Leonton REG5-2602-2C Series User manual

LEONTON
REG5-2602-2C Series
(REG5-2602-2C / REG5-2602-2C-T)
User Manual

© Copyright 2018 LEONTON Technologies, Co. Ltd.
All Rights Reserved
This document contains information, which is protected by copyright. Reproduction, adaptation or
translation without prior permission is prohibited, except as allowed under the copyright laws.
Disclaimer
LEONTON Technologies, Co. Ltd. provides this manual without warranty of any kind, expressed or
implied, including but not limited to the implied warranties of merchantability and fitness for a
particular purpose. LEONTON Technologies, Co. Ltd. may make improvements and/or changes to
the product and/or specifications of the product described in this manual, without prior notice.
LEONTON Technologies, Co. Ltd. will not be liable for any technical inaccuracies or typographical
errors found in this guide. Changes are periodically made to the information contained herein and
will be incorporated into later versions of the manual. The information contained is subject to
change without prior notice.

FCC Notice
This equipment has been tested and found to comply with the limits for a Class-A digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy. It may cause harmful interference to radio communications if the
equipment is not installed and used in accordance with the instructions. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications not expressly approved by the grantee of this device could
void the user's authority to operate the equipment.
CE Mark Warning
This is a Class-A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
This document is the current official release manual. Please check our website (www.leonton.com)
for any updated manual or contact us by e-mail ([email protected]).

Contents
Overview ................................................................................................................................................1
Software Features..........................................................................................................................1
Hardware Features.........................................................................................................................1
Package Contents...........................................................................................................................2
Safety Precaution ...........................................................................................................................2
Hardware Description ............................................................................................................................4
Physical Dimensions.......................................................................................................................4
Front Panel.....................................................................................................................................5
Rear Panel ......................................................................................................................................5
LED Indicators.................................................................................................................................5
Ethernet Ports................................................................................................................................7
Cabling............................................................................................................................................8
Wiring the Power Input................................................................................................................10
Wiring the Fault Alarm Contact ...................................................................................................11
Grounding Note ...........................................................................................................................11
Mounting Installation...........................................................................................................................12
Rack Mounting.............................................................................................................................12
Hardware Installation...........................................................................................................................13
Installation Steps..........................................................................................................................13
Maintenance and Service.....................................................................................................................14
Trouble Shooting..................................................................................................................................15

1
Overview
This series is rated IP40 and installation by Rack-Mount. Each unit of this industrial gigabit
managed Ethernet switch series has 24*10/100/1000Tx and 2 Gigabit combo ports
(2*10/100/1000Tx RJ45 or 2*100/1000 SFP slots), suitable for applications that require high
bandwidth and long distance communication.
In order to prevent unregulated voltage, this series provides high EFT and ESD protection. This
also allows it to function in harsh environments, as well as support power redundancy with a dual
power input design with reverse polarity protection. The built-in relay warning function alerts
users about occurring power failures.
With one model having an operating temperature of -10 to 65°C, and another with a wide
operating temperature of -40 to 75°C, this series is designed to meet any needs for industrial
automation, outdoor application and harsh environments.
Software Features
Software Features
Layer 3 Switching
Static Routes
Management
CLI, Http, Https, SNMP, SSH, Telnet
Security
Access Management, ACL, ARP Inspection, DHCP Snooping, IP Source
Guard, Multiuser Account, Port Security Limit Control, RADIUS,
TACACS+, 802.1Q VLAN, IP Subnet-based VLAN, MAC-based VLAN,
Private VLAN, Protocol-based VLAN, GVRP
Green Ethernet
IEEE 802.3az EEE (Energy Efficient Ethernet)
Network Reliability
STP, RSTP, MSTP, ERPS (G.8032)
Multicast
IGMP snooping, MLD snooping, MVR
Traffic Control
LACP, QoS (CoS/ToS)
Monitor
LLDP, LLDP-MED, Port Mirroring, RMON, MIB, sFlow, Syslog Server
DHCP
DHCP Server/Client/Relay/Snooping
Other
ICMP Ping, ICMPv6 Ping, Loop Protection, Storm Protection, NTP Client
PoE Management
(For PoE Models)
PoE Alive Check, PoE Power Budget Managed, PoE Scheduled
Hardware Features
Interface & Performance
•All Copper ports support auto MDI/MDI-X function
•Embedded 24*10/100/1000Tx and 2*gigabit combo ports (2*10/100/1000Tx copper ports

2
or 2*100/1000 SFP Slots)
•Store-and-forward switching architecture
•8K MAC Address Table
•Supports 9.6Kbytes Jumbo Frame
•4Mbits memory buffer
Power Input
●One power 90VAC~264VAC) with AC socket
●Relay Contact: 24 VDC, 1A resistive
Certification
•CE/FCC
Operating Temperature
•Standard operating temperature model: -10°C ~ 65°C
•Extended operating temperature model (–T): -40°C ~ 75°C
Case/Installation
•IP-40 protection
•Installation in a Pollution Degree 2 industrial environment
•Rack-mount design
Package Contents
•1 - REG5-2602-2C(-T)
•2 - Rack-mounting brackets and screws
•1 - RJ45 to DB9 Serial Console cable
•1 - QIG
Safety Precaution
Warning Labels
The caution label means that you should check the certain information on user manual when
working with the device. (Shown in Figure 1.1)
Figure 1.1: Caution Label
This warning label is on the device, and means that the surface of the device is hot. (Shown
in Figure 1.2)

3
Figure 1.2: Hot Surface Warning Label

4
Hardware Description
Physical Dimensions
Figure 2.1, below, shows the physical dimensions of REG5-2602-2C series.
(W x D x H) is 440mm x 200mm x 44mm
Figure 2.1: REG5-2602-2C Series Physical Dimensions

5
Front Panel
The front panel of the REG5-2602-2C series industrial Gigabit managed Ethernet switch is
shown below in Figure 2.2.
Figure 2.2: The Front Panel of REG5-2602-2C Series
Rear Panel
Figure 2.3, below, shows the rear panel of the REG5-2602-2C series switch that is equipped with
one AC power inputs socket (90-264VAC) and one 2-pin terminal block for relay output.
Figure 2.3: The Back Panel of REG2-2602-2C Series
LED Indicators
There are LED light indicators located on the front panel of the industrial Ethernet switch that
display the power status and network status. Each LED indicator has a different color and has
its own specific meaning, see below in Table 2.4.

6
LED
Color
Description
PWR
Green
On
Power input is active
Off
Power input is inactive
FAULT
Green
On
No event happened
Red
Off
1. Power input 1 or 2 is inactive
2. Port link-down/Broken
MASTER
Green
On
ERPS Owner Mode (Ring Master) is ready
Off
ERPS Owner Mode is not active
RING
Green
On
ERPS Ring Network is active and works well
Flashing
ERPS Ring works abnormally or misconfigure
Off
ERPS Ring Network is not active
1G
(LAN Port 1-24)
Green
On
Connected to network, 1000Mbps
Flashing
Networking is active
Off
Not connected to network
10/100
(LAN Port 1-24)
Green
On
Connected to network, 10/100Mbps
Flashing
Networking is active
Off
Not connected to network
1G
(LAN Port 25-26
w/ Combo)
On
Connected to network, 1000Mbps
Flashing
Networking is active
Off
Not connected to network
10/100
(LAN Port 25-26
w/ Combo)
On
Connected to network, 10/100Mbps
Flashing
Networking is active
Off
Not connected to network
L/A
(SFP Port 25-26
w/ Combo)
Green
On
Connected to network, 1000Mbps
Flashing
Networking is active
Off
Not connected to network
Amber
On
Connected to network, 100Mbps
Flashing
Networking is active

7
Off
Not connected to network
Table 2.4: LED Indictors for REG5-2602-2C Series
Caution: "PWR" is the abbreviation for "Power", "L" is for "Link", and "A" is for "Activity".
Ethernet Ports
RJ-45 Ports (Auto MDI/MDIX)
The RJ-45 ports are auto-sensing for 10Base-T, 100Base-TX or
1000Base-T devices connections. Auto MDI/MDIX means that the
switch can connect to another switch or workstation without
changing the straight-through or crossover cabling. See the figures
as below for straight-through and crossover cabling schematics.
10/100BASE-T(X) RJ-45 Pin Assignments (Table 2.5)
Crossover Cable
Straight Through Cable
Pin Number / Signal
Pin Number / Signal
Pin Number / Signal
Pin Number / Signal
1 / RX+
3 / TX+
1 / RX+
1 / TX+
2 / RX-
6 / TX-
2 / RX-
2 / TX-
3 / TX+
1 / RX+
3 / TX+
3 / RX+
6 / TX-
2 / RX-
6 / TX-
6 / RX-
Table 2.5

8
1000BASE-T RJ-45 Pin Assignments (Table 2.6)
Crossover Cable
Straight Through Cable
Pin Number / Signal
Pin Number / Signal
Pin Number / Signal
Pin Number / Signal
1 / TP0+
3 / TP1+
1 / TP0+
1 / TP1+
2 / TP0-
6 / TP1-
2 / TP0-
2 / TP1-
3 / TP1+
1 / TP0+
3 / TP1+
3 / TP0+
4 / TP2+
7 / TP3+
4 / TP2+
4 / TP3+
5 / TP2-
8 / TP3-
5 / TP2-
5 / TP3-
6 / TP1-
2 / TP0-
6 / TP1-
6 / TP0-
7 / TP3+
4 / TP2+
7 / TP3+
7 / TP2+
8 / TP3-
5 / TP2-
8 / TP3-
8 / TP2-
Table 2.6
Note: “+” and “-” signs represent the polarity of the wires that make up each wire pair.
Cabling
Use the four twisted-pair, category 5e, or the above cabling for RJ-45 port connections. The cable
between the switch and the link partner (switch, hub, workstation, etc.) must be less than 100
meters (328 ft.) long.
The small form-factor pluggable (SFP) is a compact optical transceiver used in optical
communications for both telecommunication and data communication applications.
Caution: Please employ optional optical transceiver (SFP/Fixed Fiber) that complies with IEC
60825-1 and classified as Class 1 laser product.
To connect the transceiver and LC cable, please follow below steps:
Step 1 Insert the SFP transceiver module into the SFP slot as shown below in Figure 2.7. Notice
that the triangle mark is at the bottom of the SFP slot. Figure 2.8 shows SFP transceiver
module was inserted.

9
Figure 2.7: Transceiver to the SFP Module
Figure 2.8: Transceiver Inserted
Step 2 Insert the fiber cable of the LC connector into the transceiver as shown below in Figure
2.9.
Figure 2.9: LC Connector to the Transceiver
To remove the LC connector from the transceiver, please follow the steps shown below:
Step 1 Press the upper side of the LC connector from the transceiver and pull it out to release
as shown below in Figure 2.3

10
Figure 2.3: Remove LC Connector
Step 2 Push down the metal clasp and pull the transceiver out by the plastic part as shown
below in Figure 2.4
Figure 2.4: Pull Out from the SFP Module
Wiring the Power Input
Caution: Please follow the below steps to insert the power wire.
Step 1 Insert the AC power cable into the universal AC socket as shown below in Figure 2.5.
Figure 2.5: AC Power Socket
Step 2 Switch the power switch for power on.

11
Wiring the Fault Alarm Contact
The fault alarm contact is in the middle of the terminal block connector as the picture shows
below in Figure 2.6. By inserting the wires, it will detect the fault status including power failure
or port link failure (managed industrial switch only) and form a normally open circuit. An
application example for the fault alarm contact is shown below in Figure 2.6.
Figure 2.6: Wiring the Fault Alarm Contact
Caution: The wire gauge for the terminal block should range between 12 ~ 24 AWG.
Grounding Note
Grounding and wire routing help limit the effects of noise due to electromagnetic interference
(EMI). Run the ground connection from the ground screw to the grounding surface prior to
connecting devices. The grounding screw symbol is shown blow in Figure 2.15.
Figure 2.15: Grounding screw
Caution: Using a shielded cable achieves better electromagnetic compatibility.

12
Mounting Installation
Rack Mounting
This switch can be mounted in a standard 19-inch rack with rack-mount kits. Please follow the step
to install rack-mounting switch.
Locate one plate to align with the holes on one side of the switch and secure it with the plate
screws and then attach the remaining plate to the other side of the switch. Please refer to the
Figure 3.1
Figure 3.1: The Rear Side of the Switch and DIN-Rail Bracket
Caution: The torque for tightening the screws on the device is 3.5 in-lbs.

13
Hardware Installation
Installation Steps
This section will explain how to install REG5-2602-2C series.
Caution: This device is intended for use indoor and at altitudes up to 2000 meters.
Caution: The device is intended to be installed in an industrial control enclosure and panel
Installation Steps
Step 1. Unpack the industrial Ethernet switch from the original packing box.
Step 2. Check if the rack-mount bracket is screwed on the industrial Ethernet switch.
•If the rack-mount bracket is not screwed on the industrial Ethernet switch, please
refer to the Rack Mounting section for rack-mount bracket installation.
Step 3. Power on the industrial Ethernet switch and then the power LED light will turn on.
•If you need help on how to wire power, please refer to the Wiring the Power Inputs
section.
•Please refer to the LED Indicators section for LED light indication.
Step 4. Prepare the twisted-pair, straight-through category 5 cable for Ethernet connection.
Step 5. Insert one side of the RJ-45 cable into switch’s Ethernet port and on the other side into
the networking device’s Ethernet port, e.g. switch PC or server. The Ethernet port’s
(RJ-45) LED on the industrial Ethernet switch will turn on when the cable is connected
to the networking device.
•Please refer to the LED Indicators section for LED light indication.
Step 6. When all connections are set and the LED lights all show normal, the installation is
complete.

14
Maintenance and Service
•If the device requires servicing of any kind, the user is required to disconnect and remove it
from its mounting. The initial installation should be done in a way that makes this as
convenient as possible.
•Voltage/Power lines should be properly insulated as well as other cables. Be careful when
handling them so as to not trip over.
•Do not under any circumstance insert foreign objects of any kind into the heat dissipation
holes located in the different faces of the device. This may not only harm the internal layout,
but might cause harm to user as well.
•Do not under any circumstance open the device for any reason. Please contact your dealer for
any repair needed or follow the instructions within the manual.
•Clean the device with dry soft cloth.

15
Trouble Shooting
•Verify you have the right power cord or adapter. Never use a power supply or adapter with a
non-compliant DC output voltage or it will burn the equipment.
•Select the proper UTP or STP cable in order to construct the network. Use an unshielded
twisted-pair (UTP) or shield twisted-pair (STP) cable for RJ-45 connections: 100Ω Category 5e
for 10M/100Mbps. Also be sure that the length of any twisted-pair connection does not
exceed 100 meters (328 feet).
•Diagnosing LED Indicators: To assist in identifying problems, the switch can be easily
monitored with the LED indicators which help to identity if any problems exist.
◆Please refer to the LED Indicators section for LED light indication.
•If the power indicator LED does not turn on when the power cord is plugged in, the user may
have a problem with the power cord. Check for loose power connections, power losses or
surges at the power outlet.
◆Please contact LEONTON for technical support service, if the problem still cannot be
resolved.
•If the industrial switch LED indicators are normal and the connected cables are correct but
the packets still cannot transmit, please check the system’s Ethernet devices’ configuration
or status.