Lenovo 82YR000BGE User manual

Lenovo 13w Yoga Gen 2
Hardware Maintenance Manual

First Edition (February 2023)
© Copyright Lenovo 2023.
LIMITED AND RESTRI TED RIGHTS NOTI E: If data or software is delivered pursuant to a General Services
Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in ontract No. GS-
35F-05925.

Contents
About this manual . . . . . . . . . . . . iii
Chapter . Safety information . . . . . .
General safety . . . . . . . . . . . . . . . . 1
Electrical safety . . . . . . . . . . . . . . . . 1
Safety inspection guide . . . . . . . . . . . . . 3
Handling devices that are sensitive to electrostatic
discharge . . . . . . . . . . . . . . . . . . 3
Grounding requirements . . . . . . . . . . . . 4
Safety notices (multilingual translations) . . . . . . 4
Chapter 2. General checkout . . . . . 9
What to do first . . . . . . . . . . . . . . . 19
hecking the ac power adapter . . . . . . . . 20
hecking the battery and operational charging . . 20
Chapter 3. Locations . . . . . . . . . 23
Locating computer controls and connectors . . . 23
Front view . . . . . . . . . . . . . . . 23
Side view . . . . . . . . . . . . . . . 25
Locating FRUs and RUs . . . . . . . . . . . 26
Major FRUs and RUs . . . . . . . . . . 27
L D FRUs and RUs . . . . . . . . . . . 29
Miscellaneous parts . . . . . . . . . . . 30
Looking up FRU information . . . . . . . . . . 30
Chapter 4. FRU replacement
notices . . . . . . . . . . . . . . . . . 3
Service tool kit . . . . . . . . . . . . . . . 31
Screw notices . . . . . . . . . . . . . . . 31
Chapter 5. Removing or replacing a
FRU. . . . . . . . . . . . . . . . . . . 33
General guidelines. . . . . . . . . . . . . . 33
Before servicing the computer . . . . . . . . . 33
Disable Fast Startup and the built-in battery . . 33
Removing the nano-SIM-card and nano-SIM-
card tray (for selected models) . . . . . . . 34
Removing the SD card . . . . . . . . . . 34
Removing the pen dummy (for selected
models) . . . . . . . . . . . . . . . . 34
1010 Base cover assembly . . . . . . . . . . 35
1020 M.2 2242 solid-state drive . . . . . . . . 36
1030 Wireless WAN card (for selected models) . . 37
1040 oin-cell battery . . . . . . . . . . . . 38
1050 Memory module . . . . . . . . . . . . 38
1060 Wireless LAN card . . . . . . . . . . . 39
1070 Heat sink . . . . . . . . . . . . . . . 40
1080 Rear camera and microphone module,
bracket, and cable (for selected models) . . . . . 41
1090 Thermal fan . . . . . . . . . . . . . . 42
1100 Built-in battery . . . . . . . . . . . . . 43
1110 P-sensor cable (for selected models) . . . . 44
1120 Lenovo Integrated Pen charge board and
cable (for selected models) . . . . . . . . . . 45
1130 I/O brackets . . . . . . . . . . . . . . 46
1140 System board . . . . . . . . . . . . . 46
1150 Power button with or without fingerprint
reader . . . . . . . . . . . . . . . . . . 48
1160 Speaker assembly . . . . . . . . . . . 49
1170 Trackpad and trackpad cable . . . . . . . 50
1180 L D unit . . . . . . . . . . . . . . . 52
1190 Keyboard assembly . . . . . . . . . . . 53
2010 L D strip cover. . . . . . . . . . . . . 54
2020 Touch module assembly . . . . . . . . . 54
2030 L D cable. . . . . . . . . . . . . . . 56
2040 L D hinges . . . . . . . . . . . . . . 56
2050 amera and microphone module with
microphone rubbers . . . . . . . . . . . . . 57
2060 Gravity sensor board and camera cable . . . 58
2070 L D cover assembly. . . . . . . . . . . 59
Appendix A. Notices. . . . . . . . . . 6
Appendix B. Abbreviation table . . . . 63
© opyright Lenovo 2023 i

ii Lenovo 13w Yoga Gen 2 Hardware Maintenance Manual

About this manual
This manual contains service and reference information for the following products:
Product name Machine type (MT)
Lenovo 13w Yoga Gen 2 82YR and 82YS
Use this manual along with the advanced diagnostic tests to troubleshoot problems.
Important:
• This manual is intended only for trained service technicians who are familiar with products. Use this
manual along with the advanced diagnostic tests to troubleshoot problems effectively.
• Depending on the model, some hardware configuration and software programs might not be available on
the computer. Some statements in this manual might not be applicable to the computer.
• Before servicing a product, be sure to read all the information under hapter 1 “Safety information” on
page 1.
© opyright Lenovo 2023 iii

iv Lenovo 13w Yoga Gen 2 Hardware Maintenance Manual

Chapter . Safety information
This chapter presents following safety information that you need to be familiar with before you service a
notebook computer.
• “General safety” on page 1
• “Electrical safety” on page 1
• “Safety inspection guide” on page 3
• “Handling devices that are sensitive to electrostatic discharge” on page 3
• “Grounding requirements” on page 4
• “Safety notices (multilingual translations)” on page 4
General safety
Follow these rules to ensure general safety:
• Observe good housekeeping in the area of the machines during and after maintenance.
• When lifting any heavy object:
1. Ensure that you can stand safely without slipping.
2. Distribute the weight of the object equally between your feet.
3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift.
4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the
muscles in your back. Do not attempt to lift any object that weighs more than 16 kg (35 lb) or that you
think is too heavy for you.
• Do not perform any action that causes hazards to the customer, or that makes the equipment unsafe.
• Before you start the machine, ensure that other service technicians and the customer's personnel are not
in a hazardous position.
• Place removed covers and other parts in a safe place, away from all personnel, while you are servicing the
machine.
• Keep your tool case away from walk areas so that other people will not trip over it.
• Do not wear loose clothing that can be trapped in the moving parts of a machine. Ensure that your sleeves
are fastened or rolled up above your elbows. If your hair is long, fasten it.
• Insert the ends of your necktie or scarf inside clothing or fasten it with a nonconductive clip, about 8
centimeters (3 inches) from the end.
• Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your clothing, because metal
objects are good electrical conductors.
• Wear safety glasses when you are hammering, drilling, soldering, cutting wire, attaching springs, using
solvents, or working in any other conditions that might be hazardous to your eyes.
• After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device that
is worn or defective.
• Reinstall all covers correctly before returning the machine to the customer.
• Fan louvers on the machine help to prevent overheating of internal components. Do not obstruct fan
louvers or cover them with labels or stickers.
Electrical safety
Observe the following rules when working on electrical equipment.
© opyright Lenovo 2023

Important:
• Use only approved tools and test equipment. Some hand tools have handles covered with a soft material
that does not insulate you when working with live electrical currents.
• Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to
decrease electrostatic discharges (ESD). Do not use this type of mat to protect yourself from electrical
shock.
• Find the room emergency power-off (EPO) switch, disconnecting switch, or electrical outlet. If an electrical
accident occurs, you can then operate the switch or unplug the power cord quickly.
• Do not work alone under hazardous conditions or near equipment that has hazardous voltages.
• Disconnect all power before:
– Performing a mechanical inspection
– Working near power supplies
– Removing or installing main units
• Before you start to work on the machine, unplug the power cord. If you cannot unplug it, ask the customer
to power off the wall box that supplies power to the machine, and to lock the wall box in the off position.
• If you need to work on a machine that has exposed electrical circuits, observe the following precautions:
– Ensure that another person, familiar with the power-off controls, is near you. That person must be there
to switch off the power, if necessary.
– Use only one hand when working with powered-on electrical equipment; keep the other hand in your
pocket or behind your back.
CAUTION:
An electrical shock can occur only when there is a complete circuit. By observing the above rule,
you may prevent a current from passing through your body.
– When using testers, set the controls correctly and use the approved probe leads and accessories for
that tester.
– Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as
metal floor strips and machine frames.
Observe the special safety precautions when you work with very high voltages. Instructions for these
precautions are in the safety sections of maintenance information. Use extreme care when measuring high
voltages.
• Regularly inspect and maintain your electrical hand tools for safe operational condition.
• Do not use worn or broken tools and testers.
• Never assume that power has been disconnected from a circuit. First, check that it has been powered off.
• Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors,
nongrounded power extension cables, power surges, and missing safety grounds.
• Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is
conductive; such touching can cause personal injury and machine damage.
• Do not service the following parts with the power on:
– Power supply units
– Fans
– Units similar to those listed above
This practice ensures correct grounding of the units.
• If an electrical accident occurs:
– Use caution; do not become a victim yourself.
– Switch off power.
– Send another person to get medical aid.
2Lenovo 13w Yoga Gen 2 Hardware Maintenance Manual

Safety inspection guide
The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each
machine was designed and built, required safety items were installed to protect users and service
technicians from injury. This guide addresses only those items. You should use good judgment to identify
potential safety hazards due to attachment of non-Lenovo features or options not covered by this inspection
guide.
If any unsafe conditions are present, you must determine how serious the apparent hazard could be and
whether you can continue without first correcting the problem.
onsider these conditions and the safety hazards they present:
• Electrical hazards, especially primary power (primary voltage on the frame can cause serious or fatal
electrical shock)
• Explosive hazards, such as a damaged RT face or a bulging capacitor
• Mechanical hazards, such as loose or missing hardware
To determine whether there are any potentially unsafe conditions, use the following checklist at the
beginning of every service task. Begin the checks with the power off, and the power cord disconnected.
hecklist:
1. heck exterior covers for damage (loose, broken, or sharp edges).
2. Turn off the computer. Disconnect the power cord.
3. heck the power cord for:
a. A third-wire ground connector in good condition. Use a meter to measure third-wire ground
continuity for 0.1 ohm or less between the external ground pin and the frame ground.
b. The power cord should be the authorized type specified for your computer. Go to: https://
support.lenovo.com/partslookup.
c. Insulation must not be frayed or worn.
4. heck for cracked or bulging batteries.
5. Remove the cover.
6. heck for any obvious non-Lenovo alterations. Use good judgment as to the safety of any non-Lenovo
alterations.
7. heck inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or
other liquids, or signs of fire or smoke damage.
8. heck for worn, frayed, or pinched cables.
9. heck that the power-supply cover fasteners (screws or rivets) have not been removed or tampered
with.
Handling devices that are sensitive to electrostatic discharge
Any computer part containing transistors or integrated circuits (I s) should be considered sensitive to
electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between objects.
Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the
person handling the part are all at the same charge.
Notes:
1. Use product-specific ESD procedures when they exceed the requirements noted here.
hapter 1.Safety information 3

2. Ensure that the ESD protective devices you use have been certified (ISO 9000) as fully effective.
When handling ESD-sensitive parts:
• Keep the parts in protective packages until they are inserted into the product.
• Avoid contact with other people.
• Wear a grounded wrist strap against your skin to eliminate static on your body.
• Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when
you are wearing a wrist strap.
• Use a grounded work mat to provide a static-free work surface. The mat is especially useful when
handling ESD-sensitive devices.
• Select a grounding system, such as those listed below, to provide protection that meets the specific
service requirement.
Note: The use of a grounding system to guard against ESD damage is desirable but not necessary.
– Attach the ESD ground clip to any frame ground, ground braid, or green-wire ground.
– When working on a double-insulated or battery-operated system, use an ESD common ground or
reference point. You can use coax or connector-outside shells on these systems.
– Use the round ground prong of the ac plug on ac-operated computers.
Grounding requirements
Electrical grounding of the computer is required for operator safety and correct system function. Proper
grounding of the electrical outlet can be verified by a certified electrician.
Safety notices (multilingual translations)
The safety notices in this section are provided in the following languages:
• English
• Arabic
• Brazilian Portuguese
• French
• German
• Hebrew
• Japanese
• Korean
• Spanish
• Traditional hinese
DANGER
4Lenovo 13w Yoga Gen 2 Hardware Maintenance Manual

DANGER
DANGER
DANGER
DANGER
DANGER
DANGER
hapter 1.Safety information 5

DANGER
6Lenovo 13w Yoga Gen 2 Hardware Maintenance Manual

PERIGO
PERIGO
PERIGO
hapter 1.Safety information 7

PERIGO
PERIGO
PERIGO
PERIGO
PERIGO
DANGER
DANGER
8Lenovo 13w Yoga Gen 2 Hardware Maintenance Manual

DANGER
DANGER
DANGER
DANGER
DANGER
hapter 1.Safety information 9

DANGER
VORSICHT
VORSICHT
VORSICHT
VORSICHT
0 Lenovo 13w Yoga Gen 2 Hardware Maintenance Manual

VORSICHT
VORSICHT
VORSICHT
VORSICHT
hapter 1.Safety information

2 Lenovo 13w Yoga Gen 2 Hardware Maintenance Manual

hapter 1.Safety information 3

4 Lenovo 13w Yoga Gen 2 Hardware Maintenance Manual