Leotek Arieta AR13 User manual

Page 1 of 5
Arieta LED Area Light - AR13/AR18 Series
Installaon Guide
This procedure is designed as an installaon aid. Skilled tradespeople that are familiar with general
construcon and electrical installaon techniques should perform the installaon. Licensed electricians should
provide electrical installaon connecons. Installaons and connecons should be done in accordance with all
naonal and local codes and permits. In no way is this document intended to construe warranty or tness of
use of the products described, nor is it intended to provide safety instrucon for those installing the product.
WARNING
Before proceeding with installaon or service maintenance of this product:
• Disconnect power to reduce electrical shock risk.
• Review the enre Installaon Guide.
• Inspect this properly packaged product for any damage that may have occurred during transit.
• Verify product applicaon complies with manufacturer design recommendaons.
• Verify the availability of necessary tools and incidental material.
• Verify applicable code requirements. Field assembly and installaon are subject to acceptance by local inspecon authority.
• Appropriate safety equipment to be determined by end user, per applicable safety standards and precauons.
© 2019 Leotek Electronics USA LLC
AR13-18_Installaon_Guide_N-Series_02-13-19

Page 2 of 5
Step 3 - Hang the
luminaire on top bolt.
Step 4 - Align boom holes
in the luminaire and back
plate with closest hole
in the pole, install lower
bolt, and ghten upper nut/
washer and lower bolt.
Step 5 - Connect grounding
wire to grounding screw.
BB
E
F
E
F
Arieta LED Area Light - AR13/AR18 Series
Installaon Guide
Step 6 - Adjust Drive Current
Drive current should comply with designed illuminaon levels and circuit
loading. Consult with design engineer before changing. If a new drive current
is required, open the connector and change the connecon according to the
current selector diagram installed in the xture. Note: If the FDC opon or CR
opon was ordered, the drive current cannot be changed.
D
Step 1 - Install the
back plate
inside the pole with
top bolt.
Install nut/washer
near end of bolt.
A
Standard Luminaire Installaon
A
Step 2 - Open the power door.
B
B
C
© 2019 Leotek Electronics USA LLC
AR13-18_Installaon_Guide_N-Series_02-13-19
• Arieta’s universal mount is ideal for retrot applicaons
• For new installaons, see page 5 for drilling dimensions
• See page 4 for Wall Mount installaon
C
D

Page 3 of 5
Step 9: Close the
power door. C
C
Step 10: If luminaire is furnished
with photocontrol receptacle, install
the photocontrol or shorng cap.
F
F
Step 7 - Connect the black conductor (Hot) to the input terminal marked “L1”.
Step 8 - Connect the white conductor (Neutral) or second black conductor (Hot 2) to the input terminal
marked “N” according to Wiring Table.
Electrical Wiring Connecon
Wiring Table
MV*
(120/220/277V)
HV*
(347/480V)
L1 Hot 1 Hot 1
NNeutral
Hot 2 (208V/240V) Hot 2
L2 Don’t Connect Don’t Connect
* All Power Supplies are Auto-Sensing
Arieta LED Area Light - AR13/AR18 Series
Installaon Guide
© 2019 Leotek Electronics USA LLC
AR13-18_Installaon_Guide_N-Series_02-13-19

Page 4 of 5
Step 1 - The wall mount uses fasteners and back plate provided
with AR13/18. Insert the back plate inside the wall mount
with sloed hole facing up. Insert bolt provided through the sloed
hole and into threaded hole at the top center of the wall mount.
Tighten bolt so back plate is secure against the back side of the wall
mount with top of sloed hole resng on top of the bolt.
Arieta LED Area Light - AR13/AR18 Series
Wall Mount Opon (WM) Installaon Guide
A
B
C
D
Step 3 - Open the Arieta power door and insert the
bolt protruding from the wall mount through the center
top sloed hole in the mounng base of the Arieta
luminaire. Rest the xture on the bolt and secure it with
washer and nut provided.
Step 4 - Insert and ghten the second bolt provided into
the corresponding threaded hole in the back plate.
C
B
Step 2 - Drill four mounng holes in wall corresponding with
template shown. Secure the wall mount to the wall with 1/4”
anchor bolts (provided by others). Use bolts and anchors that
are appropriate for mounng surface. Use at head bolts if
ush look is desired. Wiring may be run directly through the
large center hole or through knockouts for 1/2” conduit on top,
boom and sides of wall mount to accommodate surface wiring.
BA
D
A
Step 1
Step 2
Steps 3 & 4
Knockouts for 1/2” conduit
D
2.75”
9”
© 2019 Leotek Electronics USA LLC
AR13-18_Installaon_Guide_N-Series_02-13-19

Page 5 of 5
Informaon provided subject to change without noce.
Leotek Electronics USA LLC | 1955 Lundy Avenue | San Jose, CA 95131
408.380.1788 | www.leotek.com
Model No Model Name
BP ARIETA BACK PLATE
ARIETA™ BACK PLATE DIMENSIONS
LEOTEK ELECTRONICS USA, LLC
1955 LUNDY AVENUE
SAN JOSE, CA 95131
PHONE: (408) 380-1788
FAX: (408) 518-8128
Mounting Pole Drilling Dimensions
Arieta Housing Rear Mount
3.78”
0.39”
0.94”
1.38”
3/4”
5-5/8”
3/4”
0.394”
2.0”
1.181”
0.874”
1.496”
0.539”
0.539”
0.539”
Back Plate
2-5/8”
7/16”
7/16”
0.75”
Top of Pole
Top of Fixture
© 2019 Leotek Electronics USA LLC
AR13-18_Installaon_Guide_N-Series_02-13-19
This manual suits for next models
1
Table of contents