Legacy Crib’n’double bed User manual

H02798:05/04 1

ASSEMBLY DIRECTIONS AND PARTS LIST

DirectionsforMaintenance,Cleaning,Storage,andUseofyourCrib’n’DoubleBedarealsoincluded.

TODDLER BED

CHILD CRAFT INDUSTRIES, INC.

P.O. Box 444, Salem, IN USA 47167-0444 / PH: 812-883-3111 / FAX: 812-883-1819 / www.childcraftindustries.com

CRIB’N’DOUBLE BED CONVERTS TO TODDLER BED

AND FULL SIZE HEADBOARD AND FOOTBOARD

FULL SIZE

HEADBOARD AND FOOTBOARD

CRIB

(STYLE MAY VARY)

M BEFORESTARTINGTHEASSEMBLYPROCEDURE,READALLDIRECTIONSWITHCARE.

M YOU WILL NEED THE FOLLOWING FOR THE ASSEMBLY OF YOUR LEGACY BED:



#1 & #2 phillips screwdrivers 



slotted screwdriver 



5/16” & 7/16” wrenches or two adjustable wrenches 



enclosed Allen Wrenches a& b

H02798:05/042

(1) Spring Zplastic

pouch

(1) Foot Post Left U(1) Foot Post RightV

(1) ShortHead

SectionS(1) ShortFoot

SectionT

(1) Stationary Post Right P(1) Stationary Post Left O

(1) StretcherY

(foruseonToddlerBedonly)

(2) Stabilizing Bars R(attached to Spring

)

(1) Stationary SideAssemblyQ(1) Long FootAssembly W

(20) Washer Head

Machine Screws B

H00179

(actual size)

(4) Scissor Arm

Assemblies A

H01214

(20) Lock Nuts C

H00133

(actual size)

(8) Allenhead Bolts F

H01169 (actual size)

(6) Allenhead Bolts G

H01130 (actual size)

(4) Allenhead Bolts H

H01168 (actual size)

(2) Allenhead Bolts L

H01123 (actual size)

(4) Joint Connect Nuts I

H00147 (actual size)

(2) End Plates - Right E

H00330

(2) End Plates - Left D

H00329

(4) Wooden Dowels X

H00910 (actual size)

(2) Insert Nuts M

H00136

(actual size)

(8) Insert Nuts N

H00157

(actual size)

(8) Truss Head Machine Screws J

H00127

(actual size)

(1) Allen Wrench b

(5mm) H01105

(1) Allen Wrench a

(5/32”) H00280

Label

12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678

234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567

12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678

ARTS

NCLOSED

ARDWARE

(

NOTED

WHEN

SHOWN

ACTUAL

SIZE

)

12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678

234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567

12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678

ARTS

NCLOSED

ARTON

H02798:05/04 3

12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678

234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567

12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678

Carefully remove and lay out all hardware and parts. Check quantities and match the Hardware List and the Parts List. NOTE: During

the assembly process, when using screws or bolts, check each with the PARTS ENCLOSED IN HARDWARE BAG list by letter and size

identification. Place each screw or bolt on the diagram of the item which is sketched actual size. Be sure to use the proper size

specified in the assembly directions. If a part is missing or broken contact your Legacy dealer or Child Craft, P.O. Box 444, Salem, IN

47167-0444 USA, 812-883-3111, http://www.childcraftindustries.com for replacement part(s) or instructional literature. Before mak-

ing this contact identify your Crib’n’Double Bed by the model identification number stamped on the label attached to the inside face of

Short Foot Section Tbottom rail. Make note of all identification numbers and include this information with your request. DO NOT

SUBSTITUTE PARTS! Record your model identification number here for future identification:

Model #_________________________________________

Long arm of Scissor Arm Assembly AA

Short arm of

Scissor Arm

Assembly AA

Short arm of Scissor Arm Assembly AA

lowest position

middleposition

highest position

UNDERSIDE OF SPRING TT

plastic pouch

See Enlarged View

plastic insert in Lock Nut CC

EnlargedView

Long arm of

Scissor Arm

Assembly AA

STEP 2-DIAGRAM 2:ASSEMBLE STABILIZING BARS

See Enlarged View

Enlarged View

Plastic insert in

Lock Nut C

Dor EEnd Plate

INSTALL END PLATES DD

AND EE

EEXACTLY AS SHOWN C

Mount an End Plate - Right EE

Eand an End Plate - Left DD

Dto ends of each Stabilizing Bar RR

Rusing (4) Washer Head Machine Screws BB

Band

(4) Lock Nuts CC

Cin each Stabilizing Bar RR

Rexactly as shown. IMPORTANT: End Plates DD

D& EE

Emust be positioned in the correct mounting

holes on Stabilizing Bars RR

Rexactly as shown. Tighten down Washer Head Machine Screws BB

Band Lock Nuts CC

Csecurely using a 5/16

inch and a 7/16 inch wrench.

12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678

234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567

12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678

234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567

12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678

PREPARATION

STEP 1-DIAGRAM 1:ASSEMBLE SPRING

Attach the short section of the (4) Scissor Arm Assemblies AA

Ato Spring ZZ

Zusing (4) Washer Head Machine Screws BB

Band (4) Lock Nuts

Cplaced exactly as shown in D

IAGRAM

1. NOTE: The metal threads of Lock Nuts

are to be inserted first over Washer Head Machine

Screws

as shown in Enlarged View.Be sure to use the proper receiving holes in Spring ZZ

Zas shown. This procedure will be

accomplished from the underside of Spring ZZ

Z. Tighten all (4) Washer Head Machine Screws BB

Bwith a 5/16 inch wrench while holding

Lock Nuts CC

Cwith a 7/16 inch wrench. Tighten each assembly securely.

H02798:05/044

Attach Foot Post Right Vand Stationary

Post Right Pto Short Foot Section Tas

shown. Lay all three pieces horizontal on

a soft surface (carpet) and start by insert-

ing Allenhead Bolt Fthrough its upper re-

ceivinghole in the corner post of Short Foot

Section Tand into the factory installed

threaded insert in Foot Post Right Vand

StationaryPost RightP. Startthreadsthree

orfour turns usingAllenWrench a. Do not

fully tighten at this time.

Insert Allenhead Bolt Fthrough the lower

receiving hole located in the corner post of

ShortFoot Section Tand into the threaded

insert in Foot Post Right Vand Stationary

Post Right P. Once Allenhead Bolts F

are properly aligned and both are started

into their threaded inserts, tighten both se-

curely using Allen Wrench a. Follow the

same procedure for attaching Foot Post

Left UandStationaryPost Left Oto Short

Head Section S. Insure allAllenhead Bolts

are tightened securely before continuing

with next step.

NOTE:Start Allenhead Bolt

F(attop) into itsthreaded

insert(do not fully tighten)

beforeinstallingAllenhead

Bolt FF

F(at bottom). Threaded

insert will

receive

12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678

234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567

12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678

STEP 3 - DIAGRAM 3:ATTACH POSTS TO SHORT FOOT AND HEAD SECTION

RENLARGEDVIEW

Locate a Stabilizer Bar R(the two are interchangeable). Align the holes in End Plate-Right E(attached to a Stabilizer Bar R) with the

holesin thebottom rail ofShort FootSectionS. Refercloselyto DIAGRAM 6 below. Donot attach StabilizerBar

backward. Placean Insert

Nut Ninto the top hole in Short Foot Section Sbottom rail from the opposite side (outside of crib). Hold Insert Nut Nin the hole with

Allen Wrench awhile you insert Truss Head Machine Screw Jthrough the top (oblong) hole in End Plate-Right Eand into Short Foot

Section Sbottom rail. Thread Truss Head Machine Screw J

intoInsertNutN.Donotfullytightenatthistime.PlaceanInsert

NutNintothe bottom hole fromthe opposite sideandhold with

AllenWrencha.Insert a Truss Head MachineScrew Jinto the

bottomholeinEndPlate-RightE.RefertoENLARGEDVIEWin

DIAGRAM 6 below. Tighten both Truss Head Machine Screws J

securely. Use the same procedure to attach the other end of

Stabilizer Bar Rto Short Head Section S. Once the first

StabilizerBarRisin place,attachthe secondStabilizer BarR

by using the same method.

OBLONG

HOLE

SEE

ENLARGED

VIEW

12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678

234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567

12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678

STEP 4 - DIAGRAM 4:ATTACH STABILIZING BARS TO FOOT AND HEAD SECTIONS

H02798:05/04 5

12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678

234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567

12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678

Read this entire step before starting the procedure to select a Spring ZZ

Zheight position

and to attach Spring ZZ

Zto the Stabilizing Bars RR

R. Review Diagram 1.

1.Decide on your preference of height placement of Spring ZZ

Z. You have three position choices, highest, middle and lowest, holes in

Spring ZZ

Zare noted in Diagrams 1 and 5. After you select your height, attach one end of the long end of Scissor Arm Assembly AA

Ato

Spring ZZ

Zbyfirst inserting a WasherHead Machine Screw BB

Bthrough selected position holein Spring ZZ

Zthenthrough one end of Scissor

Arm Assembly AA

A,add a Lock Nut CC

C,(with metal threads of Lock Nuts

to be inserted first), exactly as shown. Repeat this procedure

until one end of each of the (4) Scissor Arm Assemblies AA

Ais attached to Spring ZZ

Zat the same height position. Tighten all (4) Washer

Head Machine Screws BB

Bwith a 5/16 inch wrench while holding Lock Nuts CC

Cwith a 7/16 inch wrench. Tighten each assembly securely.

2.SpringZZ

Zwill attachto the outsideholes in thetwo installed StabilizingBars RR

R. Inserta WasherHead Machine Screw BB

Bfirstthrough

the remaining long end of the Scissor Arm Assembly AA

Athrough the hole in Stabilizing Bar RR

R, add a Lock Nut CC

C(with metal threads

of Lock Nut

to be inserted first). See Diagram 5 and follow the procedure exactly. Repeat the procedure with the remaining (3) long

ends of the Scissor Arm Assemblies AA

Ato Stabilizing Bars RR

R. Tighten all (4) Washer Head Machine Screws BB

Bwith a 5/16 inch wrench

while holding Lock Nuts CC

Cwith a 7/16 inch wrench. Tighten each assembly securely.

3.Whenever you decide on another height position first remove the crib mattress. Remove Spring ZZ

Zby detaching the spring from the

Stabilizing Bars RR

R.Loosenand removethe (4)LockNuts CC

Candremovethe (4) Washer HeadMachineScrewsBB

B(installedin

above)

with a 5/16 inch wrench while holding Lock Nuts CC

Cwith a 7/16 inch wrench. Carefully lift the spring from the crib. Make your selected

height position change by following 11

1. of this Step. Then follow 22

2.to reinstall Spring ZZ

Z, again tighten all Washer Head Machine Screws

Bsecurely as directed.

NOTE:CRIBENDSARE DELETED

FROMDIAGRAMFOR CLARITY

&DETAIL.

Stabilizer Bars RR

with End Plates

D & EE

Eattached

lowest position

middleposition

highest position Long arm of

Scissor Arm

Assembly AA

Short arm of

Scissor Arm

Assembly AA

STEP 5-DIAGRAM 5:INSTALL SPRING

H02798:05/046

12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678

234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567

12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678

STEP 6-DIAGRAM 6:ATTACH STATIONARY SIDE AND LONG FOOT ASSEMBLIES

NOTE: It may be necessary to loosen Truss Head Machine Screws

on the Stabilizing Bar

near Stationary Side Assembly

.Attach Stationary Side Assembly Qto Headboard and Footboard Assemblies. Insert a Wooden Dowel Xinto the receiving hole

in each end of Stationary Side Assembly Qtop dowel. See DETAIL A. Insert the other end of the (2) Wooden Dowels Xinto their

receiving holes (top hole) in Stationary Posts O& P. Insert an Allenhead Bolt Gthrough the hole near the top of Stationary Posts O

& Pand into the threaded inserts in Stationary SideAssembly Q. UsingAllen Wrench atighten four or five revolutions but do not fully

tighten at this time. Insert an Allenhead Bolt Hthrough the receiving hole near the bottom of Stationary Posts O& Pand into the

receiving holes in Stationary Side Assembly Q. Insert a Joint Connect Nut Iinto holes in the bottom rail of Stationary Side Assembly

Q. Using a slotted screwdriver, align their threaded hole with the threads on Allenhead Bolts H. See DETAIL B. Hold Joint Connect

Nuts Iin position with a slotted screwdriver and tightenAllenhead Bolts HusingAllen Wrench a. UsingAllen Wrench afully tighten

the (4)Allenhead Bolts G&Hat this time. Attach Long FootAssembly Wto Headboard and FootboardAssemblies. NOTE: It may

be necessary to loosen Truss Head Machine Screws

on the Stabilizing Bar

near Long Foot Assembly

. Insert Wood

Dowels Xin the ends of the top dowel on Long Foot Assembly W. Spread Foot Posts U& Vjust enough to allow Wood Dowels

Xto fit into their receiving holes in Foot Posts U& V. Insert an Allenhead Bolt Gthrough the hole near the top of Foot Posts U&

Vand into the threaded insert in the top rail of Long Foot Assembly W. Tighten four or five revolutions but do not fully tighten at this

time. Insert anAllenhead Bolt Gthrough the hole near the bottom of Foot Posts U& Vand into the threaded insert in the bottom rail

of Long Foot Assemly W. Using Allen Wrench a, tighten the (4) Allenhead Bolts Gat this time. Retighten all Truss Head Machine

Screws Jwhich were loosened.

DETAIL B

NOTE: STABILIZING BARS AND

SPRINGINSTALLEDINSTEP4&5

ARE DELETED FROM DIAGRAM

FORCLARITY&DETAIL. T

THREADED INSERT

THREADED

INSERT

THREADED

INSERT

THREADED INSERT

Locator hole will

receive XX

Threaded insert

will receive GG

DETAIL A

H02798:05/04 7

12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678

234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567

12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678

When use as a crib has been completed, you have the option to convert to a Toddler Bed for years of additional use in your child’s

room. Refer to Step 5 - Diagram 5 to move Spring Z.Remove Long FootAssembly Wthat is attached to Foot Posts U& V. Install

Crib Stretcher Yas shown in Sketch A. Dowel on Stretcher Ylocates in top hole at bottom of Foot Posts U& V, then secure with

Allenhead Bolt Hand Joint Connect Nut Ishown installed. Install Insert Nut MandAllenhead Bolt Lin holes near top of Foot Posts

U& Vas shown. Tighten Allenhead Bolt Lwith Allen Wrench aand Insert Nut Mwith Allen Wrench b. Spring ZZ

Z must be

installed in lowest position. Store the removed parts and hardware in the event you wish to convert your toddler bed back to a crib.

12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678

234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567

12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678

Disassemble crib by removing Spring Z. Also re-

move Short Head Section Sand Short Foot Section

Tfrom Foot PostsU& Vand Stationary Posts O&

P. Attachthe Stationary SideAssembly O/P/Qand

the Long Foot Assembly U/V/Wto “Hook-End”

style full size bed rails (Model #6444) at the desired

height. The “Hooks” on the bed rails locate over the

factory installed pins in the slots in Foot Posts U&

Vand Stationary Posts O& P.

O/Q/P

Spring Zmust be

installedinlowest

positionas shown.

Purchased Mattress see size

requirements under WARNING

NOTE: When using as a Toddler Bed the

mattress must have minimum dimen-

sionsof 51-5/8 in.(1310mm) in lengthand

27-1/4 in. (690mm) in width and 4 in.

(100mm) in thickness but not to exceed

6 in.

It is very important that Stretcher YY

Yis

used when converting to a Toddler Bed.

Failure to install this part could result

in serious injury or death.

When using as a Toddler Bed, the mini-

mum age shall not be less than 15

months and the maximum weight shall

not be greater than 50 lb (22.7 kg).

WARNING

O/P/Q

U/V/W

Model

# 6444

SketchA

CONVERSION TO AFULL SIZE HEADBOARD &FOOTBOARD

ONVERSION

ODDLER

MAINTENANCE OF YOUR LEGACY CRIB/TODDLER BED/FULL SIZE HEADBOARD & FOOTBOARD: Upon completion of assemblybesureallscrews,

bolts and fastening devices have been tightened securely. A frequent check should be made of all screws, bolts and fastening devices and tightened

if needed. Before each usage or assembly, inspect crib for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use crib if parts are

missing or broken. Contact your Legacy Dealer or Legacy at (812) 883-3111, or http://www.childcraftindustries.com, for a replacement part or

instructional literature if needed. Include Model Identification Number with your request which you recorded on Page 3 of these instructions. DO NOT

SUBSTITUTE PARTS. DO NOT MAKE ANYALTERATIONS NOT DESCRIBED IN THESE ASSEMBLY DIRECTIONS.

CLEANINGINSTRUCTIONS FOR YOUR LEGACY CRIB/TODDLER BED/FULL SIZE HEADBOARD& FOOTBOARD: Mix together amildsolutionof gentle

dishwashing liquid and water, apply to surface using a soft clean cloth lightly dampened in the solution. Rinse with clear water again using a soft clean

cloth,thendry all surfaces thoroughly with asoftdry cloth. NO ABRASIVE CLEANERS, SCOURING PADS, STEELWOOL, OR COARSE RAGS SHOULD

BEUSED TOCLEAN THIS FINEFURNITURE.

STORAGEAND USE OF YOUR LEGACYCRIB/TODDLER BED/FULL SIZE HEADBOARD & FOOTBOARD: Aprintedplasticpouchisattachedto the crib

spring for the permanent storage of the assembly directions. After completing the assembly process you are advised to read and be aware of all

WARNINGS, CAUTIONS, CLEANING, STORAGE, USE AND MAINTENANCE notices contained in this set of directions and printed on the plastic pouch

located on the underneath side of the crib spring. You will then place the complete set of assembly directions into the plastic pouch for future referral.

We caution you not to place excess hardware in the plastic pouch as it could present danger to a child if retrieved. When storing crib use CAUTION as

extreme temperature or humidity changes could be harmful. Use CAUTION when a vaporizer is in use, always aim vapor stream away from crib as well

as away from any wood furniture item.

H02798:05/048

WARNING

VFAILURE TO FOLLOW THESE WARNINGS AND ASSEMBLY IN-

STRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.

VREADALL INSTRUCTIONS BEFOREASSEMBLING CRIB. KEEP

INSTRUCTIONS FOR FUTURE USE. A PLASTIC POUCH IS ATTACHED TO

CRIB FOR PERMANENT STORAGE OF THE INSTRUCTIONAL LITERATURE.

VBEFOREEACHUSAGEORASSEMBLY,INSPECTCRIBFORDAM-

AGED HARDWARE, LOOSE JOINTS, MISSING PARTS OR SHARP

EDGES. DO NOT USE CRIB IFANY PARTS ARE MISSING OR BRO-

KEN. ASK YOUR DEALER OR WRITE TO LEGACY, P.O. BOX 444,

SALEM, IN 47167-0444 USA (812)-883-3111) FOR REPLACEMENT

PARTS AND INSTRUCTIONAL LITERATURE IF NEEDED. INCLUDE

MODEL IDENTIFICATION NUMBERS WITH YOUR REQUEST WHICH YOU RECORDED

ON PAGE THREE. DO NOT SUBSTITUTE PARTS.

VAFTER RAISING SIDE, MAKE SURE LATCHES ARE SECURE. IF

YOUR UNIT HAS ADROP SIDE.

VWHENCHILDISABLE TO CLIMB OUTORREACHES THE HEIGHT

OF 35 INCHES (90 CENTIMETERS) THE CRIB SHALL NO LONGER

BE USED.

VDO NOT PLACE CRIB NEAR WINDOW WHERE CORDS FROM

BLINDS OR DRAPES MAY STRANGLE A CHILD.

VIF REFINISHING, USE A NON-TOXIC FINISH SPECIFIED FOR

CHILDREN’S PRODUCTS.

VDO NOT LEAVE CHILD IN CRIB WITH SIDE LOWERED. BE SURE

SIDE IS IN RAISEDAND LOCKED POSITION WHENEVER CHILD IS

IN CRIB.

VWHEN CHILD IS ABLE TO PULL TO STANDING POSITION, SET

MATTRESS TO LOWEST POSITIONAND REMOVE BUMPER PADS,

LARGE TOYS AND OTHER OBJECTS THAT COULD SERVE AS

STEPS FOR CLIMBING OUT.

VNEVERUSEPLASTICSHIPPINGBAGSOR OTHER PLASTIC FILM

AS MATTRESS COVERS BECAUSE THEY CAN CAUSE SUFFOCA-

TION.

VDO NOT USE A WATER MATTRESS WITH THIS CRIB.

VREPLACE TEETHING RAIL(S) IF DAMAGED OR LOOSE. (IF

EQUIPPED WITH TEETHING RAILS.)

VSTRINGSCANCAUSESTRANGULATION! DONOTPLACEITEMS

WITH A STRING AROUND A CHILD’S NECK, SUCH AS HOOD

STRINGS OR PACIFIER CORDS. DO NOT SUSPEND STRINGS

OVER A CRIB OR ATTACH STRINGS TO TOYS.

VREMOVE ALL CRIB TOYS WHICH ARE STRUNG ACROSS CRIB

AREAWHEN YOUR CHILD IS BEGINNING TO PUSH UP ON HANDS

AND KNEES OR IS 5 MONTHS OF AGE, WHICHEVER OCCURS

EARLIEST. THESE TOYS CAN CAUSE STRANGULATION.

VWHENDISASSEMBLINGTHIS CRIB, DONOT REMOVEANYITEM

ATTACHED WITH WOOD SCREWS.

VALWAYS ENSURE A SAFE ENVIRONMENT FOR THE CHILD BY

CHECKING REGULARLY, BEFORE PLACING THE CHILD IN THE

CRIB, THAT EVERY COMPONENT IS PROPERLY AND SECURELY

IN PLACE.

VANY MATTRESS USED IN

THIS CRIB MUST BE AT

LEAST 27-1/4 INCHES (69

CENTIMETERS), BY 51-5/8

INCHES (131 CENTIME-

TERS), WITHATHICKNESS

NOT EXCEEDING 6 INCHES

(15 CENTIMETERS).

THE DIMENSIONS OF THE MAT-

TRESS SHALL BE TAKEN FROM

SEAM TO SEAM OR EDGE TO EDGE

WHEREAPPROPRIATE.

VUPON COMPLETION OF

ASSEMBLY BE SURE ALL

SCREWS, BOLTS AND FAS-

TENING DEVICES HAVE

BEEN TIGHTENED SE-

CURELY. A FREQUENT

CHECK SHOULD BE MADE

OF ALL SCREWS, BOLTS

AND FASTENING DEVICES

AND TIGHTEN IF NEEDED.

CHILD CRAFT INDUSTRIES, INC.

P.O. BOX 444

SALEM, IN 47167-0444 USA

PH:812-883-3111

FAX:812-883-1819

http://www.childcraftindustries.com

CAUTION

This manual suits for next models

Table of contents

Other Legacy Indoor Furnishing manuals

Legacy

Legacy LADDER BARREL User manual

Legacy

Legacy 1310-4206 User manual

Legacy

Legacy C1930032 User manual

Popular Indoor Furnishing manuals by other brands

Omnimount

Omnimount OM1100346 instruction manual

Simpli Home

Simpli Home WyndenHall brooklyn+max AXWSH002-DCB quick start guide

Simpli Home

Simpli Home WyndenHall brooklin+max AXCBCDRP-03 Assembly instructions

HAMPTON BAY

HAMPTON BAY HB ACACIA BUTCHER BLOCK 1007 508 205 Use and care guide

Little Seeds

Little Seeds 6946321COM Assembly manual

West Elm

West Elm Mitchelle Side Table 6169465 Assembly instructions

Knape&Vogt

Knape&Vogt Shelf-Mate 244-BK installation instructions

Closet Maid

Closet Maid 11" Wide Single Tray Slider 3168 installation instructions

GAMA

GAMA BLQL181B Assembling Instruction

HOMEDEPOT

HOMEDEPOT Home Decorators HD645-M39-MCA Use and care guide

PB TEEN

PB TEEN Hampton Corner Media manual

Home Styles

Home Styles 88 5080 06 Assembly instructions

QU-AX

QU-AX TRENDY 54 04 46 Series manual

Bellamy

Bellamy Marylou quick guide

Home Styles

Home Styles 88 5180 15 Assembly instructions

Home Styles

Home Styles 88 5543 07 quick start guide

XROCKER

XROCKER 2021108 manual

HAMPTON BAY

HAMPTON BAY GENEVA FRS60704-2PKB Use and care guide

Legacy CRIB’N’DOUBLE BED User manual

Popular Indoor Furnishing manuals by other brands