Lenovo ThinkSystem DE Series User manual

ThinkSystem DE Series
Installing DE6400 and DE6600
Machine Types: DE6400 (7DB6) and DE6600 (7DB7)

First edition (December 2022)
© Copyright Lenovo 2022.
L M TED AND RESTR CTED R GHTS NOT CE: f data or software is delivered pursuant to a General Services
Administration (GSA) contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No.
GS-35F-05925

Contents
1. Install and set up DE6400 and DE6600 storage systems 1
2. Install and set up DE6400 and DE6600 storage systems 2
2.1. Install process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê2
2.2. Prepare for installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê4
2.3. Install the hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê6
2.4. Power the controller shelves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê9
2.5. Complete storage system setup and configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê10
2.5.1. Step 1: Cable the data hosts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê10
Option 1: Direct-attach topology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê10
Option 2: Fabric topology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê11
2.5.2. Step 2: Connect and configure the management connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê11
Option 1: DHCP server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê11
Option 2: Static IP address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê12
2.5.3. Step 3: Configure storage system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê14
3. Appendix 15
3.1. General Practice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê15
3.2. Contacting support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê15
3.3. Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê15
3.4. Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê16

Chapter 1. Install and set up DE6400 and DE6600 storage
systems
Learn how to install and set up the DE6400 or DE6600 storage system.
You can choose one of the following formats to guide you through installing and setting up your
new storage system.
•PDF
This is a PDF poster of step-by-step instructions with live links to additional content.
•Online instructions
These are the online setup instructions described on this site. Start with Prepare for installation
to get started.
1

Chapter 2. Install and set up DE6400 and DE6600 storage
systems
2.1. Install process
Before you install and set up your new storage system, familiarize yourself with
the installation process:
2

Direct-attach
or
Fabric?
Complete
system setup and
configuration
Direct-attach
topology
Fabrictopology
Management
Port Configuration
with Static IPAddress
Management port
configuration with DHCP
Connect and configure
the management
connection
After installing the
hardware
Prepare for installation
Receive, unpack, and
inventory equipment
Contact customer
supportto receive
missing items
Do I have
everything I
ordered?
No
Yes
Install hardware
Cable the data hosts
based onyour
network type
Power the
controller shelves
Complete storage
system setup and
configuration
3

2.2. Prepare for installation
Learn how to prepare for installation of your DE6400 or DE6600 series storage
system.
Before you begin
If you are cabling your DE6400 and DE6600 for SAS expansion, review the following information:
•Add SAS expansion cards for SAS expansion card installation.
•Cabling overview for SAS expansion cabling.
Steps
1. Create an account and register your hardware at Lenovo Data Center Support.
2. Ensure that the following items are in the box that you received.
Shelf with drives installed (end caps packaged
separately)
Rack-mount hardware
The following table identifies the types of cables you might receive. If you receive a cable not
listed in the table, see Lenovo Press to locate the cable and identify its use.
Connector type Cable type Use
RJ-45 Ethernet cables (if
ordered)
Management connection
4

Connector type Cable type Use
I/O cables (if ordered) Cabling the data hosts
Power cables (if ordered) Powering up the storage
system
3. Ensure that you provide the following items.
Phillips #2 screwdriver
Flashlight
ESD strap
5

2U rack space: A standard 19 in. (48.30 cm)
rack to fit 2U shelves of the following
dimensions.
Depth: 19.0 in. (48.3 cm)
Width: 17.6 in. (44.7 cm)
Height: 3.34 in. (8.48 cm)
Shelf: 24-drive
Max Weight: 60.5 lb (27.4 kg)

Using third-party cabinets
might cause the power
cables to restrict access to
the controller.
A supported browser for the management
software:
•Google Chrome (version 78 and later)
•Microsoft Internet Explorer (version 11 and
later)
•Microsoft Edge (88 and later)
•Mozilla Firefox (version 70 and later)
•Safari (version 12 and later)
2.3. Install the hardware
You can install a DE6400 or DE6600 storage system in a two-post rack or a
Lenovo system cabinet.
Before you begin
Before you install a DE6400 or DE6600 storage system, make sure you do the following:
•Register your hardware at Lenovo Data Center Support.
•Prepare a flat, static-free work area.
•Take anti-static precautions.
Steps
6

1. Unpack the hardware.
a. Unpack the contents and inventory the contained hardware against the packing slip.
b. Before proceeding, read through all the instructions.
2. Install the rails.
To prevent the equipment from toppling over, install the hardware from the
bottom of the rack or cabinet up to the top.
If instructions were included with your rack-mounting hardware, refer to them to learn how to
install the rails. For additional rack-mounting instructions, see Rack-mount hardware.
3. Install the shelf.
a. If you are installing multiple shelves, begin installing from the bottom to the top of the
cabinet. Position the back of the shelf onto the rails.
When installing the shelf, use a team-lift with two people.
b. Supporting the shelf from the bottom, slide it into the cabinet.
7

4. Secure the shelf.
For more information, see Rack-mount hardware.
8

2.4. Power the controller shelves
Learn how to attach the power cables and power on the drive shelves.
Before you begin
Before you power the controller shelves, make sure to do the following:
•Install your hardware.
•Take anti-static precautions.
Steps
1. Plug in the power cables, one to each controller ( pictured below).
Power cables
9

2. Connect the two power cables, one from each controller, to two separate power distribution
units (PDUs) in the cabinet or rack.
Accessing a DE6400 or DE6600 controller canister from the shelf can be
blocked by third-party PDUs. Do not use power outlets directly behind the
controller canister.
3. Allow the controller to boot for five minutes before completing the storage system set up and
configuration.
Result
The controller boots automatically. The LEDs flash on and the fans start to indicate that the
controller is powering on.
Fans are very loud when they first power on.
2.5. Complete storage system setup and configuration
Learn how to connect the controller cables to your network, and then complete
the setup and configuration.
2.5.1. Step 1: Cable the data hosts
Cable the storage system according to your network topology.
Option 1: Direct-attach topology
The following example shows cabling to the data hosts using a direct-attach topology.
Table 1. Example A: Direct-attach topology
10

1. Connect each host adapter directly to the
host ports on the controllers.
Option 2: Fabric topology
The following example shows cabling to the data hosts using a fabric topology.
Table 2. Example B: Fabric topology
1. Connect each host adapter directly to the
switch.
2. Connect each switch directly to the host
ports on the controllers.
2.5.2. Step 2: Connect and configure the management connection
You can configure the controller management ports using a DHCP server or a static IP address.
Option 1: DHCP server
Learn how to configure the management ports with a DHCP server.
Before you begin
•Configure your DHCP server to associate an IP address, subnet mask, and gateway address as
a permanent lease for each controller.
•Obtain the assigned IP addresses you will use to connect to the storage system from your
network administrator.
Steps
1. Connect an Ethernet cable to each controller’s management port, and connect the other end to
your network.
11

RJ-45 Ethernet cables (if ordered)
The following figure shows an example of the controller’s management port location ( shown):
2. Open a browser and connect to the storage system using one of the controller IP addresses
provided to you by your network administrator.
Option 2: Static IP address
Learn how to configure the management ports manually by entering the IP address and the subnet
mask.
Before you begin
•Obtain the controllers’ IP address, subnet mask, gateway address, and DNS and NTP server
information from your network administrator.
•Make sure that the laptop you are using is not receiving network configuration from a DHCP
server.
Steps
1. Using an Ethernet cable, connect controller A’s management port to the Ethernet port on a
laptop.
Controller A is the upper controller canister, and controller B is the lower
controller canister.
RJ-45 Ethernet cables (if ordered)
12

The following figure shows an example of the controller’s management port location ( shown):
2. Open a browser and use the default IP address (169.254.128.101) to establish a connection to
the controller. The controller sends back a self-signed certificate. The browser informs you that
the connection is not secure.
3. Follow the browser’s instructions to proceed and launch ThinkSystem System Manager.
If you are unable to establish a connection, verify that you are not receiving
network configuration from a DHCP server.
4. Set the storage system’s password to login.
5. Use the network settings provided by your network administrator in the Configure Network
Settings wizard to configure controller A’s network settings, and then select Finish.
Because you reset the IP address, System Manager loses connection to the
controller.
6. Disconnect your laptop from the storage system, and connect the management port on
controller A to your network.
7. Open a browser on a computer connected to your network, and enter controller A’s newly
configured IP address.
If you lose the connection to controller A, you can connect an ethernet cable
to controller B to reestablish connection to controller A through controller B
(169.254.128.102).
8. Log in using the password you set previously.
The Configure Network Settings wizard will appear.
9. Use the network settings provided by your network administrator in the Configure Network
Settings wizard to configure controller B’s network settings, and then select Finish.
13

10. Connect controller B to your network.
11. Validate controller B’s network settings by entering controller B’s configured IP address in a
browser.
If you lose the connection to controller B, you can use your previously
validated connection to controller A to reestablish connection to controller B
through controller A.
2.5.3. Step 3: Configure storage system
After you have installed the DE6400 or DE6600 hardware, use the System Manager to configure
and manage your storage system.
Before You Begin
•Configure your management ports.
•Verify and record your password and IP addresses.
Steps
1. Connect your controller to a web browser.
2. Use ThinkSystem System Manager to manage your DE6400 or DE6600 series storage system.
Refer to the online help included with System Manager.
For accessing System Manager, use the same
IP addresses that you used to configure your
management ports.
If you are cabling your DE6400 and DE6600 for SAS expansion, see Maintaining Hardware for SAS
expansion card installation and the Cabling DE-Series hardware for SAS expansion cabling.
14

Chapter 3. Appendix
3.1. General Practice
For expected performance, check the link for details: Checks to perform when experiencing slower
than expected VMware performance.
Check the latest firmware on Lenovo DCG Storage Firmware Update Page.
3.2. Contacting support
You can contact Support to obtain help for your issue.
You can receive hardware service through a Lenovo Authorized Service Provider. To locate a
service provider authorized by Lenovo to provide warranty service, go to
https://datacentersupport.lenovo.com/serviceprovider and use filter searching for different
countries. For Lenovo support telephone numbers, see
https://datacentersupport.lenovo.com/supportphonelist for your region support details.
3.3. Notices
Lenovo may not offer the products, services, or features discussed in this
document in all countries. Consult your local Lenovo representative for
information on the products and services currently available in your area.
Any reference to a Lenovo product, program, or service is not intended to state or imply that only
that Lenovo product, program, or service may be used. Any functionally equivalent product,
program, or service that does not infringe any Lenovo intellectual property right may be used
instead. However, it is the user’s responsibility to evaluate and verify the operation of any other
product, program, or service.
Lenovo may have patents or pending patent applications covering subject matter described in this
document. The furnishing of this document is not an offer and does not provide a license under any
patents or patent applications. You can send inquiries in writing to the following:
Lenovo (United States), Inc.
8001 Development Drive
Morrisville, NC 27560
U.S.A.
Attention: Lenovo Director of Licensing
LENOVO PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some
jurisdictions do not allow disclaimer of express or implied warranties in certain transactions,
therefore, this statement may not apply to you.
15

This information could include technical inaccuracies or typographical errors. Changes are
periodically made to the information herein; these changes will be incorporated in new editions of
the publication. Lenovo may make improvements and/or changes in the product(s) and/or the
program(s) described in this publication at any time without notice.
The products described in this document are not intended for use in implantation or other life
support applications where malfunction may result in injury or death to persons. The information
contained in this document does not affect or change Lenovo product specifications or warranties.
Nothing in this document shall operate as an express or implied license or indemnity under the
intellectual property rights of Lenovo or third parties. All information contained in this document
was obtained in specific environments and is presented as an illustration. The result obtained in
other operating environments may vary.
Lenovo may use or distribute any of the information you supply in any way it believes appropriate
without incurring any obligation to you.
Any references in this publication to non-Lenovo Web sites are provided for convenience only and
do not in any manner serve as an endorsement of those Web sites. The materials at those Web
sites are not part of the materials for this Lenovo product, and use of those Web sites is at your
own risk.
Any performance data contained herein was determined in a controlled environment. Therefore, the
result obtained in other operating environments may vary significantly. Some measurements may
have been made on development-level systems and there is no guarantee that these
measurements will be the same on generally available systems. Furthermore, some measurements
may have been estimated through extrapolation. Actual results may vary. Users of this document
should verify the applicable data for their specific environment.
3.4. Trademarks
LENOVO, LENOVO logo, and THINKSYSTEM are trademarks of Lenovo. All
other trademarks are the property of their respective owners. © 2022 Lenovo.
16