Leitronic AG EasyAlarm EA-8-EXT Operating and maintenance manual

21 January 2008
Issue No.: 8.32
EA8-SENIOR-8-32-GB.doc
Motion detector
Siren-/Switch
module
Wired sensors
Alarm
Emergency
call button
Guardian angel in case of an emergency
Use instruction
EasyAlarm SENIOR®
LEITRONIC AG
Swiss Security Systems

2
Table of contents
1. Introduction.....................................................................................................................................................3
2. Safety instructions...........................................................................................................................................4
2.1 Approval ................................................................................................................................................................. 4
2.2 Telephone connection............................................................................................................................................. 4
2.3 Wireless sensors...................................................................................................................................................... 4
2.4 Power supply........................................................................................................................................................... 4
2.5 Safety notes............................................................................................................................................................. 4
3. Set view / Function elements ..........................................................................................................................5
4. Setup................................................................................................................................................................6
4.1 Safety instructions................................................................................................................................................... 6
4.2 Installation............................................................................................................................................................... 6
4.3 Operation with Plug&Protect-motion detector (EasyAlarm® SENIOR COMBI).................................................. 7
5. Wireless emergency button.............................................................................................................................8
5.1 Introduction............................................................................................................................................................. 8
5.2 Technical Specifications......................................................................................................................................... 8
5.3 Preparation for use.................................................................................................................................................. 8
5.4 Learn-in the wireless emergency button ................................................................................................................. 8
6. Programming...................................................................................................................................................9
6.1 How to program new calling numbers.................................................................................................................... 9
6.2 Designation of the calling number sequence......................................................................................................... 10
6.3 How to select user language / How to record individual message........................................................................ 10
6.4 How to program PIN-Code................................................................................................................................... 11
6.5 How to learn-in wireless emergency button / Range check .................................................................................. 11
6.6 Alarm criteria’s according to the position of the selection switch I/II/III............................................................. 12
6.7 How to program presence verification time-out.................................................................................................... 12
7. Operation.......................................................................................................................................................13
7.1 Self check at power on.......................................................................................................................................... 13
7.2 Inactive waiting period.......................................................................................................................................... 13
7.3 Supervision mode.................................................................................................................................................. 13
7.4 Alarm release........................................................................................................................................................ 14
7.5 Alarm delay / Pre warning period / Entry delay.................................................................................................... 14
7.6 Phone connection.................................................................................................................................................. 15
7.7 Alarm repetition.................................................................................................................................................... 16
7.8 Test call................................................................................................................................................................. 16
7.9 Dialling-in (check call) ......................................................................................................................................... 16
7.10 Answering an incoming call.................................................................................................................................. 16
8. Useful Notes..................................................................................................................................................17
8.1 Tone-dialling command........................................................................................................................................ 17
8.2 User information................................................................................................................................................... 17
8.3 Functional checks.................................................................................................................................................. 18
8.4 Battery check / replacement.................................................................................................................................. 18
8.5 Maintenance.......................................................................................................................................................... 18
9. Trouble Shooting / Error Handling ...............................................................................................................19
9.1 Telephone connection / Telephone communication.............................................................................................. 19
9.2 Wireless emergency button................................................................................................................................... 19
9.3 Acoustical monitoring........................................................................................................................................... 19
9.4 Motion detector activated for presence verification.............................................................................................. 20
9.5 Motion detector used as an alarm-sensor (sensor-1)............................................................................................. 20
10. Special programming ....................................................................................................................................21
10.1 Factory settings (Default-Values)......................................................................................................................... 21
10.2 Alarm repetition.................................................................................................................................................... 21
10.3 Entry / Exit periode............................................................................................................................................... 21
10.4 Mains power loss timeout..................................................................................................................................... 21
10.5 Signalling.............................................................................................................................................................. 21
10.6 Shared line with telephone/modem....................................................................................................................... 22
10.7 Dialling-in (Remote-access).................................................................................................................................. 23
10.8 Remote programming ........................................................................................................................................... 23
11. Accessories....................................................................................................................................................25
11.1 Siren EA-SIR........................................................................................................................................................ 25
11.2 230V-Switch EA-SWI .......................................................................................................................................... 25
11.3 Motion / Presence detector-PIR-F (Plug&Protect) ............................................................................................... 25
12. Specifications / warranty...............................................................................................................................27
12.1 Specifications........................................................................................................................................................ 27
12.2 Warranty ............................................................................................................................................................... 27
13. Index..............................................................................................................................................................28

3
1. INTRODUCTION
EasyAlarm®is an easy to use and reliable auto-dialler including announcement unit that can be used in many
ways. The most important functions are listed below. Please read the instruction manual carefully before you
start installation. Especially pay attention to the safety notes.
9EasyAlarm®calls automatically, when the emergency button is pressed. Up to nine calling numbers can
be stored. In case of an alarm these numbers will be called one after another until someone acknowledges
the alarm.
9EasyAlarm®puts in contact. After the individual recorded message has been announced a hands-free
communication is established and the alarmed person is in immediate contact with the person seeking
assistance and can take appropriate action!
9EasyAlarm®provides security. An authorised person can start a check call (dialling-in using PIN-Code)
at any time. Connection can be established in two ways (listening-in or hands-free connection).
9EasyAlarm®is simple. All you have to do is to program the calling numbers and connect the alarm unit
to the telephone line and power supply.
9EasyAlarm®verifies presence of a supervised person. If the optional motion-sensor is attached, an
alarm will be triggered if there is no activity (motion) detected with a free programmable period (Default
24 hours).
9EasyAlarm®protects your home/apartment. While you are absent, the optional motion detector can
trigger an alarm if someone enters your house or apartment. The optional smoke detector protect against
fire.
9EasyAlarm®monitors for noise activity. An alarm can be triggered, if the selected noise level in the
monitored room exceeds several times. The alarm is passed on without any indication to the person inside
the monitored room => listening-in connection (acoustical monitoring of patient/baby/children or home-
security application). If necessary a hands-free communication can be established.
9EasyAlarm®is comfortable. A handicapped person can answer an incoming call simply by pressing the
emergency button. Pressing the emergency button once again terminates the call. The volume of the hands-
free communication can be adjusted individually.
9EasyAlarm®is remote programmable. An authorised person can re-program the calling numbers and
the calling number sequence during phone connection.
Declaration of Conformity
According to the R&TTE Directive 1999/5/EC of 09.March 1999
Manufacturer’s Name: Leitronic AG
Manufacturer’s Address: Engeloostrasse 16
CH-5621 Zufikon, Switzerland
declares that the product
Product Name: EasyAlarm
Model Number: EA-8-EXT / EA-8-433
conforms to the following product specifications:
Safety (R&TTE, Article 3.1a): EN60950: 1992+A1+A2+A3+A4
EMC (R&TTE, Article 3.1b): EN 50081-1, 1992
EN 50082-1, 1997 Class B
Radio spectrum: EN 300 220 (EA-8-433 only)
ETS 300 683 (EA-8-433 only)
Telephone: CTR21 as specified in Council Decision 98/482/EC
Supplementary Information
The product herewith complies with the requirements of the following Directives and carries the CE marking
accordingly:
the EMC directive 89/336/EWG
the Low Voltage Directive 93/68/EEC
Zufikon, 1. April 2005 Silvan Tognella

4
2. SAFETY INSTRUCTIONS
2.1 Approval
EasyAlarm® is in compliance with R&TTE 1999/5/EC, Article 3.1a, 3.1b, 3.2 and is conform to the
following product specifications:
Safety: EN60950, 1992+A1+A2+A3+A4
EMC: EN 50081-1,1992
EN 50082-1, 1997 Class B
Telephone connection: CTR-21
Radio spectrum: EN 300 220 Class1 (EA-8-8433 only)
ETS 300 683 (EA-8-8433 only)
2.2 Telephone connection
EasyAlarm® must be connected to an analogue telephone line. Voltage of
this network (TVN=Telecommunication Network Voltage) is defined in
directive EN 41003. It is a telecommunication circuit that should not be
touched.
EasyAlarm® can be used in configuration with approved serial terminal equipment.
This equipment has been approved to [Council Decision 98/482/EC - "CTR 21"] for pan-European single
terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between
the individual PSTNs provided in different countries, the approval does not, of itself, give an unconditional
assurance of successful operation on every PSTN termination point. In the event of problems, you should
contact your equipment supplier in the first instance"
2.3 Wireless sensors
Approval Switzerland: BAKOM 99.0135.K.P (WT-201, WT-211)
Approval other countries according to description of wireless-sensors.
2.4 Power supply
A transformer according to the safety regulation EN60950 provides power supply. 9V battery is used as a back
up in case of power failure. It is located on the rear side oft the device.
2.5 Safety notes
Do not bring the device into contact with a liquid (water).
Do not open the device (exception: opening of battery compartment).
Replace the 9V-battery as soon as the announcement “battery error” is announced.
Please note: The telephone cord must be disconnected before opening the battery compartment
because otherwise you can get in contact with the telecommunication voltage!
Check alarm functions and start a test-call, before the system is put in service.
Check from time to time the range of the emergency button according to section 6.5
In case that EasyAlarm® is used to monitor children, the supervising person must be in a suitable
distance to take immediate care for the child.
The same as above applies to handicapped persons, EasyAlarm® is not a substitute of a personal
care taker!
Please note, an alarm by telephone is only successful if the alarmed party takes care of the following
points:
¦Alarm must not be answered by an answering machine or equal equipment
¦Mobile phones can be out of range (e.g. underground car park, shielded rooms, remote areas and
so on)
¦Take care of the charging condition of the mobile phone
¦Loud noise can prevent you from hearing the ringer
All the electrical connections have to be potential free. Observe the regulation according to EN60950.

5
3. SET VIEW / FUNCTION ELEMENTS
1.Function switch
Position Information
OFF Device is switched off
PROG Entering of calling numbers, calling number sequence, PIN-Code and further parameters
ON Device is in supervision mode
2.Selection switch
EasyAlarm® monitors the emergency buttons on all three positions (I/ II/ III). Additionally an acoustical
supervision (noise activity) can be activated according to section 6.6. Doing so, the selection switch is also used
to select the level of noise sensitivity:
Position Monitoring functions (Function switch on position ON)
I Low sensitivity => Alarm is triggered when noise level is exceeded frequently during a longer
period
II Medium sensitivity
III High sensitivity => Alarm is triggered if noise level is exceeded two or three times within a short
period
3.Keypad
When function switch is on position PROG, you can enter the calling numbers or do further programming. If
function switch is on position ON pressing any key will start a test call.
Keys are marked with 1 2 3 4 5 6 7 8 9 * 0 # in the following sections.
4.Loudspeaker
The integrated loudspeaker is used for voice guidance during the programming as well as for hands-free
communication during phone connection.
5.Microphone
Is used during hands-free connection and for recording of individual message.
6.LED
Status of LED Operation mode
Green Waiting period
Green brief flashing every 4 seconds, also if acoustical
monitoring is active by exceed set noise level Supervision mode activated
Green is on and off for 4 seconds alternatively Supervision mode deactivated
Orange Phone connection
7.Battery compartment
The 9V-battery is used as a backup during power failure.
Please note: The telephone cord must be disconnected before opening the battery
compartment because otherwise you can get in contact with the telecommunication
voltage!
8.Telephone jack (-LINE)
The plug must be locked in the jack. To disconnect press pawl.
9.External port (EXT/≂)for accessories (as motion sensor) and power supply.
6
1
5
4
3
2
-LINE
EXT/~
7
9
8

6
4. SETUP
4.1 Safety instructions
Function switch must be shifted to OFF and telephone-cord must be disconnected before any wiring
work is done on the AC-adapter or connecting cable.
All the electrical connections have to be potential free. Observe the regulation according to EN60950.
All contacts have to be protected against any body contact
Do not plug the phone cable (5) into the EXT/≂-jack, only into -line jack of alarm unit (1)!
4.2 Installation
1. Slide function switch to OFF
2. Insert 9V battery into compartment on rear side of alarm unit
Please note: The telephone cord must be disconnected before opening the battery compartment because
otherwise you can get in contact with the telecommunication voltage!
3. Connect cable of AC-adapter into one of the EXT-ports of the alarm unit and plug it into main socket
Operation with motion detector BBT-PIR-F (Option COMBI)
4. Mount the motion detector and connect the cable to the other EXT-port of the alarm unit
Details according to section 11.3 Telephone connection
5. Plug enclosed telephone-cord into -Line-Jack of alarm unit and connect it with the telephone network
¦If you share line with modem/telephone please proceed according to section 10.6
Program calling number(s) Details according to section 
6. Slide function switch to PROG
7. Enter * * <n> (selected calling number: Standard n= 1..9)
¦Corresponding calling number will be announced, followed by message “to modify press star“
8. Press * and enter calling number
9. Slide function switch to OFF
Select user language / record individual message Details according to section 6.3
10. Slide function switch to PROG
11. Enter *.*.#.
¦Current individual message will be announced followed by “to modify press * , to stop press # “
12. Select language for user announcements: (facultative)
Press key 1 for first user language or key 2 for second user language
13. Press * and start speaking
14. Press # to finish recording, max. duration is 12 seconds
¦New individual message will be announced. You can repeat steps 12 to 14 until text is fine!
15. Slide function switch to OFF
2
1
4
3

7
Program PIN-code Details according to section 6.4
16. Slide function switch to PROG
17. Press key #.=> You can prevent the alarm unit from unintended re-programming by pressing *..
18. Enter PIN-code (4 to 7 digits)
19. Press key #.
20. Re-enter PIN-code for confirmation
21. Press key #.= >New PIN-code will be announced
22. Slide function switch to OFF
Alarm unit is now ready for operation Details according to section 7
23. Slide selection switch to the requested position (I/II/III)
4.3 Operation with Plug&Protect-motion detector (EasyAlarm® SENIOR COMBI)
WALK-Test: Wait at least two minutes after power-up for the motion detector to be stabilised. After this time,
check the entire area by observing the LED. Adjust swivel if necessary.
4.3.1 Activation of the motion detector
EasyAlarm®detects the connected motion detector automatically at power-on (factory setting).
Warning:
By disconnecting the motion detector during operation, an alarm is triggered with the
announcement: „Emergency call due to sensor failure”!
By connecting the motion detector during operation, an alarm is triggered with the announcement:
„Emergency call activated, sensor 1 activated”!
4.3.2 Deactivation of the motion detector
If the motion detector is not connected during power-on, it is automatically deactivated.

8
5. WIRELESS EMERGENCY BUTTON
5.1 Introduction
9The WT-211 is a miniature waterproof wrist-worn transmitter, designed to send coded transmissions to the
EasyAlarm®.
9Pressing the pushbutton at the centre of the unit activates transmission.
9All WT-211 units are supplied with a wristband, to be worn like a regular watch.
9Operating power is obtained from a coin-type, 3-volt lithium battery that can last up to 10 years.
9A LED lights during transmission, indicating that battery voltage exceeds 2.7V.
9If the LED lights dimly or does not light at all during transmission, the battery must be replaced
immediately.
5.2 Technical Specifications
Frequency: 433,92 MHz
Coding: 8-bit DIP-switch (256 combinations)
Transmission time: approx. 2 seconds
Power supply: 3 V-Lithium-Battery (life time: 3-5 years by 3 usages per day)
Warning:
The transmission power is directly related to the power of the battery.
Temperature range: 0°Cto 50°C
Dimensions: 35 mm Ø
Weight: 25 g
Note: The transmitter is conforming to the local regulations. Note the following points:
A) Receivers may be blocked by radio signals occurring on or near their
operating frequencies, regardless of the code selected
B) A receiver can only respond to one transmitted signal at a time
C) Wireless equipment should be tested regularly (at least once a week)
to determine if there are sources of interference and to protect
against faults
5.3 Preparation for use
5.3.1 Installation of the battery
a) Open the WT-211 transmitter with a small Phillips screwdriver by removing
the 4 screws. Afterwards open the cover gently.
b) Remove the PCB carefully from the base of the housing.
c) Place the 3V-Lithium battery in such a way, that it is secured by the contact
spring Observe the polarity, „+“ side has to be on top.
d) Check the power of the battery by pressing the button in the centre of the
PCB. The LED must be lit to show a well-powered battery.
e) Place the PCB back into the housing. Observe the position pin to bring the
PCB into the correct position.
5.3.2 Coding
The WT-211 is equipped with an 8-pole DIP-switch (Code switch from 1-8) This switch is used to select the
code of the system. (see picture 4). Use a small screwdriver to select your code. ATTENTION: Do not use the
pre set code, as this one is only used to test the system. Do not use settings of placing all the switches on
position ON or OFF.
5.3.3 Assembling of the housing
Place the PCB into the main part, battery facing towards you. Observe the correct position given by the
positioning pin. Put the seal ring into the correct position and place the cover firmly. Tighten the 4 Phillips
screws gently.
5.4 Learn-in the wireless emergency button
The learn-in procedure is described in section 6.5.

9
6. PROGRAMMING
Important note:
All the programmed parameters remain stored even without battery.
You can prevent your system from unintended re-programming according to section 6.4.1. If you
use this protection feature message „programming deactivated, PIN“ will be announced when the
function switch is on position PROG.
Three beep: Mains power loss AND battery low at the same time!
6.1 How to program new calling numbers
EasyAlarm®supports nine calling numbers that can be programmed as follows:
1. Slide function switch to PROG
2. Enter * * <n> (selected calling number: Standard n= 1..9)
¦ Select number will be announced followed by “to modify press star“
3. If you like to change this calling number, press * , otherwise proceed with step 5
4. Enter new calling number. To delete an existing number enter * and proceed with step 5
5. Slide function switch to OFF
Notes:
Every keystroke will be acknowledged by a beep
Key #.programmes a dialling delay of 5 seconds, provided it is entered between two digits, e.g. a delay is
essential in a private exchange (first digit + #.+ calling number).
If your private exchange needs a flash pulse to start an internal call, following programming is possible:
2.#.followed by the extension number.
Key *.is used as separator for Point-ID protocol section 6.1.1.
If a programming error occurs, put function switch to OFF and repeat point 1 to 5.
Important notes:
Calling number 1 cannot be deleted due to safety reasons.
6.1.1 Point-ID (Contact-ID) alarm protocol
If the alarm should be transferred to a alarm organisation using the Point-ID (Contact-ID) protocol, the alarm
number has to be followed by key * and the customer-ID. EasyAlarm forwards the protocol to this alarm
number and connects hereafter to the following calling number in standard hands-free connection mode
Alarm number Customer-ID
074567890 34567
Example for programming the calling number: 0 7 4 5 6 7 8 9 0 * 3 4 5 6 .
Note:
The first character * , that follows the alarm number will not be transmitted (=> separator). The customer
ID is a four digit code. In case of an alarm the following codes are transmitted according to the <Alarm
reason> and the <Zone>.
Code <Alarm reason> <Zone>
602 Alarm due to cyclic test 900
602 Alarm due to remote programming "**#" 900
301 Alarm due to power failure 900
384 Alarm due to low battery of a radio sensor Radio zone 000..009
102 Alarm due to missing activity (presence verification) Radio zone 000..009
601 Alarm due to key-press (test-call) 900
132 Alarm due to noise monitoring 900
140 Alarm due to hardware sensor 1 901
140 Alarm due to hardware sensor 2 902
140 Alarm due to hardware sensor 3 903
140 Alarm due to radio sensor Radio zone 000..009
120 Alarm due to panic button Radio zone 000..009
120 Alarm due to emergency button Radio zone 000..009
111 Alarm due to fire sensor Radio zone 000..009

10
6.2 Designation of the calling number sequence
6.2.1 Standard sequence
Alarm triggered Calling number 1
Alarm not acknowledged
by called party 1
Calling number 2
alarm not acknowledged
by called party 2
same for calling number 3 to 9
The alarm is acknowledged by pressing DTMF 0 (section 7.6.5).
The alarm is passed to next party immediately by pressing DTMF 8 or after connection time-out.
6.2.2 How to program calling number sequence
1. Slide function switch to PROG
2. Enter * * 0.
¦Current calling number sequence will be announced followed by “to modify press * , to stop press # “
3. To maintain the current programming, go to point 5. Otherwise enter *..
4. Enter the desired sequence (max. 9 digits)
5. Slide function switch to OFF
Sample for programming calling number sequence:
a) ’123’ => calling number 1 will be dialled, followed by calling number 2, followed by calling number 3.
b) ’111133322’ => first calling number1 will be dialled (4 call attempts are made), followed by calling
number 3 (3 call attempts are made), followed by calling number 2 (with 2 call attempts).
Notes:
The calling number sequence is factory set to ‘123456789’, but a general reset according to section 10.1
will NOT RESET the calling number sequence!
In case of an un-programmed or deleted calling number, the calling number sequence will continue with the
next number of the sequence.
If a dialled number is busy and another call attempt is programmed, the waiting period before re-dialling is
30 sec.
If the calling number changes within the sequence, dialling of a new number starts without delay
6.3 How to select user language / How to record individual message
An individual announcement can be recorded as follows:
1. Shift function switch to PROG
2. Enter * * #.
¦Current individual message will be announced followed by “to modify press * , to stop press # “
3. Select language for user announcements: (facultative)
Press key 1 for first user language or key 2 for second user language
4. Press * and start speaking
5. Press # to finish recording, max. duration is 12 seconds
¦New individual message will be announced
6. Shift function switch to OFF
Notes:
Repeat step 3 and 5 until you are satisfied with individual message.
During recording the LED is lit.
6.3.1 Remote recording of individual message during handsfree connection
1. Enter DTMF * * # #
¦Current individual message will be announced followed by “to modify press * , to stop press # “
2. Start recording by sending DTMF * , start talking (max. 12 s) and finish by sending DTMF # .
¦New individual message will be announced
3. Wait until the message “Abort” confirms the end of the programming
Notes:
Repeat step 2 until you are satisfied with individual message.
Remote recording can be enabled / disabled according to section 10.8.1.
if called party 3 does not acknowledge the alarm, the calling
number sequence is repeated the number of programmed
alarm repetitions times (default value: two alarm
repetitions, programming see section 10.2)

11
6.4 How to program PIN-Code
You can change remote access PIN-code as follows:
1. Slide function switch to PROG
2. Press #.
¦You can prevent the alarm unit from unintended programming by pressing * .
3. Enter desired PIN-code (4 to 7 digits!) and press #.
4. Re-enter PIN-code for confirmation and press #.
¦If PIN-code is re-entered correctly it will be announced. If you selected program locking the
additional message „programming inactive: PIN” will be announced. In case of an incorrect
programming the message announced „Error“ will not be stored => old PIN-code remains active.
5. Slide function switch to OFF
6.4.1 Lock program mode
If you initiated programming new PIN-Code with key * the program mode is locked unless you unlock by re-
entering PIN-code. This feature prevents from unintentional reprogramming during operation.
6.4.2 Unlock program mode
Having the programming blocked as described in section 6.4.1, you can unlock as follows:
1. Slide function switch to PROG
¦Message „Programming inactive: PIN“ will be announced
2. Enter PIN-code and press #.
¦By entering correct PIN-code you will hear a confirmation beep, otherwise message „Error“
3. Slide function switch to OFF
6.5 How to learn-in wireless emergency button / Range check
If you want to learn-in a new emergency button you can proceed as follows:
1. Slide function switch to PROG
2. Enter *. *. *.
3. Press key 0. to 9. according to desired zone (->x)
4. Press key 0. to 9. according to transmitter type
¦Message announce „Zone x, to modify press * “
5. Press *.and start learn-in process according to the specified radio component.
¦A successful learn-in will be confirmed with a beep tone. By activating the transmitter again, a
loud beep tone will be generated as long you are within transmitting range. You can control this way
by reception range and to select the best suitable location of the unit.
6. Slide function switch to OFF
<n> Transmitter type/function
1 Smoke detector (=> Alarm with handsfree-connection)
7 Panic (=> un-delayed alarm with handsfree-connection => for listening-in connection see section 6.5.2)
Alarm can NOT be cancelled by pressing the emergency-button once again.
it is NOT possible to answer an incoming call by pressing the emergency-button!
8 Emergency call (=> Alarm with handsfree-connection)
Alarm can be cancelled by pressing the emergency-button once again during pre-warning period
it is possible to answer an incoming call by pressing the emergency-button!
* Wireless sensor for verifying presence of a supervised person (PIR or door contact)
#0 Deactivate zone
Note:
You can optimise location of alarm unit regarding the following points:
a) Place unit as far away from possible emitters
b) Do not place unit near a shielding cover
6.5.1 Check reception
You can check or optimise location of alarm unit as follows:
1. Slide function switch to PROG
2. Enter *. *. *. *. and press wireless button/sensor
¦Each time if you activate a learned-in sensor, the alarm unit announces its zone number. An
unknown sensor provokes a beep. Any other signal or noise will be passed directly to the
loudspeaker.
3. Slide function switch to OFF

12
6.5.2 Reaction on panic button
OFF ON
PROG
*. 9. 7. 1. 3 1 7 #. #.*.Value #.
OFF ON
PROG
Value Explanation
0 Silent alarm => listening-in connection
32 Un-delayed senior alarm => hands-free connection (=factory setting).
6.6 Alarm criteria’s according to the position of the selection switch I/II/III
EasyAlarm® monitors the emergency buttons on all three positions of the selection switch as well as the
optional attached motion detector checks for presence. But the acoustical monitoring of the room is deactivated.
(factory setting). This setting can be changed as follows:
A) Add up all the individual values according to your needs => Total= n.
Value Explanation
1 Acoustical monitoring is locked on position III (high sensitivity)
2 Acoustical monitoring is locked on position II (medium sensitivity)
4 Acoustical monitoring is locked on position I (low sensitivity)
8 Presence verification is locked on pos. III
16 Presence verification is locked on pos. II
32 Presence verification is locked on pos. I
*) If presence verification is locked, the motion sensor can be
activated as sensor-1-contact. In case of an activity (motion) an
alarm will be triggered (monitoring of the room or house
during your absence) => the total nmust be supplemented with
the symbol '*' see example below
Example: Monitored activities
Selection switch on I: Emergency button + presence control
Selection switch on II: Emergency button + presence control + acoustical monitoring
Selection switch on III: Emergency button + presence control + acoustical monitoring
=> Acoustical monitoring locked on position I
=> Presence verification locked on position III => instead of presence verification an alarm shall be
triggered if motion is detected => n= 4 + 8 + * = 12*
B) In case you would like to have an entry-delay for the sensor -1-contact, add following values:
Value v Explanation
0 Alarm due to sensor-1 without any delay (=factory setting)
64 Alarm due to sensor-1 is delayed
Example: Alarm due to sensor-1 shall be delayed => v= 64
C) Program the total value (s= v+ n= 64 + 12* = 76*) as follows:
1. Slide function switch to PROG
2. Enter *.
3. Enter 2.6.8.4.<s> (Example:2 6. 8. 4 7. 6. * )
4. Enter #.
5. Enter 2.6.8.4.<s> to confirm (Example: 2 6. 8. 4 7. 6. * )
6. Enter #.
¦ Correct => acknowledge beep ¦ Incorrect=> announcement „error“ => old value remains active.
7. Slide function switch to OFF
Notes:
In case of incorrect programming, Slide function switch to OFF and repeat step 1 to 7.
Factory setting: s= 7, no acoustical monitoring; presence verification is activated.
6.7 How to program presence verification time-out
Time-out for presence verification is factory set to 24h. If there is no activation within this period, an alarm is
triggered after a pre warning period of 10 minutes (this period is indicated with a periodical loud beep tone).
OFF
ON
PROG
*. 9. 7. 1. 3 6 7 #. #.*.Value #.
OFF ON
PROG
Value Explanation
0 Presence verification is switched off
6..255 Time-out in steps of 10 min. (min. 60min, max. 42.5h). Factory setting=144 (144*10min = 24 h)
Value
Value

13
7. OPERATION
7.1 Self check at power on
After power on the alarm unit checks battery, mains power and telephone-line conditions. If one of these tests
fails an appropriate message will be announced (battery error/power failure/line-check error).
Three beep: Mains power loss AND battery low at the same time!
Quickly handle the announce problem, otherwise the alarm functions are not guarantied.
7.1.1 Detection of wired sensor
EasyAlarm®detects the connected motion sensor automatically during the switching on procedure (factory
setting). This sensor is activated for presence verification
Attention:
By disconnecting the motion detector during operation, an alarm is triggered with the
announcement: „Emergency call due to sensor failure”!
By connecting the motion detector during operation, an alarm is triggered with the announcement:
„Emergency call activated, sensor 1 activated”!
7.2 Inactive waiting period
7.2.1 After power on or changing position of selection switch (exit delay)
EasyAlarm®remains inactive for 20 seconds (LED is on continuously), to leave time to quit your room/house
without triggering an alarm. An emergency call by pressing the emergency button is still possible.
Note:
The entry/exit period can be adjusted according to section 10.3.
If there are unacknowledged alarms, their quantity and the reason of the last alarm will be announced.
If presence verification is activated, following announcement is made: "sensor supervision activated".
Key Action
5.Announcement of the monitored functions (inactive waiting period will be restarted)
7.Bypass waiting period and change to inactive supervision mode
¦Attention: by switching from activated to inactivated supervision mode, an announcement of
the supervision modes is made and the waiting period starts again.
9.Bypass waiting period and change to active supervision mode
¦Attention: by switching from inactivated to activated supervision mode, an announcement of
the supervision mode is made and the waiting period starts again.
others Test-call will be made to the first calling number
7.2.1.1 Announcement of the supervision functions
The supervision functions can be activated or deactivated individually on each position of the selection switch
EasyAlarm®deactivated => announcement: "Supervision I/II/III deactivated"
EasyAlarm®activated => announcement: "Supervision I/II/III”
followed by the supervision mode of the activated type of monitoring:
acoustical monitoring => announcement: "due to noise"
sensor-1-monitoring => announcement: "due to sensor 1 activated”
7.2.2 ..after an successful alarm
EasyAlarm®remains inactive for two minutes (LED is on continuously) to avoid too many alarms due to
sensor contacts. An emergency call is still possible during this period. Any key-press results in a test call to the
first calling number.
7.3 Supervision mode
7.3.1 active supervision mode
In active supervision mode, the LED is flashing every 4 seconds. The LED is also lit, if the acoustical
monitoring is activated and the selected noise level is reached.
LED: acoustical monitoring inactive
LED: acoustical monitoring activated
LED: inactive mode
4 Sekunds 4 Sekunds
4 Sekunds 4 Sekunds
Noise
Nois

14
7.4 Alarm release
7.4.1 ..independent from state of arming (armed / disarmed)
Active byFactory set
alarm cause 1) I II III Entry delay Alarm connection Announce the alarm cause
Panic Instantaneously Listening-in “Emergency call activated”
Emergency 2)
   Delayed Hands-free “Emergency call activated”
Smoke
   Delayed Hands free “Alarm due to fire zone n”
Sensor 3 3)
   Instantaneously Listening-in “Alarm due to zone n”
1. Factory setting cause of alarm (user specific changes not mentioned)
2. An emergency call will be triggered, if the button has been activated for one second. After a pre alarm
period of 20 seconds the text “emergency call activated” is announced. A pre warning announcement is
used to avoid false alarms (i.e. technical error like power failure, unwanted emergency calls). During the
pre warning period the alarm can be cancelled by pressing the emergency button respectively by pressing
key 0.
3. Sensor 3 can be enabled as alarm sensor (NO or NC).
7.4.2 ..if system is armed only
Active byFactory set
alarm cause 1) I II III Entry delay
Alarm connection Announce the alarm cause
Sensor 1 4)
   Instantaneously Listening-in “Alarm due to sensor 1“
Presence verification 5)
   10 minutes/30 seconds Hands-free „Alarm due to presence
verification“
Sensor 2 6)
   Instantaneously Listening-in “Alarm due to sensor 2”
Noise 7)
   Instantaneously Listening-in “Alarm due to noise”
Power failure 8)
   Delay 1 min Hands-free “Alarm due to power failure”
4. Sensor 1 can also be used as a presence verification sensor (section 6.6)
5. If there is not motion detected within a period of 24 hours EasyAlarm®triggers an alarm, provided
programming is set to presence verification (section 6.7). Before starting the alarm there is a pre warning
period of ten minutes. If activation is detected (motion detected or emergency button pressed) within this
period, the alarm is triggered .
6. Sensor 2 can be enabled as alarm sensor (NO or NC).
7. Noise monitoring according to section 6.6: To avoid false alarm close windows and eliminate other noise
sources.
8. EasyAlarm® monitors mains voltage and triggers an alarm if power loss is longer than 10 to 20 minutes.
The mains power monitoring does not start if after power up the mains power is not detected. In this case
the message „power failure“ will be announced. After any mains power detection EasyAlarm®
automatically start power monitoring.
7.5 Alarm delay / Pre warning period / Entry delay
An alarm can be delayed due to following reasons:
9An alarm sensor in the area of the entrance must be delayed to have enough time to switch off the
supervision mode before EasyAlarm® dials the first calling number.
9A pre warning announcement is used to avoid false alarms (i.e. technical error like power failure, unwanted
emergency calls). During the pre warning period the alarm can be cancelled by pressing the emergency
button respectively by pressing key 0..
¦Announcement: „Alarm acknowledged“
Notes:
The entry/exit period can be adjusted according to section 10.3.
If an alarm has been triggered by pressing the emergency button, cancellation of the alarm is only possible,
if the button has been released for min. 3 seconds before pressing it again.
7.5.1 Siren activation during pre warning period
If you use a siren (section 11.1) which is activated as described in section 10.5.2, the pre alarm period is
signalled by a periodical siren tone.

15
7.6 Phone connection
The colour of the indicator LED changes to orange during telephone connection.
7.6.1 Time-out
There is a timer running in the phone connection mode. Phone connection is kept up for two minutes in case of
alarm call, and ten minutes in case of test call. Ten seconds before disconnection, the called person hears the
announcement “abort”. He/she can restart timer using DTMF 3 at any time.
7.6.2 Announcements
At the beginning of each phone connection the following information will be announced: Individual message
followed by the cause of alarm and the instruction to acknowledge alarm by pressing DMTF 0 . In a Listening-
in connection you get announcement: „to speak press 1“. This announcement is repeated every 8 seconds, until
a tone-dialling command is entered.
Notes:
At the beginning of any phone connection battery state will be checked and announced if low
The numbers of unacknowledged alarms is announced.
7.6.3 Listening-in connection
Possible tone-dialling commands during the listening-in connection
DTMF => Every valid command will be signalled
0 Terminate phone connection and acknowledge alarm
1 Switching to hands-free mode and restart connection time-out
2 Repeat announcements (Individual message / Cause of alarm)
3 Restart connection time-out (2 minutes)
4 Deactivate output (i.e. switching off alarm siren)
5 Announcement of current supervision mode as well as condition of the output
6 Activate output (i.e. switching on the alarm siren)
7 Change to inactive supervision mode (I, II, III) => monitoring for noise, sensor-1, mains failure and
presence verification inactive. Emergency call still possible.
8 Terminate phone connection without acknowledgment
9 Change to active supervision mode (I, II, III) => All monitoring functions re-activated
* * 0 Announcement of calling number sequence
* * nAnnouncement of calling number n(n: 1..9)
Following tone-dialling command can be used for remote programming, provided the programming is not
blocked (section 10.8)
* * # Trigger an alarm for test reasons ©Cause of alarm announcement "alarm due to programming"
* * n * followed by the new calling number announcement and change of calling number n
* * # # Record individual message => according to section 6.3.1.
7.6.3.1 Use of siren during listening in connection
The activation of a siren (section11.1) can be done either manually during a listening-in connection using
DTMF 6 or 4 or automatically in accordance to the reason of the alarm (programming section 10.5.2).
7.6.4 Hands-free connection
The commands during hands-free connection are identical to the commands during listening in connection,
except DTMF 1 .
Important note:
Hands-free connection must be terminated using DTMF 0 or 8 . Otherwise a busy tone signal
appears until phone connection is terminated due to time-out.
By selecting hands-free connection an activated siren (optionally) is automatically deactivated. If
requested, the siren can be activated or deactivated by DTMF 6 or 4 .
7.6.4.1 Adjustment of hands-free volume
During hands-free connection you can increase volume by pressing local key #.or decrease by pressing locale
key *.. Level can be adjusted in fifteen steps (1dB each) and remains stored.
7.6.5 Acknowledge alarm / Terminate connection
A called party can choose between acknowledgment by pressing DTMF 0 or passing on alarm to next party in
calling number sequence by pressing DTMF 8 .
Important notes:
There is no alarm repetition, if an alarm is triggered by pressing any key of the alarm unit (test call).
An alarm can be confirmed and terminated by pressing key 0.of the alarm unit or by pressing the
wireless emergency button for a second time.
If the alarm is programmed to a pager, the called person can confirm alarm during remote-access
after dialling-in.

16
7.7 Alarm repetition
If an alarm has not been acknowledged by passing all the calling numbers in the sequence, a number of alarm
repetitions can be programmed (programming 10.2). Factory setting: two alarm repetitions.
7.8 Test call
If alarm unit is switched to ON it is possible to start a test call as follows:
1. Select calling number by pressing key <n> (n=1. .. 9 )
¦Announcement: „Calling number <n>“ => If selected calling number is not programmed the
message “Error” will be announced and the first calling number will be dialled instead
2. Wait until hands-free connection is established and speak
3. Terminate phone connection by pressing 0.or slide function switch to OFF
Notes:
After two minutes phone connection will automatically terminate if called party does not give any tone-
dialling commands (i.e. called subscriber can disconnect using DTMF 0 or restart timer using DTMF 3 ).
During inactive waiting period after power on key 9.and 7.activate or deactivate the monitoring of the
supervision. Key 5.starts the announcement of the current supervision mode (section 7.3)
The volume of hands-free connection can be adjusted as described in section 7.6.4.1
7.9 Dialling-in (check call)
If the alarm unit is switched to ON you can dial in from any telephone set as follows:
1. Dial phone number of the EasyAlarm®
2. Let it ring for two ringing cycles and disconnect (hang up)
3. Redial after 20 seconds => EasyAlarm® answers call after two ringing cycles and waits for the PIN-Code
After entering the correct PIN-Code EasyAlarm® establishes a listening-in connection
¦Announcement „to stop press 0,to speak press 1“
If no tone-dialling command is entered, the phone connection will be terminated after two minutes connection
time-out. The supervised person can also terminate the phone connection by pressing the emergency button.
Important: In case that there are unconfirmed alarms, the quantity as well as the last reason of the alarm will be
announced! An unacknowledged alarm will be confirmed by entering DTMF 0 !
Notes:
The two-step dialling in procedure is for security reasons to avoid detecting of the alarm unit coincidently
by an unknown caller. Direct dialling in as well as other number of ringing cycles can be selected (
section 10.7)
If the PIN-code is incorrect or not entered within 15 seconds, EasyAlarm® disconnects after the
announcement „PIN error, abort“ => try again and enter correct PIN.
PIN-code is factory set to 9797. For safety reasons we recommend changing PIN-code and program your
individual code according to the manual.
If a successful dialling-in should be signalled with five gong-signals (to alert/inform the supervised person),
EasyAlarm® can be programmed according section 10.7.3.
7.10 Answering an incoming call
An incoming call, signalled by a parallel connected phone, can be answered as follows (Function switch ON):
7.10.1 ..by pressing the emergency button
a hands-free connection is established => Disconnect by pressing the emergency button once again.
7.10.2 ..by pressing any key of the alarm unit
a hands-free connection is established => Disconnect by pressing key 0.(section 10.7.4).

17
8. USEFUL NOTES
8.1 Tone-dialling command
If you want to use EasyAlarm® to its full potential a tone-dialling telephone is necessary. Nowadays most of
the telephones in use are working on tone dialling, also called DTMF or in-band signalling. Older telephones
are using pulse dialling. In case there is no tone-dialling telephone available, the features shown in section
7.6.3 cannot be used
Note:
An acoustic coupler can be purchased in electronic shops.
8.2 User information
8.2.1 Signals (beeps)
A single beep tone is used as a confirmation
Three beep: Mains power loss AND battery low at the same time!
8.2.2 Announcement audible in loudspeaker of EasyAlarm®
Announcement Message / Cause
„Individual message“ First message in case of an alarm
Abort Disconnection caused from the change of the position of the selection switch
Alarm acknowledged Disconnection
Alarm due to fire Alarm triggered by smoke sensor
Alarm due to presence
verification 24h without detection of movement
Alarm due to sensor
supervision Triggered emergency call due to loss of presence
Battery error Battery is low => battery test after power on
Calling number error First calling number in the calling number sequence is not programmed
Calling number nCalling number n (=1..9)
Calling number sequence Calling number sequence
Emergency call activated Emergency call, initiated by emergency button
Emergency call deactivated,
alarm acknowledged Emergency call confirmed
Error Incorrect programming => the old value remains stored
Line check error Telephone line check after power on was negative => dial tone missing
Output activated The output is activated after power on.
PIN Request to enter PIN-Codes by locked programme
Power failure Mains power missing => Mains power is tested after switching on the unit
Programming deactivated: PIN Request to enter PIN-Code to unlock programming
Sensor supervision activated Motion sensor is set to presence verification
Supervision (I/II/III) <due to
noise/sensor n> activated Announcement of the monitored alarm functions at current position of the
selection switch (I/II/III) triggered by pressing key 5 during the inactive
waiting period(section 7.2.1.1)
Supervision (I/II/III) activated Announcement in active supervision mode at current position of the
selection switch (I/II/III)
Supervision (I/II/III)
deactivated Announcement in active supervision mode at current position of the selection switch (I/II/III)
to modify press * , to stop
press # Recording of individual message
Unacknowledged alarms: nQuantity of unacknowledged alarms
8.2.3 Announcements audible in the handset of called subscriber
as well as during hands-free connection in loudspeaker of EasyAlarm®
Announcement Message / Cause
„Individual message” First message in case of an alarm or reaction on DTMF 2 .
Abort Phone connection will be terminated
Alarm due to fire Alarm triggered by smoke sensor
Alarm due to noise Alarm triggered by noise activity (Note: according to selection switch
position I,II,III the alarm can be delayed)
Alarm due to presence
verification 24h without detection of movement
Alarm due to programming A test call was initiated due to remote programming (section 0)
Alarm due to sensor nReason of alarm: alarm contact n.

18
sensor nactivated
sensor failure
sensor nis in alarm mode
disconnection of sensor during operation
Alarm due to sensor
supervision Triggered emergency call due to loss of presence
Battery error Battery is low => battery test before phone connection is established
Emergency call activated Emergency call, initiated by emergency button
Output <activated /
deactivated> confirmation of < DTMF 6 / DTMF 4 >
PIN Request to enter PIN-Code after dialling in (remote access)
PIN error, abort Wrong PIN-code => Phone connection terminated
Power failure Mains power loss => Mains power is tested every time before phone
connection is established
Programming acknowledged Successful remote programming of a calling number or calling number
sequence
Programming, abort Faulty remote programming of a calling number or calling number sequence
Sensor nactivated Announcement if sensor nis still in alarm mode
Supervision (I/II/III) < due to
noise / sensor n> activated Confirmation of DTMF 5 : announcement of the activated supervision
functions, indicating the supervision modes in accordance to the position of
the selection switch (I/II/III)
Supervision (I/II/III) activated Confirmation of DTMF 9 : Switch to active supervision mode an announce
monitoring functions at current position of the selection switch (I/II/III)
Supervision (I/II/III)
deactivated Confirmation of DTMF 7 : Switch to inactive supervision mode an
announce monitoring functions at current position of the selection switch
(I/II/III)
Unacknowledged alarms: nQuantity of unacknowledged alarms
8.3 Functional checks
8.3.1 Test-call
We strongly advise to make a test-call to check functionality of EasyAlarm® before starting operation.
8.3.2 Test alarm functions
Even though the alarm unit is maintenance free (except the battery) a periodical function test should be carried
out, especially:
Emergency button
Wired sensors
Acoustical monitoring
8.4 Battery check / replacement
If the announcement „Battery error“ is initiated after switching on EasyAlarm®, the battery should be
replaced immediately as follows:
1. Slide function switch to OFF
2. Disconnect EasyAlarm® from the telephone network, by removing the telephone cord
3. Open battery compartment and remove old battery
4. Insert new battery and close battery compartment
5. Reconnect telephone cord to EasyAlarm®
Notes:
Always use fresh 9V-batteries
Dispose the old battery properly
8.5 Maintenance
Slide function switch to OFF and remove telephone cord. Clean EasyAlarm® if necessary using a moistened
cloth and dry it afterwards.
Note:
Do not use cleaning agents or solvent

19
9. TROUBLE SHOOTING / ERROR HANDLING
Most problems can be checked and solved with help of the following chart. If the problem remains after
consulting this chart in details, please get in touch with your local dealer or contact the info line of your
country, see section 12.2
9.1 Telephone connection / Telephone communication
Symptoms Cause and /or remedy
LED is not lit after switching ON Replace battery
Announcement „programming
deactivated: PIN“ by an attempt of
reprogramming
Programming function is locked => to be unlocked according to
section 6.4.1
Announcement „Beep Beep Beep“
Announcement „battery error” Mains loss and low battery at the same time!
Battery is low => replace battery
Announcement „power failure” Power failure, transformer not connected
Announcement „line check error “
No dial tones are audible during test call
=> no tones are audible during the
dialling procedure
No dial tone has been detected:
Unit is not connected with the telephone network
Telephone network failure
Another telephone working on the same phone line is occupying
the line already
ÖPlug in telephone cord
ÖCheck the telephone cord
ÖStart test-call with different telephone
Test call does not call first calling
number in the calling number sequence:
Announcement „calling number error“
Calling number (n=2..9) is not programmed => Calling number
1 was dialled instead
Test call does not establish phone
connection: Announcement „calling
number n“ => dial tone audible
Calling number is wrong
Called party is not answering the phone
Remote access using dialling-in not
possible => EasyAlarm® is not
responding to the call
The dialling function is programmed for the two step modus (
section 10.7.2)
Remote access using dialling-in not
possible => disconnection after entering
of PIN-code
Wrong PIN-code entered => call again
EasyAlarm® does not react on tone-
dialling commands Current telephone does not support tone-dialling commands or has
not been configured => for example pulse dialling
9.2 Wireless emergency button
Symptom Cause and /or remedy
Activation of the emergency button does
not:
trigger alarm
terminate phone connection
Emergency button is not correctly configured or outside of range
(section 6.5)
External interference in the 433.92MHz-Band prevents a
reception
Battery of the emergency button is low => test battery or change
it according to separate instruction manual
Check location of transmitter/receiver according to section 6.5.1
9.3 Acoustical monitoring
Symptom Cause and /or remedy
noise is not triggering an alarm Factory setting supports monitoring of acoustics only on pos. III
of selection switch. (programming can be altered, see section
6.6)
The unit has been deactivated by DTMF 7 => LED
alternatively 4s on / 4s off
By switching on the unit or after triggering an alarm, the
acoustical monitoring is not active during the waiting time of 20
seconds (section 7.2) => LED is lit constantly during the
waiting time!
Depending on the position of the selection switch, an alarm is
triggered with a different delay. Every time the noise exceeds the
pre set level, the LED is on. (section 7.3.1)

20
9.4 Motion detector activated for presence verification
Symptom Cause and / or remedy
LED is on during WALK TEST, but no
alarm is triggered
In case of presence verification an alarm is only triggered, if no
motion has been detected over the programmed period (time-
out can be selected according to section 6.7)
WALK TEST has been set, but LED is
not on
Power supply of the motion detector is missing (=> check cable,
connector and power supply)
Power supply not on since two minutes (stabilize time of PIR-
motion detector)
Alarming with announcement
„emergency call activated, sensor 1
activated “
Motion detector has been connected after the unit has been
switch on!
Alarming with announcement
„emergency call activated, sensor failure
“
Motion detector has been disconnected after the unit has been
switch on!
9.5 Motion detector used as an alarm-sensor (sensor-1)
Symptom Cause and / or remedy
LED is on during WALK TEST, but no
alarm is triggered
Inactive waiting period by switching on the unit or between two
alarms is not expired
Supervision has been temporarily deactivated (deactivation)
Supervision is deactivated at current position of the selection
switch (I/II/III) (section 6.6)
Motion detection is programmed to verify presence (section
6.7), an alarm is only triggered if no motion is detected over a
programmed time.
WALK TEST has been set, but LED is
not on
Power supply of the motion detector is missing (=> check cable,
connector and power supply)
Power supply not on since two minutes (stabilize time of PIR-
motion detector)
There is no motion and the WALK
TEST LED is not on, but alarming with
periodical announcement „alarm sensor
n“ is spoken
Power supply of the motion detector is missing (check cable,
connector and power supply) => further announcement „power
failure “
The motion detector has been connected (additional
announcement „sensor 1 activated“ or disconnected (additional
announcement “sensor failure”) after power on => factory
setting automatically recognizes a connected Plug&Protect-
motion detector
„Alarm due to sensor n“ is announced,
but the motion detector has been
temporarily deactivated
The power supply of the unit has been cut off for a short period
The function switch has been switched to PROG or OFF after
temporarily deactivation.