Lenovo IdeaCentre K330B Parts list manual

Version 5.0 2011.03
Hardware Replacement Guide
IdeaCentre K3 Series
Machine type: 10062/7727
10073/1169
10066/7747
10067/7748
31048526
31048526 IC K3 HRG_FM_V5.0 (EN)(R).indd 1 2011-3-14 16:52:38

Hardware Replacement Guide
© Copyright Lenovo 2011. All rights reserved.
LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered
pursuant a General Services Administration “GSA” contract, use, reproduction,
or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925.
© 2011. Lenovo
31048526 IC K3 HRG V5.0 (EN)(R).indd 1 2011-3-14 17:34:09

Contents
Overview ..................................................................................... 1
Chapter 1 Locations ................................................................. 5
Locating components and connectors...........................................5
Identifying parts on the system board ..........................................10
Chapter 2 Replacing hardware.............................................. 15
General information......................................................................15
Removing the computer cover.....................................................15
Removing the front bezel .............................................................17
Replacing a memory module .......................................................18
Replacing the hard disk drive.......................................................19
Replacing an optical drive ............................................................20
Replacing the system fan assembly .............................................21
Replacing the heat sink assembly ................................................24
Replacing a PCI express adapter.................................................26
Replacing the CPU ......................................................................32
Replacing the keyboard ...............................................................35
Replacing the mouse ...................................................................36
Replacing the external speaker ....................................................37
Completing the installation ...........................................................37
Chapter 3 Appendix. ............................................................... 39
Declaration ..................................................................................39
Trademarks..................................................................................40
31048526 IC K3 HRG V5.0 (EN)(R).indd 2 2011-3-14 17:34:09

1
Hardware Replacement Guide
Overview
This guide is intended to be used by customers who are replacing Customer
Replaceable Units (CRUs) as well as trained service personnel who are replacing
Field Replaceable Units (FRUs). In this guide, CRUs and FRUs will often be referred
to as parts.
Note: Trained service personnel should refer to the Hardware Maintenance
Manual (HMM) for parts ordering information.
This guide does not include procedures for the replacement of all parts. It is
expected that trained service personnel are already able to replace cables, switches,
and certain mechanical parts without the need for step-by-step procedures.
Note: Use only parts provided by Lenovo®.
The description of the TV-Tuner card in this manual applies only to those computer
models that have the TV-Tuner card installed, and therefore does not apply to
models without a TV-Tuner card.
This guide contains instructions for replacing the following parts:
• Memorymodules
• Harddiskdrive
• Opticaldrive
• Heatsink,Fan
• CPU
• VGAcard
• Keyboard,Mouse(wired)
• Externalspeakers
Safety information for replacing CRUs
Do not open your computer or attempt any repairs before reading the “Important
safety information” in the Safety and Warranty Guide that was included with your
computer. An electronic copy of the Safety and Warranty Guide can also be
obtained online from the Lenovo® Support Web site at:
http://consumersupport.lenovo.com.
31048526 IC K3 HRG V5.0 (EN)(R).indd 1 2011-3-14 17:34:09

2Hardware Replacement Guide
Additional information resources
The most up-to-date information for your computer is available online at:
http://consumersupport.lenovo.com.
You can find the following information:
• CRUremovalandinstallation
• Publications
• Troubleshooting
• Parts
• Linkstootherusefulsourcesofinformation
Tools required
To disassemble the computer, you will need the following tools:
• Wristgroundingstrapandconductivematforpreventingelectrostatic
discharge
• Flatscrewdriver
• Phillipsscrewdriver
• Hexscrewdriver
• Plasticatscrewdriver
• Plastictweezers
Note: The screws used for the different components will vary in size. During
the disassembly procedure, group the screws with their corresponding
components to avoid a mismatch when replacing the components.
Handling static-sensitive devices
Static electricity, although harmless to you, can seriously damage computer
components.
When replacing a part, do not open the antistatic packaging containing the new
part until the defective part has been removed from the computer and you are
ready to install the new part.
31048526 IC K3 HRG V5.0 (EN)(R).indd 2 2011-3-14 17:34:09

3
Hardware Replacement Guide
When handling parts and other computer components, the following precautions
should be taken in order to avoid static electricity damage:
• Limityourmovements,assuchmovementscancausethebuild-upofstatic
electricity.
• Alwayshandlepartsandothercomputercomponentswithcare,including
handling adapters, memory modules, system boards, and microprocessors by
their edges. Never touch any exposed circuitry.
• Preventothersfromtouchingthepartsandothercomputercomponents.
• Beforereplacinganewpart,rstplacetheantistaticpackagingcontainingthe
part against a metal expansion slot cover or other unpainted metal surface on
the computer for at least two seconds. This will reduce static electricity in the
package and your body.
• Whenpossible,removethenewpartfromitsantistaticpackagingandinstallit
directly into the computer without setting the part down. If this is not possible,
placethepartontopofitsanti-staticpackagingonasmooth,atsurfaceprior
to installing it.
• Donotplacepartsonthecomputercoverorothermetalsurface.
31048526 IC K3 HRG V5.0 (EN)(R).indd 3 2011-3-14 17:34:09

4Hardware Replacement Guide
31048526 IC K3 HRG V5.0 (EN)(R).indd 4 2011-3-14 17:34:09

5
Hardware Replacement Guide
Locations
Chapter
This chapter provides illustrations to help you locate the various connectors,
controls and components in your computer. To remove the computer cover, refer
to the section in this manual entitled “Removing the computer cover”.
Locating components and connectors
The following illustrations will help you to locate the various components and
connectors in your computer.
Internal components
The following illustration shows the components inside your computer.
18
7
6
5
4
3
2
31048526 IC K3 HRG V5.0 (EN)(R).indd 5 2011-3-14 17:34:09

6Hardware Replacement Guide
Power supply PCI Express adapter card
System fan Memory modules
Microprocessor fan and heat sink Hard disk drive
PCI Express adapter connector Optical drive
Front view
The two following illustrations show the location of the connectors on the front of
the computer.
9
8
3
1
2
4
5
6
7
Power button
Power dial indicator ON/OFF
File backup button
USBconnector
Microphone connector
Headphone connector
Memory card reader (selected models only)
31048526 IC K3 HRG V5.0 (EN)(R).indd 6 2011-3-14 17:34:10

7
Hardware Replacement Guide
Optical drive (some models are equipped with only one optical drive)
Power dial switch
Rear view of the chassis
The following illustrations show the location of the connectors on the rear of the
computer.
IdeaCentre K330
Voltage selection switch (Selected models only)
Power connector
PS/2 keyboard connector
PS/2 mouse connector
USBconnectors(6)
eSATA connector
Ethernet connector
Audio connectors (6)
Standalone graphic card
Expansion card slots (Access connectors for any installed PCI express cards)
31048526 IC K3 HRG V5.0 (EN)(R).indd 7 2011-3-14 17:34:11

8Hardware Replacement Guide
IdeaCentre K330A/IedaCentre K330B
Voltage selection switch (Selected models only)
Power connector
PS/2 keyboard connector
PS/2 mouse connector
HDMI connector
USBconnectors(4)
On-board VGA connector
Ethernet connector
Audio connectors (3)
Standalone graphic card (Selected models only)
Expansion card slots (Access connectors for any installed PCI express cards)
31048526 IC K3 HRG V5.0 (EN)(R).indd 8 2011-3-14 17:34:11

9
Hardware Replacement Guide
IdeaCentre K335
Voltage selection switch (Selected models only)
Power connector
PS/2 keyboard connector
PS/2 mouse connector
eSATA connector
USBconnectors(6)
HDMI connector
On-board VGA connector
Ethernet connector
Audio connectors (6)
Standalone graphic card (Selected models only)
Expansion card slots (Access connectors for any installed PCI express cards)
31048526 IC K3 HRG V5.0 (EN)(R).indd 9 2011-3-14 17:34:11

10 Hardware Replacement Guide
Identifying parts on the system board
The system board (also known as the “mainboard” or “motherboard”) is the main
circuit board in your computer. It provides basic computer functions and supports
a variety of devices that are factory-installed or that you can install later.
The following illustrations show the locations of the different parts on the system
board.
IdeaCentre K330
Microprocessor and heat sink
Microprocessor fan connector
Memory connectors (4)
Thermal sensor header connector
Power connector
SATA connectors (4)
eSATA connector
31048526 IC K3 HRG V5.0 (EN)(R).indd 10 2011-3-14 17:34:12

11
Hardware Replacement Guide
Power fan connector
Front panel connector
FrontUSBconnectors(3)
Serial (com2) connector
Front audio connector
PCI express X 1 adapter connectors (2)
PCI express X 16 adapter connectors (2)
System fan connector
12V power connector
IdeaCentre K330A
Microprocessor and heat sink
Microprocessor fan connector
Memory connectors (4)
Thermal sensor header connector
31048526 IC K3 HRG V5.0 (EN)(R).indd 11 2011-3-14 17:34:12

12 Hardware Replacement Guide
Power connector
SATA connectors (4)
Front panel connector
FrontUSBconnectors(3)
Serial(com2) connector
Front audio connector
PCI express X 1 adapter connectors (3)
PCI express X 16 adapter connector
System fan connector
12V power connector
IdeaCentre K330B
Microprocessor and heat sink
Microprocessor fan connector
31048526 IC K3 HRG V5.0 (EN)(R).indd 12 2011-3-14 17:34:12

13
Hardware Replacement Guide
Memory connectors (2)
Thermal sensor header connector
Power connector
SATA connectors (4)
Front panel connector
FrontUSBconnectors(3)
Serial(com2) connector
Front audio connector
PCI express X 1 adapter connectors (3)
PCI express X 16 adapter connector
System fan connector
12V power connector
IdeaCentre K335
31048526 IC K3 HRG V5.0 (EN)(R).indd 13 2011-3-14 17:34:12

14 Hardware Replacement Guide
Microprocessor and heat sink
Microprocessor fan connector
Memory connectors (4)
Thermal sensor header connector
Power connector
SATA connectors (4)
eSATA connector
Power Fan connector
Front panel connector
FrontUSBconnectors(3)
Serial(com2) connector
Front audio connector
PCI express X 1 adapter connectors (2)
PCI express X 16 adapter connectors (2)
System fan connector
12V power connector
31048526 IC K3 HRG V5.0 (EN)(R).indd 14 2011-3-14 17:34:13

15
Hardware Replacement Guide
Attention:
Do not remove the computer cover or attempt any repair before reading the
“Important safety information” in the Safety and Warranty Guide that was
included with your computer or in the Hardware Maintenance Manual (HMM)
for the computer. To obtain copies of the Safety and Warranty Guide or
HMM, go to the Support Web site at http://consumersupport.lenovo.com.
Note: Use only parts provided by Lenovo.
General information
Pre-disassembly instructions
Beforeproceedingwiththedisassemblyprocedure,makesurethatyoudothe
following:
1. Turn off the power to the system and all peripherals.
2. Unplug all power and signal cables from the computer.
3. Placethesystemonaat,stablesurface.
Removing the computer cover
Attention:
Turn off the computer and wait 3 to 5 minutes to let the computer cool
before removing the computer cover.
To remove the computer cover:
1. Remove any media (diskettes, CDs, or memory cards) from the drives, shut
down the computer, and turn off all attached devices.
2. Unplug all power cords from electrical outlets.
Replacing hardware
Chapter
31048526 IC K3 HRG V5.0 (EN)(R).indd 15 2011-3-14 17:34:13

16 Hardware Replacement Guide
3. Disconnect all cables attached to the computer. This includes power cords,
input/output (I/O) cables, and any other cables that are connected to the
computer. Refer to “Locating connectors on the rear of the computer”.
4. Remove the two screws that secure the computer cover at the rear of the
chassis.
5. Slide the computer cover to the rear of the chassis to remove.
Note: For this procedure, it helps to lay the computer on its side.
31048526 IC K3 HRG V5.0 (EN)(R).indd 16 2011-3-14 17:34:13

17
Hardware Replacement Guide
Removing the front bezel
To remove the front bezel:
1. Remove the computer cover. Refer to “Removing the computer cover”.
Note: For this procedure, it helps to lay the computer on its side.
2. Remove the front bezel by releasing the three plastic tabs inside the chassis
and push the bezel outward as shown.
3. To reinstall the bezel, align the plastic tabs on the bottom of the bezel with the
corresponding holes in the chassis, and then snap it into position at the bottom
and top of the chassis.
4. Refer to the “Completing the installation”.
31048526 IC K3 HRG V5.0 (EN)(R).indd 17 2011-3-14 17:34:14