Leonton RPG5-2602-2C Instructions for use

⚫RPG5-2602-2C
⚫RPG5-2602-2C-T
⚫-T

© Copyright 2021 Leonton Technologies Co., Ltd. All Rights Reserved
This document contains information, which is protected by copyright. Reproduction, adaptation or
translation without prior permission is prohibited, except as allowed under the copyright laws.
Disclaimer
Leonton Technologies, Co. Ltd. provides this manual without warranty of any kind, expressed or
implied, including but not limited to the implied warranties of merchantability and fitness for a
particular purpose. Leonton Technologies, Co. Ltd. may make improvements and/or changes to the
product and/or specifications of the product described in this manual, without prior notice.
Leonton Technologies, Co. Ltd. will not be liable for any technical inaccuracies or typographical
errors found in this guide. Changes are periodically made to the information contained herein and
will be incorporated into later versions of the manual. The information contained is subject to
change without prior notice.

FCC Notice
This equipment has been tested and found to comply with the limits for a Class-A digital device, pursuant
to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy. It may cause harmful interference to radio communications if the equipment is not installed and
used in accordance with the instructions. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
⚫Reorient or relocate the receiving antenna.
⚫Increase the separation between the equipment and receiver.
⚫Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
⚫Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications not expressly approved by the grantee of this device could void
the user's authority to operate the equipment.
Déclaration FCC
Cet équipement a été testé et reconnu conforme aux limites de la classe A pour les équipements
numériques, conformément à la section 15 des Réglementations FCC. Ces limites sont conçues pour fournir
une protection raisonnable contre toutes interférences nuisibles dans un milieu résidentiel. Cet
équipement génère, utilise, et peut émettre de l’énergie de fréquence radio et, s’il n’est pas installé et
utilisé conformément au manuel d’instruction, peut perturber la réception radio. Cependant, il n’est pas
garanti que l’équipement ne produira aucune interférence dans une installation particulière. Si cet
équipement cause des interférences nuisibles à la réception radio ou télévisée, qui peuvent être
déterminées en l’éteignant et le rallumant, l’utilisateur est encouragé à essayer de remédier au problème
en prenant les mesures suivantes:
⚫Réorienter ou déplacer l’antenne réceptrice.
⚫Augmenter la distance entre l’équipement et le récepteur.
⚫Connecter l’équipement à une prise secteur sur un circuit différent de celui utilisé par le récepteur.
⚫Consulter le négociant ou un technicien radio/TV expérimenté.
Attention: Tout changement ou modification non expressément approuvé par le concessionnaire de cet
appareil pourrait annuler l'autorité de l'utilisateur à utiliser l'équipement.
CE Mark Warning
This is a Class-A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
CE Mark Avertissement
Ceci est un produit de classe A. Dans un environnement domestique, ce produit peut être utilisé en
présence d'interférences radio.
This document is the current official release manual. Please check our website (www.leonton.com) for
any updated manual or contact us by e-mail ([e-mail]).

CONTENT
OVERVIEW ................................................................................................................................... 1
Key Features.................................................................................................................................................................1
Package Contents.......................................................................................................................................................2
Safety Precaution........................................................................................................................................................2
HARDWARE DESCRIPTION...................................................................................................... 3
Physical Dimensions ..................................................................................................................................................3
Front Panel....................................................................................................................................................................4
LED Indicators..............................................................................................................................................................5
Ethernet Ports..............................................................................................................................................................6
Cabling...........................................................................................................................................................................7
Wiring the Power Inputs...........................................................................................................................................9
Wiring the Fault Alarm Contact ..............................................................................................................................9
Grounding Note........................................................................................................................................................10
MOUNTING INSTALLATION..................................................................................................11
Rack Mounting ..........................................................................................................................................................11
HARDWARE INSTALLATION..................................................................................................12
Installation Steps ......................................................................................................................................................12
TROUBLE SHOOTING ..............................................................................................................14

1
OVERVIEW
This series is rated IP40 and Rack-Mounting installation. Each unit of this industrial gigabit managed
Ethernet switch series has 24*10/100/1000Tx with IEEE 802.3at compliant ports (30W/port) and 2 Gigabit
combo ports (2*10/100/1000Tx RJ45 or 2*100/1000 SFP slots), suitable for applications that require high
bandwidth and long-distance communication.
In order to prevent unregulated voltage, this series provides high EFT and ESD protection. This also allows
it to function in harsh environments, as well as support power redundancy with a dual power input design
with reverse polarity protection. The built-in relay warning function alerts users about occurring power
failures.
With one model having an operating temperature of -10 to 65°C and another with a wide operating
temperature of -40 to 75°C, this series is designed to meet any needs in industrial automation, outdoor
application and harsh environments.
Key Features
Interface & Performance
⚫All copper ports support auto MDI/MDI-X function
⚫Embedded 24*10/100/1000Tx (PSE 30W/Port) and 2*gigabit combo ports (2*10/100/1000Tx copper
ports or 2*100/1000 SFP Slots)
⚫Store-and-forward switching architecture
⚫8K MAC Address Table
⚫Supports 9.6Kbytes Jumbo Frame
⚫4Mbits memory buffer
Power Input
⚫Dual 48-55VDC redundant power inputs with connective 8-pin terminal block
⚫Max. current 15.5A
⚫Max. PoE output: 720W
⚫Relay Contact: 24 VDC, 1A resistive
⚫The power input specification is complied with the requirements of SELV (Safety Extra Low Voltage),
and the power supply should be complied with UL 61010-1 & UL 61010-2-201
Certification
⚫CE/FCC
⚫UL 61010-1
⚫UL 61010-2-201
Operating Temperature
⚫Standard operating temperature model: -10°C ~ 65°C
⚫Extended operating temperature model (–T): -40°C ~ 75°C
Case/Installation
⚫IP40 protection
⚫Rack-mount design
⚫Installation in a pollution degree 2 industrial environment
⚫Standalone Installation

2
Package Contents
⚫1 –RPG5-2602-2C(-T) - Unit weight: 2.82kg (6.22 lb), Shipping weight: 3.54kg (7.80 lb)
⚫2 –Rack-mounting brackets and screws
⚫1 –Quick installation guide
⚫1 –RJ45 to DB9 Serial Console cable
Safety Precaution
Attention
If the DC voltage is supplied by an external circuit, please use a protection device on the power supply input.
Supply by UL Listed industrial use power. The industrial Ethernet switch’s hardware specs, ports, cabling
information, and wiring installation will be described within this user manual.
Attention
Si la tension CC est fournie par un circuit externe, veuillez utiliser un dispositif de protection sur l'entrée
d'alimentation. Fourniture par courant industriel homologué UL. Les spécifications matérielles, les ports, les
informations de câblage et l'installation du câblage du convertisseur de média industriel seront décrits dans
ce manuel d'utilisation.
Warning Labels
The caution label means that you should check the certain information on user manual when working with
the device. (Shown in Figure 1.1)
Étiquettes d'avertissement
L'étiquette d'avertissement signifie que vous devez vérifier certaines informations sur le manuel d'utilisation
lorsque vous travaillez avec l'appareil. (Montré dans la Figure 1.2)
Figure 1.1 - Caution Label
Figure 1.1 - Étiquette de mise en garde
Figure 1.2 - Hot Surface Warning Label
Figure 1.2 - Étiquette d'avertissement de surface chaude

3
HARDWARE DESCRIPTION
Physical Dimensions
Figure 2.1, below, shows the physical dimensions of RPG5-2602-2C series.
(W x H x D) is 440mm x 44mm x 200mm
Figure 2.1: Physical Dimensions

4
Front Panel
The front panel of the RPG5-2602-2C series industrial gigabit managed ethernet switch is shown below in
Figure 2.2.
Figure 2.2: The Front Panel of RPG5-2602-2C Series
Rear Panel
Figure 2.3, below, shows the rear panel of the RPG5-2602-2C series switch that is equipped with one 8-pin
redundant power inputs (48-55VDC) and one 2-pin terminal block for relay output.
Figure 2.3: The Rear Panel of RPG5-2602-2C Series
PoE Status LED indicator (Port 1-24)
LEDs for Power1, Power2, Fault,
Master, Ring
Reset Button
RS-232 Serial Console
USB 2.0 for Configuration Backup/Restore
10/100/1000Tx RJ45 PoE+
Copper Port (Port 1-24)
10/100/1000Mbps Copper Link/Act
LED indicator (Port 1-24)
100/1000Mbps SFP Link/Act
LED indicator (Port 25-26)
(Combo Port 25-26)
10/100/1000Tx RJ45 Copper
Port & 100/1000 SFP Port
1Gbps Copper Link/Act LED indicator
10/100Mbps Copper Link/Act
LED indicator
Power Input 2
Connector
Power Input 1
Connector
24VDC@1A Relay Output
Grounding Screw

5
LED Indicators
There are LED light indicators located on the front panel of the industrial switch that display the power status
and network status. Each LED indicator has a different color and has its own specific meaning, see below in
Table 2.1.
LED
Color
Description
P1
Green
On
Power input 1 is active
Off
Power input 1 is inactive
P2
Green
On
Power input 2 is active
Off
Power input 2 is inactive
FAULT
Green
On
No event happened
Red
On
1. System booting
2. Configured event happens
Flashing
Firmware upgrading
MASTER
Green
On
ERPS Owner Mode (Ring Master) is ready
Off
ERPS Owner Mode is not active
RING
Green
On
ERPS Ring Network is active and works well
Flashing
ERPS Ring works abnormally or misconfigure
Off
ERPS Ring Network is not active
GE
(LAN Port 1-24)
Green
On
Connected to network, 10/100/1000Mbps
Flashing
Networking is active
Off
Not connected to network
PoE
(LAN Port 1-24)
Green
On
Supplying power to the powered-device
Off
Not connected to a Powered Device
Combo Port
1G
(LAN Port 25-26)
On
Connected to network, 1000Mbps
Flashing
Networking is active
Off
Not connected to network
Combo Port
10/100
(LAN Port 25-26)
On
Connected to network, 10/100Mbps
Flashing
Networking is active
Off
Not connected to network
Combo Port
L/A
(SFP Port 25-26)
Green
On
Connected to network, 1000Mbps
Flashing
Networking is active
Off
Not connected to network
Amber
On
Connected to network, 100Mbps
Flashing
Networking is active
Off
Not connected to network
Table 2.1: LED Indicators

6
Ethernet Ports
RJ-45 Ports (Auto MDI/MDIX)
The RJ-45 ports are auto-sensing for 10Base-T, 100Base-TX or 1000Base-T devices
connections. Auto MDI/MDIX means that the switch can connect to another switch
or workstation without changing the straight-through or crossover cabling. See the
figures as below for straight-through and crossover cabling schematics.
10/100BASE-T(X) RJ-45 Pin Assignments (Table 2.2)
Crossover Cable
Straight Through Cable
Pin Number / Signal
Pin Number / Signal
Pin Number / Signal
Pin Number / Signal
1 / RX+
3 / TX+
1 / RX+
1 / TX+
2 / RX-
6 / TX-
2 / RX-
2 / TX-
3 / TX+
1 / RX+
3 / TX+
3 / RX+
6 / TX-
2 / RX-
6 / TX-
6 / RX-
Table 2.2
1000BASE-T RJ-45 Pin Assignments (Table 2.3)
Crossover Cable
Straight Through Cable
Pin Number / Signal
Pin Number / Signal
Pin Number / Signal
Pin Number / Signal
1 / TP0+
3 / TP1+
1 / TP0+
1 / TP1+
2 / TP0-
6 / TP1-
2 / TP0-
2 / TP1-
3 / TP1+
1 / TP0+
3 / TP1+
3 / TP0+
4 / TP2+
7 / TP3+
4 / TP2+
4 / TP3+
5 / TP2-
8 / TP3-
5 / TP2-
5 / TP3-
6 / TP1-
2 / TP0-
6 / TP1-
6 / TP0-
7 / TP3+
4 / TP2+
7 / TP3+
7 / TP2+
8 / TP3-
5 / TP2-
8 / TP3-
8 / TP2-
Table 2.3
Note: “+” and “-” signs represent the polarity of the wires that make up each wire pair.