/11
50019 Sesto Fiorentino
Tel. [phone]
Firenze - ITALY
www.lef.it