Let's Go Aero B02141 User manual

Page 1 of 3
V-Lectric Fat eBike Adapter Kit
Fat wheel cradles and straps for one (1) fat bike
Part No. B02141
Revision Date: 04/08/21VLB01892-040821Rev
ASSEMBLY, INSTALLATION, AND OPERATION INSTRUCTIONS
For More Information & Accessories, Visit our Website - www.LetsGoAero.com
For Technical Support & Product Questions Contact Us at 877-464-2376 or 719- 630-3800
Email: [email protected]
Adapter kit accessory for V-Lectric Models B01892 and B01175.
Maximum per bicycle load limit is 75 lbs.
NOTICE: All Manual information is subject to change without notice. Revised editions
will be available for free download at LetsGoAero.com. Manual information is considered
factual until made obsolete by a revised version.
Follow this QR-Code or visit
LetsGoAero.com/manuals to check for an updated version:
Copyright© 2021, Lets Go Aero, Inc., All rights reserved. PATENTS PROTECTED
PRODUCT MANUAL
A
B
C
D
4
2
2
4
CRADLE HOUSING
FAT UPPER WHEEL CRADLE
FAT LOWER WHEEL CRADLE
EXTRA-LONG RUBBER STRAPS
QTY. DESCRIPTION
PARTS

Page 2 of 3
Pull out the Knob located on the Cradle Housing [A]
installed above the foam bumpers on each Wing, insert
an Upper Wheel Cradle [B] with Rubber Strap [D] and
then release the Knob as shown. [Fg. 4 & 5]
Perform a small
pull on the Upper
Wheel Cradle
[B] to ensure
the knob is fully
seated and the
Cradle has been
secured.
Turn the handles on each Cradle Housing [A] to loosen their grip.
Slide one Cradle Housing [A] on the Wing above the foam bumpers and one
Cradle Housing below the foam bumpers.
NOTE: The Knobs located on each Cradle Housing [A] MUST rest along the
same sides as the connection hole located at the bottom of the Wing. [Fg. 1]
Re-tighten each Cradle Housing [A] handle to secure in place on the Wing. [Fg.
2]
Repeat this step for the second Wing.
A
A
A
A
AA
STEP 1:
HANDLE
WING
KNOB
FOAM
BUMPERS
CONNECTION
HOLE
[Fg. 1]
[Fg. 2]
C
B
STEP 2:
Slide the round end of one (1) Rubber Strap [D] onto
each Upper Wheel Cradle [B] and Lower Wheel
Cradle [C]. [Fg. 3]
NOTE: Be sure to slide the Rubber Straps [D] all the
way onto the cradles so that it tightly rests over the
plastic coating of the Wheel Cradle [B & C]; this is a
tight t.
[Fg. 3]
D D
B
B
D
STEP 3:
[Fg. 4]
[Fg. 5]

Page 3 of 3
A
To register your product, visit the LetsGoAero.com/registration
Technical Support
For assistance with this product, please contact us:
Let’s Go Aero, Inc.
5353 N. Union Blvd. Suite 103
Colorado Springs, CO 80918 USA
Phone: [phone] or 719-630-3800
Email: [email protected]
To learn more about our products and stay informed about useful options for transporting all kinds of
gear with your carrier, be sure to visit our website: www.LetsGoAero.com
Copyright© 2021, Lets Go Aero, Inc., All rights reserved.
Always check and conrm “knobs” on each cradle housing are fully seated on the wheel cradle and secured before
each transit. Failure to follow proper installation and equipment checks before transit may result in damage to
carrier, damage to property, bodily injury or death.
WARNING:
STEP 4:
In the same manor as before, pull out the Knob located on
the Cradle Housing [A] installed below the foam bumpers
on each Wing, insert a Lower Wheel Cradle [C] with Rubber
Strap [D] and then release the Knob as shown. [Fg. 6]
Perform a small pull on the Lower Wheel Cradle [C] to ensure
the knob is fully seated and the Cradle has been secured.
[Fg. 6]
C
D