LevelOne FSW-1621 User manual

LevelOne
FSW-1621
FSW-2421
16/24-port 10/100BASE-TX
Fast Ethernet Switch
User Manual
Rev.2.00-0705

1. Introduction
Congratulations on your purchase of FSW-1621/2421.
The FSW-1621/2421, 16/24-port 10/100Base-TX Switch, is a multi-port
Switch that can be used to build high-performance switched workgroup
networks. This switch is a store-and-forward device that offers low latency
for high-speed networking. The Switch is targeted at workgroup,
department or backbone computing environment at SME (small, medium
enterprise) business.
The 16/24-port 10/100Base-TX Switch features a “store-and-forward
“switching scheme. This allows the switch to auto-learn and store source
address on 8K/4K-entry MAC address table.
Features
Conforms to IEEE 802.3, 802.3u and 802.3x
16/24 10/100 Base-TX RJ-45 Ethernet ports
Auto-MDIX on all ports
IEEE 802.3x flow control support
¾Flow control on full-duplex
¾Back pressure on half-duplex
N-Way Auto-Negotiation supported
Store-and-Forward switching architecture and no-blocking full wire
speed
Back plane Bandwidth 4.8 Gbps for FSW-2421
Back plane Bandwidth 3.2 Gbps for FSW-1621
8K/4K MAC address table for FSW-1621/2421
10” size

2
Package Contents
Unpack the contents of the 16/24-port 10/100Base-TX Switch and verify
them against the checklist below.
FSW-1621/2421 X 1
User Manual
19” Rack Mount kit
Power Cord
Four Rubber Feet
16/24-port 10/100Base-TX Switch User Guide 19” Rack-Mount Kits
Power Cord Rubber Feet
Figure 1-2. Package Contents
Compare the contents of your FSW-1621/2421 10/100Base-TX Switch
package with the standard checklist above. If any item is missing or
damaged, please contact your local dealer for service.

2. Hardware Description
This Section mainly describes the hardware of the 16/24-port
10/100Base-TX Switch, and gives a physical and functional overview of
this Switch.
The physical dimensions of the FSW-1621/2421 is:
250mmx 133 mm x 37mm (L x W x H)
Front Panel
FSW-1621/2421 consists of 16/24 x 10/100Base-TX RJ-45 ports. The
LED Indicators are also located on the front panel of the Switch.
Figure 2-1. The Front view of FSW-1621/2421
RJ-45 ports (Auto MDI/MDIX): 16/24x 10/100Mbps auto-sensing port for
10Base-T or 100Base-TX devices connection.
[In general, MDI means connecting to another Hub or Switch while MDIX
means connecting to a workstation or PC. Therefore, Auto MDI/MDIX
means that you can connect to another Switch or workstation without
changing non-crossover or crossover cabling.]

4
LED Indicators
The LED Indicators gives real-time information of systematic operation
status. The following table provides descriptions of LEDs status and their
meaning.
Figure 2-2. LED Indicators
LED Status Description
Green Power On
Power Off Power is not connected
Green The port is connecting with the device
Blinks The port is receiving or transmitting data
LK/ACT
Off No device attached
Table 2-1. The Descriptions of LED Indicators
Rear Panel
The 3-pronged power plug is located at the rear panel of the 16/24-port
10/100Base-TX Switch as show in the Figure 2-3. The Switch will work
with AC in the range 100-240V AC, 50-60Hz.
Figure 2-3. The Rear Panel of FSW-1621/2421

Desktop Installation
Attaching Rubber Feet
A. Make sure mounting surface on the bottom of the Switch is grease and
dust free.
B. Remove adhesive backing from your Rubber Feet.
C. Apply the Rubber Feet to each corner on the bottom of the Switch.
These footpads can prevent the Switch from shock/vibration.
Rack-mounted Installation
FSW-1621/2421 10/100Base-TX Switch comes with a long rack-mounted
kit and can be mounted in an EIA standard size, 19-inch Rack. The Switch
can be placed in a wiring closet with other equipment.
Perform the following steps to rack mount the switch:
A. Position one bracket to align with the holes on one side of the switch
and secure it with the smaller bracket screws. Then attach the
remaining bracket to the other side of the Switch.
B. After attached both mounting brackets, position FSW-1621/2421 in the
rack by lining up the holes in the brackets with the appropriate holes on
the rack. Secure the Switch to the rack with a screwdriver and the
rack-mounting screws.
Power On
Connect the power cord to the power socket on the rear panel of the
Switch. The other side of power cord connects to the power outlet. The
external power supply in the Switch works with AC in the voltage range
100-240VAC, frequency 50~60Hz.Check the power indicator on the front
panel to see if power is properly supplied.

6
3.Network Application
This section provides you a few samples of network topology in which the
Switch is used. In general, FSW-1621/2421 is designed as a segment
switch. That is, with its large address table and high performance, it is
ideal for interconnecting networking segments.
You can use the FSW-1621/2421 to connect PCs, workstations, and
servers to each other by connecting these devices directly to the Switch.
The switch automatically learns nodes address, which are subsequently
used to filter and forward all traffic based on the destination address. By
using Uplink port, the Switch can connect with another switch or hub to
interconnect each of your small-switched workgroups to form a larger
switched network.
Small Workgroup
The 16/24-port 10/100Base-TX Switch can be used as a standalone
switch to which personal computers, server, printer server, are directly
connect to form small workgroup.
Figure 3-1. Small Workgroup Application

Segment Bridge
For enterprise networks where large data broadcasts are constantly
processed, this switch is an ideal solution for department users to connect
to the corporate backbone.
In the illustration below, two Ethernet switches with PCs, print server, and
local server attached, are both connect to the FSW-1621/2421. All those
devices in this network can communicate with each other through
FSW-1621/2421 Switch. Connecting servers to the Switch allow other
users to access the server’s data.
Figure 3-2 Department Bridge Application

8
4.Technical Specification
This section provides the specifications of FSW-1621/2421,16/24-port
10/100Base-TX Switch.
Standard
IEEE 802.3 10BASE-T Ethernet,
IEEE 802.3u 100BASE-TX Fast Ethernet
IEEE802.3x Flow Control and Back-pressure
Protocol CSMA/CD
Technology Store and Forward switching architecture
Transfer Rate 14,880 pps Ethernet port
148,800 pps Fast Ethernet port
MAC address 4K/8K Mac address table for FSW-1621/2421
Memory Buffer 4Mbits/1.25Mbits of FSW-1621/2421
Network Cable
10BASE-T: 2-pair UTP/STP Cat. 3, 4, 5 cable
EIA/TIA-568 100-ohm (100m)
100BASE-TX: 2-pair UTP/STP Cat. 5 cable
EIA/TIA-568 100-ohm (100m)
LED Indicators Per port: Link/Activity
Per unit: Power
Back-plane 3.2/4.8Gbps for FSW-1621/2421
Dimensions 250mmx 133 mm x 37mm (L x W x H)
Operational Temp. O℃to 45℃(32℉to 113℉)
Operational
Humidity 10% to 90% (Non-condensing)
Power Supply 100-240 VAC, 50~60Hz
Power
Consumption
10Watts for FSW-1621(maximum)
19 Watts for FSW-2421(maximum)
EMI FCC Class A, CE
Safety CE/EN60950, UL, cUL