Leotek Safeguard User manual

Page 1 of 4
© 2021 Leotek Electronics USA LLC. SAFEGUARD_Installaon Guide_11-1-2021
Step 3 - Loosen the slip-er bracket bolts and insert the mounng arm. The
maximum outside diameter for the mounng arm is 2-3/8” (60.3mm). The
minimum outside diameter for the mounng arm is 1-5/8” (41.28mm).
Mounng arm to be placed “stopped” against appropriate step required
to achieve desired degree of lt. Steps vary from from 0o to 2.5o.
This procedure is designed as an installaon aid. Skilled tradespeople that are familiar with general construcon and electrical installaon
techniques should perform the installaon. Licensed electricians should provide electrical installaon connecons. Installaons and
connecons should be done in accordance with all naonal and local codes and permits. In no way is this document intended to construe
warranty or tness of use of the products described, nor is it intended to provide safety instrucon for those installing the product.
WARNING
Before proceeding with installaon or service maintenance of this product:
• Disconnect power to reduce electrical shock risk.
• Review the enre Installaon Guide.
• Inspect this properly packaged product for any damage that may have occurred during transit.
• Verify product applicaon complies with manufacturer design recommendaons.
• Verify the availability of necessary tools and incidental material.
• Verify applicable code requirements. Field assembly and installaon are subject to acceptance by local inspecon authority.
• Appropriate safety equipment to be determined by end user, per applicable safety standards and precauons.
SafeguardTM UTL Ulity Light Installaon Guide
Step 1 - Pull forward on the retaining clip to unfasten the door latch.
Luminaire Installaon
Step 2 - Li the door and pull it open to access internal components.
Complete product documentaon
available online at:
hps://leotek.com/lighng-library/
Informaon provided subject to change without noce.
Leotek Electronics USA LLC | 1955 Lundy Avenue | San Jose, CA 95131
408.380.1788 | www.leotek.com

Page 2 of 4
© 2021 Leotek Electronics USA LLC. SAFEGUARD_Installaon Guide_11-1-2021
SafeguardTM UTL Ulity Light Installaon Guide
Step 5 - Adjust Drive Current/Light Output
An oponal CS output selector is used to adjust the illuminaon levels and circuit
loading. Please refer to SafeGuardTM specicaon sheet for specic details.
Step 6 - Connect the green conductor to the ground chassis marked “G”(shown to the right of the terminal block).
Step 7 - Connect the black conductor (Hot 1) to the input terminal marked “L”.
Step 8 - Connect the white conductor (Neutral) or second black conductor (Hot 2) to the input terminal marked “N”
according to Wiring Table.
Step 9 - Close the door.
8-step Current Selector
154_530
246_450
337_370
434_330
521_205
6, 7, 8 54_530
Unit: W_IOUT(mA)
Step 4 - Securely ghten bolts to 16±2lbs-.
(22Nm ± 3Nm) by alternang from bolt to bolt in
equal measured amounts of 25% torque. (See
image below for ghtening order) Ensure that the
slip-er bracket does not lt completely to one
side and refrain from unevenly ghtening bolts, as
it will cause cross-threading.
Step 10 - If luminaire is furnished with photocontrol receptacle,
install the photo control or shorng cap.
WARNING: Avoid ghtening bolts unevenly,
as it may cause cross-threading.
,

Page 3 of 4
© 2021 Leotek Electronics USA LLC. SAFEGUARD_Installaon Guide_11-1-2021
Oponal Color Temperature Filter (CTF) and Glare Shields.
SafeguardTM UTL Ulity Light Installaon Guide
Model No Hardware Type
1
H36211000001 E-Type Buckle,ID3
2
H32026000001 Flat Washer,M4,10*4.5*1.5mm
SAFEGUARDTM DROP-DOWN REFRACTOR
LEOTEK ELECTRONICS USA, LLC
1955 LUNDY AVENUE
SAN JOSE, CA 95131
PHONE: [phone]
FAX: [phone]
5 ±0.55 13 ±0.5
10 ±0.3
3
2
1
3
H11029310001 Screw,Cheese,Sloed,M4*10mm
Quanity
2
2
2
DR Drop-down Refractor Lens
4
1
401.5
222.2
Color Temperature Filter
Part# CTFUTL16
House Side Shield
Part# HSSUTL16
Front Side Shield
Part# FSSUTL16
NEMA
Dropdown Lens
(Provided by others)
Drop-down
Refractor Lens
Part# DR
Color Temperature Filter
Part# CTFUTL16
Converts 4000K to 2700KConverts 3000K to 2200K

Page 4 of 4
© 2021 Leotek Electronics USA LLC. SAFEGUARD_Installaon Guide_11-1-2021
Model No Model Name
1WBDB WALL BRACKET - DARK BRONZE
2WBBK WALL BRACKET - BLACK
3WBWH WALL BRACKET - WHITE
4WBGY WALL BRACKET - GRAY
WALL HORIZONTAL ARM BRACKET
LEOTEK ELECTRONICS USA,LLC
1955 LUNDY AVENUE
SAN JOSE, CA 95131
PHONE: [phone]
FAX: [phone]
NOTE: Installaon hardware provided by installer.
WALL BRACKET
Model No Model Name
PTBPole Top Bracket
PTB Pole Top Bracket
LEOTEK ELECTRONICS USA, LLC
1955 LUNDY AVENUE
SAN JOSE, CA 95131
PHONE: [phone]
FAX: [phone]
ANSI C136.21 Compliant
12”
NOTES:
1. Slip fits 2⅜” tenon
2. Mounng Hardware provided with bracket: 3⁄8”-16 X 3⁄4” H.H.C.S. (2 SETS OF 2 @ 90o)
3. Specify color when ordering (GY: Gray, DB: Dark Bronze, BK: Black).
POLE TOP BRACKET
Model No Model Name
PTB2 Pole Top Bracket - Twin Arm
PTB Pole Top Bracket - Twin Arm
LEOTEK ELECTRONICS USA, LLC
1955 LUNDY AVENUE
SAN JOSE, CA 95131
PHONE: [phone]
FAX: [phone]
ANSI C136.21 Compliant
15”
POLE TOP BRACKET - TWIN ARM
NOTES:
1. Slip fits 2⅜” tenon
2. Mounng Hardware provided with bracket: 3⁄8”-16 X 3⁄4” H.H.C.S. (2 SETS OF 2 @ 90o)
3. Specify color when ordering (GY: Gray, DB: Dark Bronze, BK: Black).
Model No Model Name
RPBRound Pole Bracket
RPB Round Pole Bracket
LEOTEK ELECTRONICS USA,LLC
1955 LUNDY AVENUE
SAN JOSE,CA 95131
PHONE: [phone]
FAX: [phone]
ROUND POLE BRACKET
NOTES:
1. ANSI C136.13 Compliant
2. Compable with pole diameters from 3”to 6”
3. Installaon hardware provided by installer.
4. Specify color when ordering (GY: Gray, DB: Dark Bronze, BK: Black).
Mounng Accessories
PTB - Pole Top Tenon Horizontal Arm Bracket PTB2 - Pole Top Tenon Horizontal Arm Bracket (2@180o)
RPB - Round Pole Horizontal Arm Bracket
WB - Wall Horizontal Arm Bracket
Mounng Hardware provided with bracket
3⁄8”-16 X 3⁄4” H.H.C.S. (2 SETS OF 2 @ 90o)
Installaon hardware provided by installer
Mounng Hardware provided with bracket
3⁄8”-16 X 3⁄4” H.H.C.S. (2 SETS OF 2 @ 90o)
Installaon hardware provided by installer
Slip ts 2⅜” tenon
RPB Bracket ts pole with
3” to 6” outside diameter
6” Long Mounng Arm
6” Long Mounng Arm
Slip ts 2⅜” tenon
SafeguardTM UTL Ulity Light Installaon Guide
Specicaon drawings for mounng accessories are available at
hps://leotek.com/lighng-library/
PA-24 - 24” Pipe Arm Accessory
PA-18 - 18” Pipe Arm Accessory
[609.6 mm]
24”
[249 mm]
9.8”
[457.2 mm]
18”
[249 mm]
9.8”